Haier HPH60ILX2 User manual

BUILT-IN INTEGRATED
RANGEHOOD
HPH60ILX2, HPH60ILB2
HPH90ILX2, HPH90ILB2
NZ AU

CONTENTS
Safety and warnings 3
Installation instructions 5
Operating instructions 13
Cleaning and maintenance 14
Parts and accessories 16
Service & Warranty 17

3
SAFETY AND WARNINGS
!
6.5 kg
(HPH60)
8.8 kg
(HPH90)
Weight Hazard
!
Electric Shock Hazard
Always disconnect the appliance from the mains power supply before
carrying out any maintenance or repairs. Alterations to the domestic wiring
system must only be made by a qualified electrician.
Failure to follow this advice may result in electrical shock or death.
IMPORTANT SAFETY INSTRUCTIONS
WARNING!
When using this appliance always exercise basic safety precautions including
Read the entire set of instructions before installing or using this appliance.
Please make this information available to the person installing the appliance –
Always switch the power off prior to installation, servicing or cleaning of
This appliance must be installed and connected to the mains power supply only
by a suitably qualified person according to these installation instructions and in
compliance with any applicable local building and electricity regulations. Failure
To comply with electrical safety regulations, the rangehood must be plugged into
a socket near the appliance. The socket must be accessible, or have an accessible
isolating switch, to enable the end user to isolate the rangehood from the power for
the purpose of internal cleaning or maintenance.
A power outlet should be within 750 mm of the motor assembly and can either be
If the supply cord of this equipment is damaged, it must only be replaced by the
manufacturer, its service agent or similarly qualified person in order to avoid a hazard.
Ducting accessories are not supplied. All ducting must comply with local requirements
and building codes.
Attention should be given to ensure that any applicable regulations concerning the
discharge of exhaust air are fulfilled.
The appliance is heavy. Please ensure adequate care is taken when
installing the appliance to prevent personal injury. The appliance must
be installed onto a solid wall, stud, beam or truss. Weight of the product
is 6.5 kg (HPH60ILX2, HPH60ILB2) / 8.8 kg (HPH90ILX2, HPH90ILB2).
●
●
●
●
●
●
●
●
●

4
Before connecting any pipes, consult municipal ordinances to ensure that any
applicable regulations concerning the discharge of exhaust air are adhered to and
request permission from the person in charge of the building.
Exhaust air must not be discharged into an existing flue that is used for exhausting
fumes from appliances burning gas or other fuels.
There shall be adequate ventilation of the room when the rangehood is used at the
same time as appliances burning gas or other fuels.
Range hoods and other cooking fume extractors may adversely affect the safe
operation of appliances burning gas or other fuels (including those in other rooms)
due to back flow of combustion gases. These gases can potentially result in carbon
monoxide poisoning. After installation of a range hood or other cooking fume
extractor, the operation of flued gas appliances should be tested by a competent
person to ensure that back flow of combustion gases does not occur.
Stainless steel is very easily damaged during installation if abraded or knocked by
tools. It is recommended to protect the top of the rangehood with cardboard or
polystyrene during the installation to minimise the risk of damage occurring.
To reduce the risk of damage occurring to the cooktop, it is recommended that
the surface of the cooktop is protected with cardboard or a similar object during
installation of the rangehood.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning the use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure they do not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
You must read the details concerning the method and frequency of cleaning.
There is a fire risk if cleaning is not carried out in accordance with the instructions.
Never leave frying food unattended since grease can overheat and catch fire.
The risk of fire is even greater in the case of used oil.
Do not flambé under the rangehood.
Never use the rangehood without the filters in place.
During an electrostatic discharge (ESD) it is possible that the device will stop
working. By switching the device off and on the device will again work as intended.
CAUTION: accessible parts may become hot when used with cooking appliances.
Remove all packaging, including protective wrappings, before use.
SAFETY AND WARNINGS
The minimum distance between the supporting surface for cooking vessels on the
cooktop and the lowest part of the rangehood shall be 600 mm. If the instructions for
installation of the cooktop require a greater minimum distance, this should be
followed.
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●

5
INSTALLATION INSTRUCTIONS
Parts Supplied
(2)
User guide
(1)
Rangehood
(1)
150 mm ducting adapter
with non return flap
(1)
BUI LT- IN INT EGRATED
RAN GEHOO D
NZ AU
HPH60ILX2, HPH60ILB2
HPH90ILX2, HPH90ILB2
Other Parts Required
Ducting – 150mm diameter,
rigid or semi-rigid (not supplied)

