HALNy HL-4GXV-F User manual

Quick Installation Guide
1
Quick Installation Guide
HALNy GPON ONT
HL-4GXV-F

Quick Installation Guide
2
1 Safety Guidance
1.1 Safety Check
Before installing the device, you must check the following items.
1.1.1 Electric Safety
⚫Ensure that there are no inflammable, conductive or moist objects around.
Check whether the cables are aged and whether other electrical appliances
are placed stably,
⚫Check whether the alternating or direct input current is within the allowed
range of the device, whether the polarity of the direct current is correct, and
whether the earth line is properly connected.
1.1.2 Device Position
⚫Because the running electric device easily generates heat, please ensure to
place the device in a well-ventilated environment,
⚫Avoid direct sunshine, and do not place the device on a PC case,
⚫Keep the device away from heat and water,
⚫Check whether power supply is available. The input voltage fluctuation range
must be smaller than 10%. The power plug should not share one socket with
a hair drier, an iron or a refrigerator.
1.2 Safety Caution
⚫Read the quick installation guide carefully before using the device,
⚫Note all Cautions in the quick installation guide,
⚫Do not use any accessory that does not belong to the device without prior
consent of the manufacture, as it may cause fire or product damage,
⚫Use the power adapter accompanied in the package,
⚫Do not place any object on the device,
⚫Keep the device dry, ventilated, rainproof, and clean,
⚫During lightning weather, unplug the power plug and all connection cables, to
protect the device against lightning,

Quick Installation Guide
3
⚫Clean the device using a soft and dry cloth rather than liquid or atomizers.
Power off the device before cleansing it,
⚫Power off the idle device,
⚫Keep the ventilation hole clean and prevent any object from dropping into the
device through it. Otherwise, it may cause short circuit and further cause
device damage or fire. Do not spray liquid on the surface of the device,
⚫Do not open the case of the device, especially during device power-on,
⚫Before plugging or unplugging the power, ensure that the power is off, thus
avoiding surge,
⚫Be careful when unplugging the power, as the transformer may be very hot,
⚫Cover the optical interface with fiber interface cap when it is not in use. Avoid
direct eye exposure to the laser emitted from the optical interface. Wear safety
glasses if possible, to protect your eyes.
Caution:
Please read the above safety guidance carefully before device use.
Users should assume responsibilities for any accidents due to
incompliance with the above instructions.
2 Overview
This chapter mainly describes functions and the structure of the device.
2.1 Features and Function
⚫Fast rate. Support up to 1.25Gbps uplink and 2.5Gbps downlink data
transmission rates,
⚫Strong maintainability. Provide various statuses of LED indicators, to help
troubleshooting,
⚫Long transmission distance, up to 20 km.

Quick Installation Guide
4
2.1 Front panel
Fig1. Front panel
On the front panel a row of LEDs is placed. Those LEDs allows you to easily check
the status of the device and it’s interfaces.
LED
Kolor
Status
Opis
POWER
Green
On
Power is ON
Off
Power is OFF / Faulty PSU
PON
Green
Blinks
Device detected by OLT
On
Device registered by OLT
LOS
Czerwony
Blinks
No connection with OLT
Off
Active connection with OLT
NET
Green
On
Network access
Off
No network access
LAN4-1
Green
On
Ethernet link up
Blinks
Data transmission
Off
Ethernet link down
TEL
Green
On
VoIP account registered
Blinks
Active call
Off
VoIP account not registered
2.4G
Green
On
WiFi interfaces enabled
Blinks
Data transmission
5G
Off
WiFi interfaces disabled
WPS
Green
On
WPS enabled
Blinks
Pairing in progress
Off
WPS disabled

Quick Installation Guide
5
2.2 Rear panel
Fig2. Rear panel
Function
POWER
PSU socket
LAN 1..4
Ethernet socket (RJ45)
TEL
Phone socket (RJ11)
ON/OFF
Device power ON/OFF button
WPS
Hold for 5s to activate WPS
RESET
Hold for 30-40s to restore device to factory settings
WIFI
Hold for 5s to activate/deactivate WiFi
SLIDER 1..4
1-3
Front panel LEDs active
4
Front panel LEDs inactive

Quick Installation Guide
6
3 ONU installation
The chapter describes the required installationoperations before you use the device
for the first time.
3.1 Product Networking Application - FTTH
Fiber to the Home (FTTH) means to install the ONU to residences or enterprise
buildings. The optical line terminal (OLT) is placed in the central equipment room.
The ONU can be placed in the home of a user, or it can provide connection for the
user through the Ethernet interface, according to the user requirement. The OLT
connects to the ONU with an optical distributor in the point-to-multipoint way. See
the following figure.
Caution:
The ONU applies to installation at home or in the corridor. Because
installation and cabling in the corridor are relatively complex, let the
professional engineers deploy according to the actual situation. This
manual describes the procedure for installing the device at home, and
is for reference only.

