Halo Rollover occupant protection system User manual

Maintenance and Inspection Records

Safety Engineering International recommends monthly

inspections of your HALO™. For your convenience we have

included a starting record below. We suggest to check all

welds for security. Contact your dealer to report any

problems. Record inspection notes and initials on the

following form:

Month Day Year Inspected by Notes

________________________________________________

Read User’s Manual Completely Before Use

User Manual

Maintenance and Inspection Records

Safety Engineering International recommends monthly

inspections of your HALO™. For your convenience we have

included a starting record below. We suggest to check all

welds for security. Contact your dealer to report any

problems. Record inspection notes and initials on the

following form:

Month Day Year Inspected by Notes

________________________________________________

Read User’s Manual Completely Before Use

User Manual

HALO™

User Manual

User’s Record:

To provide quality consumer service and technical support, it

is suggested that you keep the following information as well

as receipt of purchase.

Date of Purchase: _________________________________

Location of Purchase:______________________________

Serial Number:____________________________________

Please read the disclaimer/warranty information before

proceeding.

Table of Contents

Pg. 3 Product Disclaimer

Pg. 4 Warnings & Light Placement

Pg. 5-7Warranty

Pg. 8 Maintenance Record

All product inquiries for the HALO™ should be

directed to:

Safety Engineering International

[email protected] (805) 895-5192

WARRANTY & Other Legal Information

Work By Others; Safety Devices.

SEI has no responsibility for labor or work performed by

Buyer or others once certified installation is complete. Buy-

er is solely responsible for furnishing and requiring its em-

ployees and customers to use all safety devise guards and

safe operating procedures required by law and/or as set forth

in the user manual furnished by Safety Engineering Interna-

tional.

Governing Law/Venue.

This Agreement shall be construed and governed under the

laws of the State of California, U.S.A, without application of

conflict of law principles. Each party agrees that all actions

or proceedings arising out of or in connection with this

Agreement shall be commenced, tried, and litigated only in

the state courts sitting in Santa Barbara, California or the

U.S. Federal Court for California, U.S.A..

Each party waives any right it may have to assert the doc-

trine of “forum non conveniens” or to object to venue to the

extent that any proceeding is brought in accordance with this

section. Each party consents to and waives any objection to

the exercise of personal jurisdiction over it by courts de-

scribed in this section.

EACH PARTY WAIVES TO THE FULLEST EXTENT

PERMITTED BY APPLICABLE LAW THE RIGHT TO A

TRIAL BY JURY.

HALO™

User Manual

User’s Record:

To provide quality consumer service and technical support, it

is suggested that you keep the following information as well

as receipt of purchase.

Date of Purchase: _________________________________

Location of Purchase:______________________________

Serial Number:____________________________________

Please read the disclaimer/warranty information before

proceeding.

Table of Contents

Pg. 3 Product Disclaimer

Pg. 4 Warnings & Light Placement

Pg. 5-7 Warranty

Pg. 8 Maintenance Record

All product inquiries for the HALO™ should be

directed to:

Safety Engineering International

info@safetyei.com (805) 683-6835

WARRANTY & Other Legal Information

Work By Others; Safety Devices.

SEI has no responsibility for labor or work performed by

Buyer or others once certified installation is complete. Buy-

er is solely responsible for furnishing and requiring its em-

ployees and customers to use all safety devise guards and

safe operating procedures required by law and/or as set forth

in the user manual furnished by Safety Engineering Interna-

tional.

Governing Law/Venue.

This Agreement shall be construed and governed under the

laws of the State of California, U.S.A, without application of

conflict of law principles. Each party agrees that all actions

or proceedings arising out of or in connection with this

Agreement shall be commenced, tried, and litigated only in

the state courts sitting in Santa Barbara, California or the

U.S. Federal Court for California, U.S.A..

Each party waives any right it may have to assert the doc-

trine of “forum non conveniens” or to object to venue to the

extent that any proceeding is brought in accordance with this

section. Each party consents to and waives any objection to

the exercise of personal jurisdiction over it by courts de-

scribed in this section.

EACH PARTY WAIVES TO THE FULLEST EXTENT

PERMITTED BY APPLICABLE LAW THE RIGHT TO A

TRIAL BY JURY.

WARRANTY & Other Legal Information

EXCLUSION OF OTHER WARRANTIES.

