Haier IT9002 User manual

Service Manual

IT9002
Cooker Hood
INSTALLATION AND USER’S MANUAL

SAFETY PRECAUTION
•Important! Always switch off the electricity supply at the mains during
installation and maintenance such as light bulb replacement.
•The cooker hood must be installed in accordance with the installation
instructions and all measurements followed.
•All installation work must be carried out by a competent person or qualified electrician.
•Please dispose of the packing material carefully. Children are vulnerable to it.
•Pay attention to the sharp edges inside the cooker hood especially during
installation and cleaning.
•When installing the cooker hood, make sure that the following recommended distances
between the top of cooker and the lowest part of the cooker hood are observed:
Gas cookers: 70 cm
Electric cookers: 70 cm
Coal or oil cookers: 80 cm
•Make sure the ducting has no bends sharper than 90 degrees as this will
reduce the efficiency of the cooker hood.
•Cooker hood is for domestic use only.
•Always put lids on pots and pans when cooking on a gas cooker.
•Do not try to use the cooker hood without the grease filters or if the filters are
excessively greasy!
•When in extraction mode, air in the room is being removed by the cooker hood.
Please make sure that proper ventilation measures are being observed. The
cooker hood removes odours from room but not steam.
•There shall be adequate ventilation of the room when the range hood is used
at the same time as appliances burning gas or other fuels.
•Do not install above a cooker with a high level grill.
•Do not leave frying pans unattended during use because overheated fats or
oils might catch fire.
•Never leave naked flames under the cooker hood.
•If the cooker hood is damaged, do not attempt to use.
•If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
•This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
2

3
SAFETY PRECAUTION
•Caution: The appliance and its accessible parts can become hot during
operation. Be careful to avoid touching the heating elements. Children younger
than 8 years old should stay away unless they are under permanent supervision.
–There shall be adequate ventilation of the room when the range hood is used at
the same time as appliances burning gas or other fuels.
–There is a fire risk if cleaning is not carried out in accordance with the instructions.
–Do not flambéunder the cooker hood.
–CAUTION: Accessible parts may become hot when used with cooking appliances.
–The air must not be discharged into a flue that is used for exhausting fumes from
appliances burning gas or other fuels.
–The minimum distance between the supporting surface for the cooking vessels
on the hob and the lowest part of the range hood.
(When the range hood is located above a gas appliance, this distance shall be at least 70cm.)
–Regulations concerning the discharge of air have to be fulfilled.
•Clean your appliance periodically by following the method given in the chapter
MAINTENANCE.
•Warning: Failure to install the screws or fixing device in accordance with these
instructions may result in electrical hazards
Regarding the instructions method of fixing for the fixed appliance and how
the appliance is to be fixed to its support, thanks to refer to the section
“INSTALLATION”.
The bulbs are not replaceable.
The plug must be remained easily accessible after installation of the appliance.
Important
This instruction manual is designed to provide you with all required instructions related to the installation, use and
maintenance of the appliance. In order to operate the unit correctly and safety, please read this instruction
manual carefully before installation and usage.
We can not be held responsible for injuries or losses caused by incorrect use or installation of this product. Please
note that we reserve the right to invalidate the guarantee supplied with this product following incorrect installation or
misuse of the appliance or use in a commercial environment.
Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualified personnel
Appliance information:
Please enter the details on the appliance rating plate below for reference, to assist we Customer Care in the
event of a fault with your appliance and to register your appliance for guarantee purposes.
Appliance Model
Serial Number

Parts identification
Parts Name
(1) Extraction hood
(2) Chimney section (including upper and lower parts)
(3) Hose connector
(4) Upper wall bracket
(5) Lower wall bracket
(6) ø4mm x 10mm Screw (6 pcs)
(7) Washer (2 pcs)
(8) Wall plug (8 pcs)
(9) ø4mm x 35mm Screw (8 pcs)
(10) Exhaust hose (ø15cm)
(11)Carbon filter (required for circulating air mode)
(12) Cable tie
Technical specifications
1
2
3
4
5
6
7
8
Model
CXW-200-IT9001
Voltage
220-240V~50Hz
Product dimension
90x49x55
WxDxH(in cms)

Wattage(Total)
202W
Motor
200W
Filter
1xAluminium Filter
Light
1x2W LED lights
Noise Level
68dB
Speed control
3 Speed control
Type of switch
Touch switch
4

Installation (for venting outside)
When the cooker hood is to be installed above an electric
hob or a gas hob, the minimum distance between the hob
and cooker hood must exceed 700mm.
If the instructions for installation for the gas hob specify a
greater distance, this has to be taken into account.
The height should be measured from the top of the burners

Installation (for venting outside)
Secure hood (tighten all screws).
Fit ducting adaptor.
Fig. 9
Fig. 10
Drill holes for mounting the body.
Fix support plate on the wall by screws with expanding
plugs.
10 mm
Fig. 7
Fig. 8
T ools r equi r ed
Mark wall as required (see Fig. 6)
8
Fig. 5
Fig. 6

IMPORTANTSAFETYWARNING:ONLYUSETHESCREWSPROVIDEDWITHTHERANGEHOOD TOMOUNT
THE DUCTING ADAPTOR. THEUSEOFLONGER SCREWS MAYCAUSEDAMAGE TO THEINTERNAL WIRING
WHICH WILL NOT BECOVEREDBYTHEWARRANTY.
Fix ducting (seal joint by 3 pieces ST3X8).
Fig. 11

