Hallis Hudson Corded Wood Pole User manual

5mm
45mm Diameter 55mm Diameter
5mm
Pencil
Corded Wood Pole
Fitting Instructions
Tools you will need...
fit your corded wood pole...
Step 1: Mark your Screw Positions – these
vary by bracket type as follows:
Metal Brackets
Fit the brackets 5mm from each end of the
pole, this will be 25mm from the track (fig 1),
then screw the bracket button clockwise to
tighten (Fig 2).
With brackets attached, hold the pole to the
wall and, ensuring that the pole is level, mark
the screw positions (Fig.2).
DrillTape MeasureSpirit Level Screwdriver
METAL BRACKETS
CORDED WOOD POLE APPROXIMATE WEIGHT LIMITS
5mm 5mm 25mm
Fig.1 Fig.2
WOOD CLASP BRACKETS
Fig.4 Fig.5 Fig.6
Fig.3
Wood Clasp Brackets
(poles up to 210cm only)
Slide the brackets on to the pole and put them
5mm from each end of the pole (Fig.3).
Screw into the hole on the clasp bracket to
secure to the pole (Fig.4).
With the brackets attached, hold the pole in
your required position, ensuring the pole is level
and then draw around each of the bracket
bases.
Using the allen key provided unscrew the
backplate from the bracket (Fig.5).
Position the back plate in the centre of the
drawn circle ensuring the hole on the stem of
the backplate is facing upwards and mark the
screw positions (Fig.6).
WOOD ARCHITRAVE BRACKETS
5mm 50mm
Fig.7 Fig.8 Fig.9
Wood Architrave Brackets
(poles up to 210cm only)
FIt the brackets 5mm from each end of the
pole and this will be 50mm from the track
(Fig.7).
Screw into the hole in the bracket cup to secure
to the pole (Fig.8).
With brackets attached, hold the pole to the
wall and, ensuring that the pole is level, mark
the screw positions (Fig.9).
Bracket Type 45mm Pole Diameter 55mm Pole Diameter
Clasp, Metal and Wood Architrave Up to 2.7kg per metre Up to 4kg per metre
Recess Bracket Up to 3.5kg per metre Up to 5kg per metre
Allen Key

Step 3: Fitting Your Cord Tension Device
If using a White Nylon Tension Pulley: Using the
screws supplied fix the tension pulley to the wall
or window sill directly in line with the pull cord
(Fig.13).
Extend the neck of the pulley and secure in
higher position using a pin or small nail. Remove
the central barrel of the pulley by pulling it down
and then out (Fig.14).
Place the cord inside the pulley and replace the
barrel ensuring it clicks into place.
Remove the pin or nail from the pulley, the cord
should now be fully tensioned.
If the cord becomes twisted, rotate the head of
the pulley to untwist (Fig.15).
If using a Metal Tension Pulley: Pull the back
plate on the tensioner down, place against the
wall or window frame at least 150cm from the
floor and mark the screw holes. Fit to the wall
using the appropriate plugs and screws for your
wall type (Fig.16).
Use the Allen Key to open the top of the tensioner
and insert the cord (Fig.17). Close the top of the
tensioner and tighten.
Hallis Hudson Group Ltd,
Unit C34, Red Scar Business Park, Longridge Road, Preston, Lancashire, PR2 5NN
Sales Tel: [phone] | Sales Fax: [phone]
e-mail: [email protected] | www.halliswebshop.com
www.hallishudson.com
Young children can be strangled by loops in pull cords, chains,
tapes and inner cords that operate this product.
To avoid strangulation and entanglement, keep cords out of reach of
young children. Cords may become wrapped around a child’s neck.
Move beds, cots and furniture away from window covering cords.
Do not tie cords together. Make sure cords do not twist and create a loop.
WHITE NYLON TENSION PULLEY
WOOD RECESS BRACKETS
5A.2
Fig.13 Fig.14 Fig.15
METAL TENSION PULLEY
Fig.17Fig.16
25mm
Fig.10 Fig.11 Fig.12
Step 2: Fix the Brackets
Detach the pole from the brackets, if using clasp
brackets no need to remove the pole. Drill into
the marked positions and fit the brackets or
backplates to the wall.
If using Metal Brackets: Place the pole into the
brackets and tighten the screw plate on the front
of the bracket to secure the pole into position.
If using Clasp Brackets: Place pole and brackets
in to the backplate and secure the brackets to
the backplate by screwing the grub screw in to
the backplate using the allen key provided.
If using Recess Brackets: Screw the brackets on
to the backplate and place pole into position,
Secure the poles in to place by using the brass
screws supplied.
Always ensure that the correct screws and walls
plugs are used for your wall type.
Child Safety Warning: Installation of the cord
tensioner must be at a minimum of 150cm from
the floor. If you cannot fit the device at least
150cm from the floor with sufficient tension on
the cord, please contact the Sales Team for
assistance in shortening the cord.
Wood Recess Brackets
(poles up to 210cm only)
Slide the pole into the recess brackets and
secure by using the brass screws supplied, the
end of the bracket will be 25mm from the track
(Fig.10).
With brackets attached, hold the pole to the wall
and, ensuring that the pole is level, draw around
each bracket base (Fig.11).
Detach the back plate, position in the centre of
the drawn circle and mark the screw positions
(Fig.12).