Quick Installation Guide
7

Quick Installation Guide
8
3.2 Connecting ONU
3.2.1 Wiring connection and power on
1. Connect fiber optical cable (ended with AC/APC plug) to the optical port
located on the bottom of the device.
2. You can connect an Ethernet devices to LAN1 … LAN4 sockets (ex.
computer with wired NIC, printer, gaming console, set-top-box, TV, etc.)
3. You can connect a phone to TEL socket
4. Plug in the PSU plug to the POWER socket. Before you install the PSU
please make sure the ON/OFF button is in OFF position
5. Connect the PSU to the power grid socket
6. Turn on the device by pressing the ON/OFF button.

Quick Installation Guide
9
Caution:
When a fiber is not in use, ensure to cover the optical interface of the ONU
and the dust cap of the optical fiber. Prevent grease, dust pollution or water
immersion, which may lead to unavailable fiber and optical interface of the
device. If fibers need to be fixed or bended during cabling, do not fasten the
fibers too tight. Avoid fiber extrusion, which may lead to increase of fiber
material or unavailable fiber.
4 Troubleshooting
Symptom
Solution
The POWER
indicator is not on
Check whether the power connection is correct,
Check whether the power adapter matches the
device.
The PON indicator is
not on
Check whether the SN of ONU matches OLT,
Check whether the optical attenuation is in the normal
range.
The LOS indicator is
not on
Check whether the optical fiber cable is properly
inserted,
Check whether the optical fiber connector is clean.
The LAN indicators
are not on
Check whether the PC NIC is enabled,
Check whether the network cables included in the
device package are used,
Check whether the network cable connection is
normal,
Check whether the indicator ofthe network adapter is
on,
Check whether the network adapter works in the
normal state.

Quick Installation Guide
10
5 Technical Specification
Main Technical Specifications
Standard
GPON
ITU-T G.984, TR156/TR255
WAN
Throughput
Uplink
1.25Gbps
Downlink
2.5Gbps
Interface
1 WAN port
SC/APC, Single Mode optical fiber
4 LAN ports
RJ-45 10/100/1000Mbps, auto-MDI/MDIX
1 POTS port
RJ-11 FXS
WiFi 2.4Ghz
WiFi 5Ghz
802.11n/ax (2T2R MIMO) 576Mbps
802.11ac/ax (2T2R MIMO) 1201Mbps
Physical Characteristics and Environment Requirements
Power adapter input
100V～240V AC，50Hz～60Hz
Whole-device power supply
12V DC，1.5A
Standard power consumption
<18W
Operating temperature
-5˚C～45˚C
Operating humidity
5%~95% (non-condensing)
Dimension
L x W x H：225mm x 143mm x 47mm
Weight
<500g
Appendix A Acronyms and Abbreviations
GPON
Gigabit Passive Optical Network
FTTB
Fiber to the Building
FTTH
Fiber to the Home
OLT
Optical Line Terminal
ONU
Optical Network Unit
PON
Passive Optical Network

Quick Installation Guide
11
Additional information:
Declaration of Conformity (CE)
HL-4GXV-F has been tested and found to comply with the stated standards
which are required by the Council Directive of 2014/30/EU. The device
complies with this CE Declaration when the installation is done in
accordance with the instruction and documentation. The importer don’t take
responsibility for any issues caused by improper use of the device.
The full document is on below web page and it is available in importer:
CE / warranty terms and conditions:
www.halny.com
Importer:
FIBRAIN Sp. z o.o
36-062 Zaczernie 190F (POLAND)
[email protected]
Information furnished by HALNy Networks is believed to be accurate and
reliable. However, no responsibility is assumed by importer for its use, nor
for any infringements of patents or other rights of third parties which may
result from its use. No license is granted by implication or otherwise under
any patent or patent rights of the manufacturer. Manufacturer reserves the
rights to change specifications at any time without notice.

Quick Installation Guide
12
Recycling This product bears the selective sorting
symbol for Waste electrical and electronic
equipment (WEEE). This means that this product
must be handled according to European directive
2012/19/EU in order to be recycled or
dismantled. This will minimize the negative
effects on the environment and human health
resulting from the possibility of the presence in
the equipment substances, mixtures and
hazardous components. A user can give the
product to a competent recycling organization, to WEEE collection points or
to a distributor (in accordance with local regulations).