If you do not have an outlet for exhausting air, the exhaust hose
(part [10]) is not required, and the installation is similar to the
one shown in the section "Installation (for venting outside)".
Air is vented back into the kitchen through the opening of the
cooker hood, this circulating air mode requires the use of the
carbon filter (part [11]) to remove odors.
Attention -Remove the plastic packaging bag from the carbon
filter before use. For venting outside, carbon filter is not required.
To ensure best performance of your cooker hood, you should replace the
carbon filter every 2~3 months, depending on the frequency of use.
Check with your locad retailer or dealer to buy new carbon
filters for replacement.
8

9
Using your Cooker hood
For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run
for approximately 15 minutes after the end of cooking.
Fig. 13
ON/OFF Key/Delay Timer:
•Press the key to turn on/o the extractor. If the extractor is turned on, the delay timer can be activated by
pressing the again. The display will show the symbol flashing for 4 seconds. By pressing the keys or ,
the delay timer can be adjusted (max. 9 minutes). In order to deactivate the timer delay, press the key again.
Clock Setting
•To set the clock on your extractor, press and hold the key for 2 seconds. The clock display will flash. Use or
keys to set the hour, press key to set after which you can adjust the minutes. Once set, press key to confirm.
Please note, the clock will return to its previous setting if no key is pressed for 5 seconds whilst setting the time.
Adjusting the Fan Speed
•Once the extractor is turned on, press the key to set the fan motor to high speed. When pressed again, it
will reduce the fan speed from high to medium, to low and finally o .
Once the extractor is turned on, press the key to set the fan motor to high speed. When pressed again, it
will reduce the fan speed from high to medium, to low and finally o .
Light Key
•Press the key to turn on/o the lights. When the lights are on, the display will show the symbol .

Care and Maintenance
IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF THE COOKER
HOOD WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY.
Cleaning
You should use a nonabrasive cleaner. Any abrasive cleaner (including Cif)
will scratch the surface and could erase the control panel markings.
You can clean your cooker hood effectively by simply using a dilute
solution of water and mild detergent and then dry it with a clean cloth.
Cleaning the grease filter
The grease filter should be kept clean to minimise the risk of fire.
At least once a month you should remove and clean the grease
filter with hot soapy water. You can also wash the grease filter in a
dishwasher, ensuring that you place it in an upright position to
prevent damage from other items in the dishwasher.
To remove the grease filter, push in the button on the handle and
then pull down on the filter at the front as shown in Fig. 14.1.
After rinsing and drying the filter, replace it as shown in Fig. 14.2.
Please note:
Cleaning the grease filter in the dishwasher may lead to discoloration.
This is normal and does not constitute a fault with the appliance.
10 11

Information for cooker hood
ENVIRONMENTAL PROTECTION:
This product is marked with the symbol on the selective sorting of waste electronic equipment. This
means that this product must not be disposed of with household waste but must be supported by a
system of selective collection in accordance with Directive 2002/96/EC. It will then be recycled or
dismantled to minimize impacts on the environment, electrical and electronic products are potentially
dangerous for the environment and human health due to the presence of hazardous substances.
For more information, please contact your local or regional authorities.
Note:
The following shows how to reduce total environmental impact (e.g. energy use) of the cooking process).
(13) Install the cooker hood in a proper place where there is efficient ventilation.
(14) Clean the cooker hood regularly so as not to block the airway.
(15) Remember to switch off the cooker hood light after cooking.
(16) Remember to switch off the cooker hood after cooking.
Information for dismantling
Do not dismantle the appliance in a way which is not shown in the user manual. The appliance could not be
dismantled by user. At the end of life, the appliance should not be disposed of with household waste. Check with
you Local Authority or retainer for recycling advice.
12

6. Troubleshooting
Failure
Root cause
Corrective action
No
power
1. Not plug-in or poor plug-
in.
2. Power socket is no
power.
3. Power supply dose not
connect with fuse or fuse
broken.
1. Plug-in perfect.
2. Connect with power supply or
contact electrician for after
service.
3. Replace fuse or call
electrician for after service.
No work
1. Power supply does not
work or voltage is not
stable.
2. No operation on fan
speed button.
1. Make sure power supply
works normally or call
eleclltricial for after service.
2. Press on fan speed button.
Light not
on
1. No operation on light
button.
2. The lamp is burnt down.
1. Press on light button.
2. Replace lamp (please call
service center)
Main
body
vabration
1. Main body mounting is
not stable.
2. Defective installation for
fan.
3. Defective fan
1. Make sure main body
mounting is stable enough.
2. Install fan correctly.
3. Replace fan (please call
service center
Poor
suction
1. When use hood, the
kitchen door and window
are openned too much or
close directly.
2. Hood installation height
is out of the range.
3. Hose is too long or too
much bend of hose.
1. Open or close door or window
to adjust suction.
2. Adjust hood installation height
as user manual.
3. Reduce length and bend of
hose.
4. Enlarge common venting hole
diameter to make sure the
damper of the hood can be
closed exactly.

1. Oil cup
Remove oil cup from card slot based on horizontal.
2. Filter
Remove screws to take out filter.
3. Hand-fasten nut
Clockwise rotate the nut to remove it.
4. Fan
Remove fan.

5. Chimney
Remove 4 screws, take out chimneys.
6. Cover sheet

Remove 4 screws to take out cover sheet.
7. Maintainence cover
Remove 12 screws to take out maintainence cover. Then repair fan and
motor.
8. Remove 8 screws from damper and 4
screws from air outlet. Then from reverse
side of body to remove one M5 screw.

9.LED light and switch control wire
Use flat screwdriver to remove LED light. Disconnect all responding wire
connectors for replacement.
10. Switch

Remove cover sheet and screws to take out switch.
Wiring Diagram