INSTALLATION INSTRUCTIONS
6
Product and cabinetry cutout dimensions

INSTALLATION INSTRUCTIONS
7
HPH60ILX2,
HPH60ILB2
HPH90ILX2,
HPH90ILB2
PRODUCT DIMENSIONS mm mm
AOverall height of product
(with ducting adapter)
285
(338)
315
(372)
BOverall width of product 492 792
COverall depth of product 277 277
DThickness of flange 2.5 2.5
EWidth of chassis 450 750
FDepth of chassis 255 255
GHeight of side of chassis n/a 115
HWidth of top surface of chassis 251 410
ILength of angled surface of chassis 300 261
JDistance from centre of ducting outlet 161 84
KDistance from centre of ducting outlet 225 375
LDiameter of ducting outlet 150 150
Length of power cord 1200 1200
CABINETRY CUTOUT DIMENSIONS
Overall width of cutout 460 760
Overall depth of cutout 260 260
OBase of brackets/clips to bottom of chassis
IMPORTANT!
Please read the entire instructions before installing the rangehood.
min. 15 - max. 35 min. 15 - max. 35
Note: If installing in cabinetry with base thickness >35mm remove material around the
mounting surface so that the thickness is <35mm and the brackets/clips can engage
with the surface (see below)
15mm ~ 35mm

INSTALLATION INSTRUCTIONS
8
Height of rangehood
P
MINIMUM CLEARANCES mm
PHeight top of cooktop to base of product min. 600 – max.
recommended 750
This rangehood must be installed no lower than the minimum height indicated in the table
above. Minimum installation height may be greater if required by the cooktop manufacturer
or safety and warnings section on this user guide. Installation at the minimum height will
improve efficiency of capturing cooking odours, grease and smoke. Installation at the
maximum height improves ergonomics by offering increased head room.

INSTALLATION INSTRUCTIONS
9
Induction cooking considerations
Induction cooktops use energy efficient technology that only heats the contents of a
cooking pot.
Unlike gas or traditional electric cooktops, the surrounding air does not get heated
when using an induction cooktop. As a result, rangehood filters, splashbacks and
surrounding cabinetry do not get warmed up, increasing the likelihood of condensation
on these cooler surfaces.
Other factors like ambient temperature, humidity, natural ventilation of the room, size of
the cookware and how the induction cooktop is being used also influence condensation.
For example, aggressive boiling on high cooktop heat settings like PowerBoost increases
the rate at which water is evaporated, increasing the likelihood of condensation.
It is important to understand that neither the rangehood nor the induction cooktop are
faulty as a result of this phenomenon.
Condensation can be minimised by:
Installing the rangehood at the maximum height above the cooktop as specified in
this user guide.
Using the rangehood on a lower speed setting when boiling.
Using the induction cooktop on a lower heat setting when boiling.
Venting options
Attention should be given to ensure that any applicable regulations concerning the
discharge of exhaust air are fulfilled.
The rangehood can be installed to operate with the exhaust air ducted externally from
the kitchen, or installed to operate with the exhaust air recirculating within the kitchen.
Ducted
For ducted installation it is recommended that 150 mm
diameter, rigid or semi-rigid ducting is used. This will
require a 160 mm (min) round hole in the ceiling or wall.
Care should be taken to position the hole correctly.
Vent through
roof
Vent through
external wall
For optimal efficiency use the shortest and straightest
duct route possible and use rigid or semi-rigid ducting
for reduced noise and increased airflow. Flexible metal
ducting should only be used as a last resort (ie in difficult
installations) and if used ensure thatit is straight and
smooth and extended as much as possible.
●
●
●
●
●
●
●
●

INSTALLATION INSTRUCTIONS
10
Recirculate with
carbon filters
Recirculating
Check with local codes and regulations if recirculation is allowed in
your area.
IMPORTANT!
Venting directly into the cabinet with no ducting and louvered vent is not permitted.
To recirculate your perimeter insert range hoods:
Determine the desired location of the 150mm louvered vent on your cabinetry.
The louvered vent can be placed on the side or front of your cabinet provied there is
sufficient clearance form the surrounding cabinetry to enable ventilated air to recirculate
back into your kitchen.
Note: Placement of the louvered vent on the top of your cabinetry is not recommended.
This should be only be done if objects can be prevented from falling through the louvers
in to the blower.
Create a cutout in your cabinet to fit the 150mm louvered vent. Place the louvered vent
on the hole created and secure (A).
Connect the blower outlet to the louvered vent with a length of 150mm rigid ducting,
and secure the joints with aluminum tape. Ensure there is no slack in the ducting.
①
②
③
Recirculation venting options
WARNING!
This appliance is heavy and requires two persons for unpacking and installation.
Installation work and electrical wiring must be done by qualified person(s) in
accordance with all applicable codes and standards.
Failure to install the screws or fixing device in accordance with these instructions
may result in electrical hazards.
IMPORTANT!
Wear gloves to protect against sharp edges.
The manufacturer is not liable for any damage caused by not following these instructions.
Where ducting outside is not a practical option, this rangehood can be
installed to operate with the air recirculating. Carbon filters are
required to remove odours from the air before it is channelled back
into the room or overhead bulkhead (refer to ‘Cleaning and Mainte-
nance’ section).
Ensure that the ducting outlet is not obstructed, even a partial
obstruction will restrict the efficiency of the rangehood.
●
●
●
A
Side Top Front

