Halma BEA PANTHER Series User manual

75.5172.03 20060608 1/2
PANTHER SERIES
PANTHER SERIES PANTHER SERIES
PANTHER SERIES
USER GUIDE
`
1
11
1
Mounting the pushplate:
LOCKING TAB
MOUNTING
KEYS
DOUBLE
GANG MOUNTING
HOLES
(TOP AND BOTTOM)
The Panther pushp ate may be mounted with or without the mounting
bracket. To use the mounting bracket, screw a minimum of two (2)
screws into a so id surface through the ho es in the mounting p ate (#8
countersunk head screws must be used). The mounting p ate must be
mounted so that the text side is facing up.
To attach the housing to the mounting p ate, p ace the housing over the
key tabs on the mounting p ate, and then s ide the p ate downward unti
the ocking tab engages the housing. To remove the housing, press in
the ocking tab and reverse this procedure.
NOTE: To secure y ock the p ate, put an additiona screw through both
the housing and the mounting p ate.
Hex Key
Housing Assemb y
Facep ate Assemb y
10EMR61 SHOWN
Dimensions
: 6 ¼” (160mm) Dia. x 1.5” (36mm) H
Weight : 1.2 bs (0.54 kg)
Material : ABS P astic and Stain ess Stee
Transmitter Frequency : 433 MHz
Certification : FCC
3 Installation
1 Description
2 Technical Specifications
We open up New Horizons
ENGAGE KEYS
LOCK/
UNLOCK

75.5172.03 20060608 2/2
2
Function:
To assemb e or disassemb e the pushp ate, use the enc osed hex key (or
simi ar diameter too ) to press in and re ease the spring c ips from the
facep ate bracket. The spring c ip wi need to be engaged/ disengaged
from top and bottom, one at a time. When the spring c ips are correct y
engaged, they wi make a click. It may be necessary to rotate the
facep ate s ight y to have them ock correct y.
To rep ace the battery, remove the facep ate and the four (4) screws
ho ding the battery cover to expose the transmitter assemb y. Rep ace
the battery with a fresh 12V, Type A23 battery and reassemb e the
pushp ate.
W RNING: DO NOT OVER TIGHTEN THE SCREWS ON THE
BATTERY COVER. THIS MAY CAUSE THE TRANSMITTER TO BE IN
CONSTANT ACTIVATION. THE HEAD OF THE SCREWS SHOULD
BE FLUSH WITH THE TOP OF THE PLASTIC COVER.
3
Tips
•Shut off all power going to the header before attempting any wiring procedures.
•Maintain a clean & safe environment when working in public areas.
•Constantly be aware of pedestrian traffic around the door area.
•Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.
•Always check placement of all wiring before powering up to insure that moving door parts will not catch any wires and cause damage
to equipment.
•Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.
4
Receiver Setup:
To program the receiver (pn 10RD433 sold separately), perform the following steps:
1. On the 433MHz digita receiver, press the brown earn button once (the ye ow LED wi i uminate).
2. Within 20 seconds, press the facep ate of the assemb ed pushp ate once (the ye ow LED on the receiver wi go out).
3. Press the facep ate again (the ye ow LED wi f ash for 2 seconds).
4. Press the facep ate again to verify receiver detection (the ye ow LED wi f ash and the red LED wi i uminate for the ength of time set by
the dipswitch).
NOTE: To c ear the memory of the receiver, press and ho d the earn button for 10 seconds.
For additional information about the receiver, please review the manual for the 10RD433 receiver.
4 Company Contact
BATTERY LOCATION
(OBSERVE PROPER POLARITY)
PRESS
(TOP AND THEN
BOTTOM)
DETACH/
REATTACH
(LISTEN FOR
CLICK)
Do not eave prob ems unreso ved. If a satisfactory so ution cannot be achieved after troub eshooting a prob em, p ease ca B.E.A.,
Inc. If you must wait for the fo owing workday to ca B.E.A., eave the door inoperab e unti satisfactory repairs can be made. Never
sacrifice the safe operation of the automatic door or gate for an incomp ete so ution.
The fo owing numbers can be ca ed 24 hours a day, 7 days a week. For more information, visit www.beainc.com.
West: 1-888-419-2564 Mid-West: 1-888-308-8843
South-East: 1-800-407-4545 North-East: 1-866-836-1863
US and Canada: 1-866-249-7937 Canada: 1-866-836-1863

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
---Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.