THE FOREGOING LIMITED WARRANTY IS IN LIEU

OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED. ANY AND ALL OTHER EXPRESS,

STATUTORY OR IMPLIED WARRANTIES,

INCLUDING BUT NOT LIMITED TO, ANY

WARRANTY OF MERCHANTABILITY OR FITNESS

FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY

DISCLAIMED. NO WARRANTY IS MADE WHICH

EXTENDS BEYOND THAT WHICH IS EXPRESSLY

CONTAINED HEREIN.

LIMITATION OF LIABILITY.

IN NO EVENT SHALL SAFETY ENGINEERING

INTERNATIONAL BE LIABLE TO BUYER OR ANY

OTHER PARTY FOR ANY INCIDENTAL,

CONSEQUENTIAL OR SPECIAL DAMAGES

(INCLUDING, WITHOUT LIMITATION, LOST

PROFITS OR DOWN TIME) ARISING FROM OR IN

ANY MANNER CONNECTED WITH THE HALO™,

ANY BREACH BY SAFETY ENGINEERING

INTERNATIONAL OR ITS AGENTS OF THIS

AGREEMENT, OR ANY OTHER CAUSE

WHATSOEVER, WHETHER BASED ON CONTRACT,

TORT OR ANY OTHER THEORY OF LIABILITY.

BUYER’S REMEDY WITH RESPECT TO ANY CLAIM

ARISING UNDER THIS AGREEMENT IS STRICTLY

LIMITED TO NO MORE THAN THE AMOUNT PAID

BY THE BUYER FOR THE HALO™.

Product Disclaimer

The use and intention of your HALO™RDMD product is to

minimize roof damage should a vehicle rollover occur and is

designed for specific makes and models of vehicles only.

Although this product is designed to reduce or lessen roof

deformation in a rollover, the HALO™roll hoop is not a

structural reinforcement. Pillar modifications or enhance-

ments can be done separately or in conjunction with the in-

stallation of the HALO™to provide additional roof structure

reinforcement. However, some reasonably foreseeable im-

pact may exceed the product's capability to protect against

injury. There are limitations to the severity of impact that the

product sold herein can withstand and this product is not a

substitution for safe and careful driving. Seat belts and any

other vehicle equipped safety devices MUST be in use

and working at all times. In the case in which a rollover

accident has occurred, the product must be replaced and is

not intended for repeat use.

This product is not intended to be a roof rack and should not

be used as an attachment point for anything other than light-

ing. Guidelines for lighting attachments are outlined in the

next section. This product is not a storage area. Do not store

items in, under, or on top of your HALO™, as this might

interfere with its operation in a rollover. Installation of this

product must follow the guidelines found in the installation

manual, if applicable. Only the fasteners and proper attach-

ment points found in the installation manual should be used

and installed only by a certified installer.

WARRANTY & Other Legal Information

EXCLUSION OF OTHER WARRANTIES.

THE FOREGOING LIMITED WARRANTY IS IN LIEU

OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED. ANY AND ALL OTHER EXPRESS,

STATUTORY OR IMPLIED WARRANTIES,

INCLUDING BUT NOT LIMITED TO, ANY

WARRANTY OF MERCHANTABILITY OR FITNESS

FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY

DISCLAIMED. NO WARRANTY IS MADE WHICH

EXTENDS BEYOND THAT WHICH IS EXPRESSLY

CONTAINED HEREIN.

LIMITATION OF LIABILITY.

IN NO EVENT SHALL SAFETY ENGINEERING

INTERNATIONAL BE LIABLE TO BUYER OR ANY

OTHER PARTY FOR ANY INCIDENTAL,

CONSEQUENTIAL OR SPECIAL DAMAGES

(INCLUDING, WITHOUT LIMITATION, LOST

PROFITS OR DOWN TIME) ARISING FROM OR IN

ANY MANNER CONNECTED WITH THE HALO™,

ANY BREACH BY SAFETY ENGINEERING

INTERNATIONAL OR ITS AGENTS OF THIS

AGREEMENT, OR ANY OTHER CAUSE

WHATSOEVER, WHETHER BASED ON CONTRACT,

TORT OR ANY OTHER THEORY OF LIABILITY.