INSTALLATION INSTRUCTIONS
11
1 Prepare for installation.
INSTALLATION
Before installing your rangehood:
Please read the instructions carefully.
Unpack the rangehood and check that all functions are working.
Ensure that the voltage (V) and the frequency (Hz) indicated on the serial plate
match the voltage and frequency at the installation site.
The stainless steel and glass surfaces of the rangehood are very easily damaged
during installation if grazed or knocked by tools. Please take care to protect the
surfaces during installation.
Protect the cooktop surface below with cardboard, or the like, to prevent damage
occurring whilst the rangehood is being installed above.
2 Fit the 150 mm ducting adapter with non return flap to the rangehood using the screws
supplied.
3 Provide an opening on the underside of the cupboard (see product and cabinetry cutout
dimensions).
Width
Depth
4 Remove the filter from the rangehood.
●
●
●
●
●

INSTALLATION INSTRUCTIONS
12
5 Connect duct and plug rangehood in.
6 Lift the rangehood and fit through the opening of the cupboard till the spring loaded
brackets / clips hold the product in place.
7 Secure rangehood while tightening the brackets / clips.

13
OPERATING INSTRUCTIONS
Control panel
CONTROL PANEL FEATURES
Lights Turn the lights on or off.
Fan Turn the rangehood fan off.
Turn the rangehood fan on or adjust the fan speed
levels from 1 – 3 with 1 being the lowest level and 3
being the highest.
Fan speed 1 - 3

14
CLEANING ANDMAINTENANCE
WARNING!
Unplug or disconnect the appliance from the power supply before servicing
or cleaning.
IMPORTANT!
Never use abrasive or oil based cleaners.
Wear gloves to protect against sharp edges.
Maintenance
The rangehood should be cleaned regularly using a mild, liquid detergent and a clean
soft cloth to avoid a build-up of grease occurring. Avoid the use of corrosive chemicals,
abrasive cleaning products, hard brushes and steel wool pads. Grease deposits are
corrosive which can cause damage to your rangehood.
Note: in areas of high humidity or coastal environments, cleaning should be carried out
more frequently.
Aluminium filters
Depending on use, and at least once a
month, the aluminium grease filters should
be removed and cleaned with hot soapy
water or in a dishwasher.
If washed in a dishwasher, the filters should
be placed in an upright position to prevent
food from falling on them.
After rinsing and drying, replace the filters.
Note: some discolouration of the frames may occur.
Removing the aluminium filters:
1Pull the filter catch, tilting it downwards until it disengages from the supports.
2Reverse these instructions when refitting the filters.
Carbon filters – for use in recirculation mode
Active carbon filters are disposable items designed to remove grease and odours from
cooking vapours before the air is channelled back into the kitchen. The active carbon
filters must be replaced periodically to work properly, at least once every three months,
depending on the frequency with which the rangehood is used.
●
●
●
●
●
●

15
IMPORTANT!
Carbon filters are disposable items and must be replaced at least every three months.
Saturated carbon filters can become a barrier to air movement, therefore limiting
your range hoods performance.
In the event of a fire, grease laden filters could be flammable.
Fitting the carbon filters:
1Ensure the range hood is switched off.
2Remove the aluminum grease filters from the range hood.
3
4Refit aluminium grease filters.
Light bulb replacement
CLEANING ANDMAINTENANCE
BA
Place a carbon filter on each side of the blower inlet (refer to A), turn the filter until it
clips into place (refer to B).
Note: The direction will be clockwise on one side of the blower and counterclockwise on
the other side of the blower.
To replace the lights you must contact your Haier trained and supported service
technician. Refer to the haier website or your service and warranty book for contact
details.
Note: lights are not user replaceable.
●
●
●

16
PARTS AND ACCESSORIES
ITEM REFERENCE NUMBER
Aluminium filter (HPH60ILX2, HPH60ILB2) 793597
Aluminium filter (HPH90ILX2, HPH90ILB2) 793598
Recirculation carbon filter x2 792481

