HALNy GPON ONT HL-4BX3V-F User manual

1Rev1.0-20231023
Quick Installation Guide
Quick Installation Guide
HALNy GPON ONT
HL-4BX3V-F

2Rev1.0-20231023
Quick Installation Guide
1 Safety guidance
1.1 Safety check
Before installing the device, you must check the following items.
1.1.1 Electric safety
Ensure that there are no inflammable, conductive or moist objects around.
Check whether the cables are aged and whether other electrical appliances
are placed stably.
check whether the alternating or direct input current is within the allowed range
of the device, whether the polarity of the direct current is correct, and whether
the earth line is properly connected.
1.1.2 Device position
Because the running electric device easily generates heat, please ensure to
place the device in a well-ventilated environment.
avoid direct sunshine and do not place the device on a PC case.
keep the device away from heat and water.
check whether power supply is available. The input voltage fluctuation range
must be smaller than 10%. The power plug should not share one socket with
a hair drier, an iron or a refrigerator.
1.2 Safety caution
Read the quick installation guide carefully before using the device.
note all cautions in the quick installation guide.
do not use any accessory that does not belong to the device without prior
consent of the manufacture, as it may cause fire or product damage.
use the power adapter accompanied in the package.
do not place any object on the device.
keep the device dry, ventilated, rainproof and clean.

3Rev1.0-20231023
Quick Installation Guide
during lightning weather, unplug the power plug and all connection cables, to
protect the device against lightning.
clean the device using a soft and dry cloth rather than liquid or atomizers.
Power off the device before cleaning it.
power off the idle device.
keep the ventilation hole clean and prevent any object from dropping into the
device through it. Otherwise, it may cause short circuit and further cause
device damage or fire. Do not spray liquid on the surface of the device.
do not open the case of the device, especially during device power-on,
before plugging or unplugging the power, ensure that the power is off, thus
avoiding surge.
be careful when unplugging the power, as the transformer may be very hot.
cover the optical interface with fiber interface cap when it is not in use. Avoid
direct eye exposure to the laser emitted from the optical interface. Wear safety
glasses if possible, to protect your eyes.
Please read the above safety guidance carefully before device use.
Users should assume responsibilities for any accidents due to
incompliance with the above instructions.
2 Overview
This chapter mainly describes functions and the structure of the device.
2.1 Features and Function
Fast rate. Support up to 1.25Gbps uplink and 2.5Gbps downlink data
transmission rates.
strong maintainability. Provide various statuses of LED indicators, to help
troubleshooting.
long transmission distance, up to 20 km.
Caution:

4Rev1.0-20231023
Quick Installation Guide
2.1 Front Panel
Fig1. Front Panel
On the front panel a row of LEDs is placed. Those LEDs allows you to easily check
the status of the device and it’s interfaces.
LED
Kolor
Status
Opis
POWER
Green
On
Power is ON.
Off
Power is OFF / Faulty PSU.
PON
Green
Blinks
Device detected by OLT.
On
Device registered by OLT.
LOS
Red
Blinks
No connection with OLT.
Off
Active connection with OLT.
NET
Green
On
Network access.
Off
No network access.
LAN1-3
Green
On
Ethernet link up.
Blinks
Data transmission.
Off
Ethernet link down.
2.5G
Green
On
Ethernet link up.
Blinks
Data transmission.
Off
Ethernet link down.
TEL
Green
On
VoIP account registered.
Blinks
Active call.
Off
VoIP account not registered.
2.4G
Green
On
WiFi interfaces enabled.
Blinks
Data transmission.
5G
Off
WiFi interfaces disabled.
WPS
Green
On
WPS enabled.
Blinks
Pairing in progres.
Off
WPS disabled.
Table 1.ONU LED indication table

5Rev1.0-20231023
Quick Installation Guide
LED
Kolor
Status
Opis
WPS
Green
On
Got WAN IP address successfully.
Blink
Connecting with controller.
Off
Device in bridged mode or no IP.
Table 2.ONU LED indication table for Easy Mesh agent mode
LED
Kolor
Status
Opis
2.4G
Green
On
The connection of Ethernet interface is normal.
Blink
Initialization of adding a agent.
Off
The connection of the Ethernet interface fails to establish.
5G
On
The connection of Ethernet interface is normal.
Blink
Initialization of adding a agent.
Off
The connection of the Ethernet interface fails to establish.
WPS
On
Pairing ok.
Blink
Initialization of adding a agent.
Off
Not activated/not triggered.
Table 3.ONU LED Indication Table for Easy Mesh contorller mode

6Rev1.0-20231023
Quick Installation Guide
2.2 Rear Panel
Fig2. Rear Panel
ONU rear panel description：
Function
ON/OFF
Device power ON/OFF button.
POWER
PSU socket.
RESET
Press and hold the button for at least 30 seconds (and no longer
than 40 seconds) to restore the device to factory settings.
WPS
Hold for 5s to activate WPS If MESH is enabled, press for 10
seconds to activate MESH pairing. In MESH mode, WPS paring is
disabled.
WIFI
Hold for 5s to activate/deactivate WiFi.
2.5G
Ethernet socket (RJ45).
LAN1-3
Ethernet socket (RJ45).
TEL
Phone socket (RJ11).
Table 4.Rear panel port description

