Haier HWM90-D0658 User manual

HWM90-D0658
se ' nalUrs ma u
This manual is for
Please read this manual
carefully before using.
Retain it for future reference.
Computerized Automatic
Saving Water Washing Machine
W0030806966A

CONTENTS
1
2
4
7
8
8
9
9
12
14
16
15
5
Safety precautions
Installation and adjustment
Names of the parts
Install the water inlet hose
Preparation before washing
Put in the laundries
Put in the detergent
Use the operation buttons
Close the top lid
Finish washing
Disposal after washing
Trouble-Shooting *Answer to question
Packing list *Specification

Names of the parts
1
Water inlet valve
Drain hose
Back cover
Power cord
Hook of fixing the drain hose
Power cord hook
Wash tub cover
Control panel seat
Cabinet
Cabinet handle
Pulsator
Top lid
Back control board
Control panel film
Inner tub
Lint Filter
Decoration label
Water absorption gasket
Base frame
Pulsator
Meaning and description of the symbols
Warning sign
Forbidden sign
Contents marked with that symbol are related to the safety
of the product and the personal safety of the users. Please
operate in strict conformity to the contents, otherwise it may
cause damage of the machine or injure the personal safety
of the user.
Contents marked with that symbol are actions forbidden to
perform. Performing of those actions may result in damage
of the machine or injure the personal safety of the user.
Tub
Lint filter（Installed by user)

12
The ventilation
holes at the bottom
Safety precautions
In case the washing machine is installed on ground
with carpet, be careful not to block the ventilation hole
with carpet.
Do not put the machine at damp place like the
bathroom. Never wash it with water. Do not
put wet laundries on the front control panel board.
Do not let the machine share one receptacle with other
electric appliances. If the power plug is damaged, or
the plugging into the receptacle is loose, do not use
the plug any more.
Do not wash water-proof laundry like the raincoat,
bike-covers, down textiles etc. To avoid abnormal
vibrations in spinning and damages to the laundries-
Do not bend, stretch, twist, bind the power cord by force, or reform it.
Do not press or clamp it with heavy items. If the power cord and power
plug are bad, or the receptacle is loose, be sure to have it replaced by
the technicians of our special shop or our agent, or the after-sales service
department to avoid any risk. Keep the prong of the power plug clean. If
dust is found on the power plug, please wipe it off with dry cloth.
In normal usage of the washing machine, the power
plug shall be ready to be pulled or plugged with hang.
Be sure to pull the plug off and close the water faucet
when occurring power failure, delivering the machine,
setting the machine idle or cleaning the machine, do
not plug or pull the power plug with wet hand.
Do not use water with temperature higher than 50℃
Please plug the plug on special 220V AC receptacle.
Be sure to use single-phase three pins receptacle.
Ensure the earthing prong of the power receptacle is
earthed reliably. Use leakage protector if possible.
Soft items

3
·Do not put hand into the rotating tub. It is dangerous
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing
machine to avoid them climbing on.
· Do not decompose, repair or alter the machine by
yourself.
·Do not put any hot or heavy items (such as the
kettle with hot water) on the washing machine.
·Do not wash laundry with volatile materials
(such as thinner, petrol etc.).
·e Handicapped or Children Without Care Shall Not
use the machine.
Th ·Keep the machine away from direct sunlight and
heat source like the heater.
Please keep the lint filter in good condition, and
install it to proper position during washing. If the
lint filter is lost or damaged, please contact the local
after-sales service department of our company.
dismantle install
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand, hairpin
and other foreign materials before washing.
Please check if the water faucet is open, and if the
connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
·
·
Safety precautions
Pel
tro
Thi n rne

