HALNy HL-2BV User manual

Quick Installation Guide
GPON ONT
HALNY HL-2BV

HALNy HL-2BV Quick Installation Guide
2
Safety Guidance
1.1 Safety Check
Before installing the device, you must check the following items.
1.1.1 Electric Safety
⚫Ensure that there are no inflammable, conductive or moist objects around.
Check whether the cables are aged and whether other electrical appliances
are placed stably,
⚫Check whether the alternating or direct input current is within the allowed
range of the device, whether the polarity of the direct current is correct, and
whether the earth line is properly connected.
1.1.2 Device Position
⚫Because the running electric device easily generates heat, please ensure to
place the device in a well-ventilated environment,
⚫Avoid direct sunshine, and do not place the device on a PC case,
⚫Keep the device away from heat and water,
⚫Check whether power supply is available. The input voltage fluctuation range
must be smaller than 10%. The power plug should not share one socket with
a hair drier, an iron or a refrigerator.
1.2 Safety Caution
⚫Read the quick installation guide carefully before using the device,
⚫Note all Cautions in the quick installation guide,
⚫Do not use any accessory that does not belong to the device without prior
consent of the manufacture, as it may cause fire or product damage,
⚫Use the power adapter accompanied in the package,
⚫Do not place any object on the device,
⚫Keep the device dry, ventilated, rainproof, and clean,
⚫During lightning weather, unplug the power plug and all connection cables, to
protect the device against lightning,
⚫Clean the device using a soft and dry cloth rather than liquid or atomizers.
Power off the device before cleansing it,

HALNy HL-2BV Quick Installation Guide
3
⚫Power off the idle device,
⚫Keep the ventilation hole clean and prevent any object from dropping into the
device through it. Otherwise, it may cause short circuit and further cause
device damage or fire. Do not spray liquid on the surface of the device,
⚫Do not open the case of the device, especially during device power-on,
⚫Before plugging or unplugging the power, ensure that the power is off, thus
avoiding surge,
⚫Be careful when unplugging the power, as the transformer may be very hot,
⚫Cover the optical interface with fiber interface cap when it is not in use. Avoid
direct eye exposure to the laser emitted from the optical interface. Wear safety
glasses if possible, to protect your eyes.
Caution:
Please read the above safety guidance carefully before device use.
Users should assume responsibilities for any accidents due to
incompliance with the above instructions.
2 Overview
This chapter mainly describes functions and the structure of the HALNy HL-2BV.
2.1 Features and Function
⚫Fast rate. Support up to 1.25Gbps uplink and 2.5Gbps downlink data
transmission rates,
⚫Strong maintainability. Provide various statuses of LED indicators, to help
troubleshooting,
⚫Long transmission distance, up to 20 km.
2.2 Front and Rear Panel
The description of the front panel and the rear panel of the GPON ONU as follows.

HALNy HL-2BV Quick Installation Guide
4
2.2.1 Front Panel
Fig. 1 - Front Panel
LED
Color
Status
Description
PWR
Green
On
The power works normally.
Off
Powered off or the power supply is abnormal.
PON
Green
Refer to Table 2: “PON LED Status Instruction”
LOS
Red
Refer to Table 2: “PON LED Status Instruction”
LAN1
2.5G
Green
On
The connection of Ethernet interface is normal.
Blink
Data is being transmitted through the Ethernet interface.
Off
The connection of the Ethernet interface fails to
establish.
TEL
Green
On
Voip account is registered
Blink
Phone call
Off
Port deactivated or Voip account is unregistered
Table 1. ONU LED Indication Table
Table 2.PON LED Status Instruction
PON LED Status Instruction
PON
LOS
Description
Off
Off
The ONT is disabled by the OLT
Flash
Off
The ONT is registering to the OLT
On
Off
The ONT has already registered to OLT
Off
Flash
The fiber is not connected properly

HALNy HL-2BV Quick Installation Guide
5
2.2.2 Rear Panel
Fig 2. Rear Panel
ONU Rear Panel Description：
Interface /
Button
Function
LAN1
2.5G
Ethernet interface, for connecting to a computer or an Ethernet
interface of a switch.
Reset
Press the button for 10 seconds to reboot ONU and restore the
factory default configurations.
Power
Connect power cable
ON/OFF
Turn on/off the power supply.
TEL1
RJ-11 Telephone Port
Table 3.Rear Panel port description

HALNy HL-2BV Quick Installation Guide
6
3 ONU Installation
The chapter describes the required installation operations before youuse the device
for the first time.
3.1 Product Networking Application - FTTH
Fiber to the Home (FTTH) means to install the ONU to residences or enterprise
buildings. The optical line terminal (OLT) is placed in the central equipment room.
The ONU can be placed in the home of a user, or it can provide connection for the
user through the Ethernet interface, according to the user requirement. The OLT
connects to the ONU with an optical distributor in the point-to-multipoint way. See
the following figure.
FTTH
Note：
The ONU applies to installation at home or in the corridor. Because installation and
cabling in the corridor are relatively complex, let the professional engineers deploy
according to the actual situation. This manual describes the procedure for installing the
device at home, and is for reference only.
3.2 Installation Preparations
The Ethernet interface of your computer connects to the Ethernet interface of the
ONU. Before installing it, ensure that anEthernet adapteris already installed inyour
computer.