17
SERVICE& WARRANTY
Manufacturer’s Warranty
Please read this warranty card carefully. Attach your purchase receipt to this warranty
card and keep in a safe place. You must produce both warranty card and proof of
purchase in the event of a warranty repair being required.
When you purchase any new Haier Product you automatically receive a two year
Manufacturer’s Warranty covering parts and labour for servicing.
The Manufacturer undertakes to:
Repair or, at its option, replace without cost to the owner either for material or labour
any part of the Product, the serial number of which appears on the Product, which is
found to be defective within TWO YEARS from the date of purchase.
This warranty DOES NOT cover:
AService calls which are not related to any defect in the Product. The cost of a
service call will be charged if the problem is not found to be a Product related
fault. For example:
1. Correct the installation of the product.
2. Provide Instruction on use of the product or change the setup of the product.
3. Replace house fuses or correct house wiring.
4. Correcting fault(s) caused by the user.
5. Noise or vibration that is considered normal.
6. Water on the floor due to incorrect loading or excessive suds.
7. Blocked pumps, removal of foreign objects/substances from the machine,
including the pump and inlet house filters.
8. Correcting damage caused by pests, eg. rats, cockroaches etc.
9. Correct corrosion or discolouration due to chemical attack.
10. Power outages or surges.
BDefects caused by factors other than:
1. Normal domestic use or
2. Use in accordance with the Product’s User Guide.
CDefects to the Product caused by accident, neglect, misuse or ‘Act of God’ .
DThe cost of repairs carried out by non-authorised repairers or the cost of correcting
such unauthorised repairs.
ENormal recommended maintenance as set out in the Product ‘s User Guide.
FRepairs when the appliance has been dismantled, repaired or serviced by other than
an AUTHORISED CUSTOMER SERVICE CENTRE or the selling dealer.

18
SERVICE& WARRANTY
GPick up and delivery.
HTransportation or travelling costs involved in the repair when the product is installed
outside the AUTHORISED CUSTOMER SERVICE CENTRE’S normal service area.
This product has been designed for use in a normal domestic environment. It is not
intended for commercial use. Doing so may affect product warranty.
Service under this warranty must be provided by an Authorised Service Repairer (refer
to the Customer Care section for contact details). Such service shall be provided during
normal business hours. This warranty certificate should be shown when making any
claim.
Note:
This Warranty is an extra benefit and does not affect your legal rights and applies only
to product purchased in New Zealand and Australia. Please keep this Warranty Card in a
safe place.
For Australian customers:
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.

19
SERVICE& WARRANTY
Customer Care
Check the things you can do yourself. Refer to your User Guide and check:
1. Your appliance is correctly installed.
2. You are familiar with its normal operation.
3. You have read the problem solving section in your User Guide.
If after checking these points you still need assistance, please refer to your nearest Haier
Authorised Repairer.
In New Zealand, if you need assistance...*
Call your retailer who is trained to provide information on your appliance, or if we can
be of any further help, please contact our Customer Care Centre:
Toll Free: 0800 242 437 Fax: [phone]
Email: [e-mail]
Postal address: P.O. Box 58732, Botany, Manukau 2163
If you need service...
We have a network of independent Fisher & Paykel Authorised Repairers whose fully
trained technicians can carry out any service necessary on your appliance. Your dealer
or our Customer Care Centre can recommend a Fisher & Paykel Authorised Repairer in
your area.
In Australia, if you need assistance...*
Call the Customer Care Centre and talk to one of our Customer Care Consultants.
Toll Free: 1300 729 948 Fax: [phone]
Email: [e-mail]
Postal Address: PO Box 798, Cleveland QLD 4163
If you need service...
We have a network of qualified Authorised Repairers whose fully trained technicians
can carry out any service necessary on your appliance. Our Customer Care Centre can
recommend an Authorised Repairer in your area.
*If you call or write, please provide: name, address, model number, serial number, date of
purchase and a description of the problem. This information is needed in order to better
respond to your request for assistance.
Product Detials
Model ______________________ Serial Number: __________________
Date of Purchase Purchaser
Dealer ______________________ Suburb______________________
Town______________________ Country______________________
Thank you for choosing Haier. We are confident that you will enjoy many years of good
service from your appliance.

NZ AU
106066B
The product specifications in this document apply to the specific
products and models described at the date of issue. Under our policy
of continuous product improvement, these specifications may change
at any time. You should therefore check with your Dealer to ensure this
document correctly describes the product currently available.
60902625.17.10.2022