安 装 位 置 的 调 整
4
Please install and adjust the machine according to the requirement of
the manual. It is very important to your security and correct
operating the machine.
Installation and adjustment
Overflow filter
Lint filter
After opening the package, please take out the lint
filter from the document bag, install it to the overflow
filter of the wash tub. See to the figure.
Install the lint filter
After opening the package, please lean the washing
machine gently down on soft items (like towel cloth,
blanket, etc.). Install the bottom plate to the bottom of
the machine with five screws by a cross screw driver,
then lift the machine up gently. See to the figure:
Bottom plate
Back
Front
Soft items
Screw
Install the bottom plate
Usage the drain hose
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be less than
10cm, or the drainage will not be smooth, and cost
such long time that the machine may stop at mid
way.
2. Do not step on or press the drain hose.
4.If extra drain hose is needed, please make separate
purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed
1.5m.
If the extra hose is too long, cut
it either at A or at B point.
AB
<10cm
A
> 30mm
<1.5m
3. If the drain hose is too long, cut it at mid point. To make
smooth drainage, cut the front end of the hose slantingly.
5.

5
Install the water inlet hose
Confirm the water faucet
The exit end face of the faucet
water faucet, suitable water faucet, not suitable
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
0m>1 m
Connection between the water inlet hose jointer
and the water faucet
2 Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
1.Press the lower end of the lock lever and push down the slider. Ta k e off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
3.Fasten the four screws evenly. See to Figure 4.
About 4mm before twisting
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut..(see to figure 6)
About less than 2mm after twisting
water inlet hose jointer
Screw knife
Screw
Bushing
Sign plate
Screw nut
water inlet hose
Figure 1
Figure 4
Figure 2
Figure 5
Figure 3
Figure 6
Slider
Lock level
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.

6
Connection between the water inlet hose and the washer
Dismantle the water inlet hose
Connection between the jointer of the water inlet hose
and the water inlet hose
Check the connection between the jointer of the water inlet
hose and the water faucet
1.Do not take off the water absorption cushion. Please check if the
cushion is dropped or damaged before each usage. If it happens
please contact our after-sale department immediately.
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
1.Push down the slider. Insert the water inlet hose into the jointer.
2 Hang the lock lever to the jointer. Release the slider till a click
sound is heard.
Locking level
Slider
water absorption
cushion.
nut of the water
inlet hose
the jointer of the
water inlet hose
Slider
Locking level
jointer of the
water inlet valve
1. Close the water faucet.
2. Press the locking lever. Push down the slider. Then pull of the water inlet
hose.
If the machine is used frequently, the jointer of the water inlet hose can be
kept
on the faucet to prevent damaging the fixing screw.
2 Put the nut of the water inlet hose on the valve jointer.
3 Fasten the nut. Swing it gently to confirm if it's suitable.
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.

7
1 Preparation before washing
Confirm if there's
special requirement
for the laundries.
Clear the pocket.
Take out the coins ,
sand,hairpins etc.
Fasten the buttons
and zippers.
When the pulsator is
running ,the buttons of
the laundries may cause
noise. For the sake of
discretion ,please put
the laundries with
buttons into other
laundries.
Preparation before washing
The quantity of the
laundries shall not
exceed the rated
value. The big
laundries like the
jeans shall be put
in loosely.
Pay attention to followings before washing the laundries
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries with infest color from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.

8
3 Put in the detergent
How to use the whitener
Fill water to decided level .Dilute the whitener with
container. Pour it slowly into the washing tub.
Avoid using whitener on laundries with colour or
pattern as they are prone to lose colour.
The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and
quantity of the whitener.
For powder whitener, please dissolve it before use.
How to use softener
2 Put in the laundries
The capacity of washing of the machine refer to
the largest weight of the standard laundries under
dry condition that can be washed in one time.
Laundries quantity in one washing cycle shall
be lower than the rated capacity. The largest
capacity of this machine is 9.0 kg.
The thickness ,size , type of the cloth will influence
the actual washing capacity. It is suitable to put in
reasonable amount of laundries and the laundries
can be turned round in washing for one time
washing.
Do not select the higher than "4" water level for
laundries less than 1.0kg ,so as to avoid splashing
of water.
See to the manual of softener for the usage
and dosage. When adding softener into the
softener inlet of washing powder box, note
that it shall not exceed the lower side of the cap.
Do not leave the softener for long period after
adding it into the box. Otherwise it may be
solidified and block the inlet.
As the softener is easy to solidify, please clean
the box frequently. (You shall clean it each time
you use reserve function).
Before use softener, you must select to sterilize
function.