7Rev1.0-20231023
Quick Installation Guide
3 ONU installation
The chapter describes therequired installation operations before you use the device
for the first time.
3.1 Product networking application - FTTH
Fiber to the Home (FTTH) means to install the ONU to residences or enterprise
buildings. The optical line terminal (OLT) is placed in the central equipment room.
The ONU can be placed in the home of a user, or it can provide connection for the
user through the Ethernet interface, according to the user requirement. The OLT
connects to the ONU with an optical distributor in the point-to-multipoint way. See
the following figure.
ONU can be placed in a room or the corridor. Because installation and
cabling in the corridor are relatively complex, let the professional
engineers deploy according to the actual situation. This manual
describes the procedure for installing the device at home, and is for
reference only.
Caution
:

8Rev1.0-20231023
Quick Installation Guide
3.2 Connecting ONU
3.2.1 Wiring connection and power on
1. Connect fiber optical cable (ended with AC/APC plug) to the optical port
located on the bottom of the device.
2. You can connect an Ethernet devices to LAN1-LAN3 or 2.5G sockets
(ex.computer with wired NIC, printer, gaming console, set-top-box, TV,
etc.)
3. You can connect a phone to TEL socket
4. Plug in the PSU plug to the POWER socket. Before you install the PSU
please make sure the ON/OFF button is in OFF position
5. Connect the PSU to the power grid socket
6. Turn on the device by pressing the ON/OFF button.
When a fiber is not in use, ensure to cover the optical interface of the ONU
and the dust cap of the optical fiber. Prevent grease, dust pollution or water
immersion, which may lead to unavailable fiber and optical interface of the
device. If fibers need to be fixed or bended during cabling, do not fasten the
fibers too tight. Avoid fiber extrusion, which may lead to increase of fiber
material or unavailable fiber.
Caution
:

9Rev1.0-20231023
Quick Installation Guide
4 Troubleshooting
Symptom
Solution
The POWER
indicator is not on


Check whether the power connection is correct,
check whether the power adapter matches the
device.
The PON indicator is
not on


Check whether the SN of ONU matches OLT,
check whether the optical attenuation is in the normal
range.
The LOS indicator is
not on

Check whether the optical fiber cable is properly
inserted,

check whether the optical fiber connector is clean.
The LAN and 2.5G
indicators are not on



Check whether the PC NIC is enabled,
check whether the network cables included in the
device package are used,
check whether the network cable connection is
normal,

check whether the LED for your corresponding LAN
or 2.5G port is on,

check whether the network adapter works in the
normal state.

10 Rev1.0-20231023
Quick Installation Guide
5 Technical specification
Main technical specifications
Standard
GPON
ITU-T G.984
Rate
Uplink
1.25Gbps
Downlink
2.5Gbps
Interface
1 WAN port
SC/APC, Single Mode optical fiber
1 2.5G port
2500Base-T (RJ45)
3 LAN ports
RJ-45 10/100/1000Mbps, auto-MDI/MDIX
1 POTS port
RJ-11 FXS
WiFi 2.4Ghz
WiFi 5Ghz
802.11n/ax (2T2R MIMO) 576Mbps
802.11ac/ax (2T3R MIMO) 2402Mbps
Physical characteristics and environment requirements
Power adapter input
100V～240V AC，50Hz～60Hz
Whole-device power supply
12V DC，1.5A
Standard power consumption
<18W
Operating temperature
0˚C～45˚C
Operating humidity
10%~90% (non-condensing)
Dimension
L x W x H：225mm x 142mm x 46mm
Weight
<500g
Appendix a acronyms and abbreviations
GPON
Gigabit Passive Optical Network
FTTB
Fiber to the Building
FTTH
Fiber to the Home
OLT
Optical Line Terminal
ONU
Optical Network Unit
PON
Passive Optical Network

11 Rev1.0-20231023
Quick Installation Guide
Additional information:
Declaration of conformity (CE)
This device has been tested and found to comply with the stated standards
which are required by the Council Directive of 2014/30/EU. The device
complies with this CE Declaration when the installation is done in
accordance with the instruction and documentation. The importer don’t take
responsibility for any issues caused by improper use of the device.
The full document is on below web page and it is available in importer:
CE / warranty terms and conditions:
www.halny.com
Importer:
FIBRAIN Sp. z o.o
36-062 Zaczernie 190F (POLAND) in[email protected]
Information furnished by HALNy Networks is believed to be accurate and
reliable. However, no responsibility is assumed by importer for its use, nor
for any infringements of patents or other rights of third parties which may
result from its use. No license is granted by implication or otherwise under
any patent or patent rights of the manufacturer. Manufacturer reserves the
rights to change specifications at any time without notice.

12 Rev1.0-20231023
Quick Installation Guide
Recycling This product bears the selective sorting
symbol for Waste electrical and electronic
equipment (WEEE). This means that this product
must be handled according toEuropean directive
2012/19/EU in order to be recycled or
dismantled. This will minimize the negative
effects on the environment and human health
resulting from the possibility of the presence in
the equipment substances, mixtures and
hazardous components. A user can give the
product to a competent recycling organization, to WEEE collection points or
to a distributor (in accordance with local regulations).