HALNy HL-2BV Quick Installation Guide
7
3.3 Connecting ONU
3.3.1 Connecting the Network Cable
Step 1 Use the one end of the network cable to connect the Ethernet interface of
the computer.
Step 2 Use other end of a network cable to connect the Ethernet interface on the
rear panel of the HALNy HL-2BV.
3.3.2 Connecting the Fiber
Caution:
⚫When a fiber is not in use, ensure to cover the optical interface of the ONU and
the dust cap of the optical fiber. Prevent grease, dust pollution or water
immersion, which may lead to unavailable fiber and optical interface of the
device.
⚫If fibers need to be fixed or bended during cabling, do not fasten the fibers too
tight. Avoid fiber extrusion, which may lead to increase of fiber material or
unavailable fiber.

HALNy HL-2BV Quick Installation Guide
8
3.3.3 Connecting the Power Adapter and Power Cord
⚫Connect the output end of the power adapter included in the device package to
the input end of the power supply of the ONU ,
⚫Insert one end of the power cord attached with the device into the input end of
the power adapter. Insert the other end of the power cord into the power socket,
⚫Check whether the Power indicator is on. If it is on, the power supply is normal.
Otherwise, check whether the power cord and the power adapter are correctly
connected.
4 Troubleshooting
Symptom
Solution
The POWER
indicator is not on
Check whether the power connection is correct,
Check whether the power adapter matches the
device.
The PON indicator is
not on
Check whether the SN of ONU matches OLT,
Check whether the optical attenuation is in the normal
range.
The LOS indicator is
not on
Check whether the optical fiber cable is properly
inserted,
Check whether the optical fiber connector is clean.
The LAN / 2.5G
indicators are not on
Check whether the PC NIC is enabled,
Check whether the network cables included in the
device package are used,
Check whether the network cable connection is
normal,
Check whether the indicator ofthe network adapter is
on,
Check whether the network adapter works in the
normal state.

HALNy HL-2BV Quick Installation Guide
9
5 Technical Specification
Main Technical Specifications
Standard
GPON Standard
ITU-T G.984.x and G.988
Rate
Uplink
1.25Gbps
Downlink
2.5Gbps
Interface
Optical interface
Single Mode
LAN port
RJ-45 10/100/1000Mbps MDI/MDIX Self
adaption
2.5G port
RJ-45 100/1000/2500Mbps MDI/MDIX Self
adaption
POTS port
RJ-11 FXS
Physical Characteristics and Environment Requirements
Power adapter input
100V～240V AC，50Hz～60Hz
Whole-device power supply
12V DC / 2A
Standard power consumption
<24W
Operating temperature
0˚C～45˚C
Operating humidity
10%~90% (non-condensing）
Dimension
L x W x H：112mm x 162mm x 42mm
Weight
<500g
Appendix A Acronyms and Abbreviations
GPON
Gigabit Passive Optical Network
FTTB
Fiber to the Building
FTTH
Fiber to the Home
OLT
Optical Line Terminal
ONU
Optical Network Unit
PON
Passive Optical Network

HALNy HL-2BV Quick Installation Guide
10
Additional information:
Declaration of Conformity (CE and FCC)
This device has been tested and found to comply with the stated standards
which are required by the Council Directive of 2014/30/EU and Part 15,
subpart B of FCC Rules. The device complies with this CE and FCC
Declaration when the installation is done in accordance with the instruction
and documentation. The importer don’t take responsibility for any issues
caused by improper use of the device.
Documents are available on below web page or upon contact with importer:
CE / warranty terms and conditions:
www.halny.com
Importer:
FIBRAIN Sp. z o.o
36-062 Zaczernie 190F (POLAND)
[email protected]
Information furnished by HALNy Networks is believed to be accurate and
reliable. However, no responsibility is assumed by importer for its use, nor
for any infringements of patents or other rights of third parties which may
result from its use. No license is granted by implication or otherwise under
any patent or patent rights of the manufacturer. Manufacturer reserves the
rights to change specifications at any time without notice.

HALNy HL-2BV Quick Installation Guide
11
Recycling This product bears the selective sorting
symbol for Waste electrical and electronic
equipment (WEEE). This means that this product
must be handled according to European directive
2012/19/EU in order to be recycled or
dismantled. This will minimize the negative
effects on the environment and human health
resulting from the possibility of the presence in
the equipment substances, mixtures and
hazardous components. A user can give the
product to a competent recycling organization, to WEEE collection points or
to a distributor (in accordance with local regulations).