BUYER’S REMEDY WITH RESPECT TO ANY CLAIM

ARISING UNDER THIS AGREEMENT IS STRICTLY

LIMITED TO NO MORE THAN THE AMOUNT PAID

BY THE BUYER FOR THE HALO™.

Product Disclaimer

The use and intention of your HALO™RDMD product is to

minimize roof damage should a vehicle rollover occur and is

designed for specific makes and models of vehicles only.

Although this product is designed to reduce or lessen roof

deformation in a rollover, the HALO™roll hoop is not a

structural reinforcement. Pillar modifications or enhance-

ments can be done separately or in conjunction with the in-

stallation of the HALO™to provide additional roof structure

reinforcement. However, some reasonably foreseeable im-

pact may exceed the product's capability to protect against

injury. There are limitations to the severity of impact that the

product sold herein can withstand and this product is not a

substitution for safe and careful driving. Seat belts and any

other vehicle equipped safety devices MUST be in use

and working at all times. In the case in which a r ollover

accident has occurred, the product must be replaced and is

not intended for repeat use.

This product is not intended to be a roof rack and should not

be used as an attachment point for anything other than light-

ing. Guidelines for lighting attachments are outlined in the

next section. This product is not a storage area. Do not store

items in, under, or on top of your HALO™, as this might

interfere with its operation in a rollover. Installation of this

product must follow the guidelines found in the installation

manual, if applicable. Only the fasteners and proper attach-

ment points found in the installation manual should be used

and installed only by a certified installer.

Lighting Placement on HALO™

Lighting may be placed on your HALO™but

should be attached with a removable fastener.

Do not weld your lighting fixture to your

HALO™.

Do not fasten lighting fixtures to the roll hoop

(circular tube spanning from passenger to driver

side).

Product Warnings

Do not weld anything to your HALO™.

Do not attach anything other than Lighting.

Do not use as a roof rack or storage device.

Do not move HALO™to another vehicle.

Do not use as an anchor for a winch or other lift-

ing, hauling or pulling.

If your vehicle is in an accident, please contact

your dealer so that the HALO™can be

reexamined for any structural failures.

Note: Any inspection costs occur at owner’s

expense.

WARRANTY & Other Legal Information

Inspection & Acceptance. Buyer shall inspect the HALO within a rea-

sonable period of time after delivery, not to exceed ten (10 days). If Buyer

rejects the HALO, Buyer must immediately contact Safety Engineering

International (SEI). If the HALO is defective Buyer will be given a Return

Authorization Number (“RAN”) before returning the HALO to SEI.

HALO returned without a RAN will be refused. SEI will not be responsi-

ble for any freight costs, damages to HALO, or any other costs or liabilities

pertaining to HALO returned without a RAN. Buyer will be responsible

for all freight costs to and from Buyer and repackaging costs, if any, if

Buyer refuses to accept shipment. If the HALO is returned in un-saleable

condition, Buyer shall be responsible for full value of the HALO. Buyer

may not return any special order HALO. Any HALO returned hereunder

shall be subject to a restocking fee equal to 30% of the invoice price.

Limited Warranty. SEI warrants to the original end-user that the

HALO manufactured or provided by SEI under this Agreement shall be

free of defects in material or workmanship for a period of six months or

30,000 kilometers from the date of purchase, provided that the HALO is

installed, used, and maintained in accordance with any user manual or

technical guidelines provided by SEI. The original end-user must give

written notice to SEI of any suspected defect in the HALO prior to the

expiration of the warranty period. The original end-user must also obtain a

RAN from SEI prior to returning the HALO to SEI for warranty service

under this paragraph. SEI will not accept any responsibility for HALO

returned without a RAN. The original end-user shall be responsible for all

costs and expenses associated with returning the HALO to SEI for warranty

service. In the event of a defect, SEI, at its sole option, shall repair or re-

place the defective HALO or refund to the original end-user the purchase

price for such defective HALO. The foregoing warranty is SEI’s sole

obligation, and the original end-user’s exclusive remedy, with regard to any

defective HALO. This limited warranty does not apply to: (a) periodic or

routine maintenance by end-user, (b) defects or damage to the HALO

resulting from improper or unauthorized alterations, modifications, or

changes; and (c) a HALO that has not been installed and/or maintained in

accordance with user manual.

HALO™ is Covered by US Patent No. 7717492, Intl. Pat. Pend.