Hammond Manufacturing DC100 Series User manual

PAGE 1 OF
REV.
BUL86903
B
4
DC100
visit our website:
visitez notre site Web:
ASSEMBLY INSTRUCTIONS
INSTRUCTIONS DE MONTAGE
PRODUCT SERIES
SÉRIE DE PRODUIT
www.hammondmfg.com
FRONT VIEW REAR VIEW
ITEM NUMBER DESCRIPTION DATA CONFIG.
1DC100 RACK FRAME 1
2PERF. DOOR 1
3BARN DOOR (PAIR) 1
4CASTER 4
5VENTED TOP PANEL 1
6VERTICAL CABLE MANAGER 1
7GLAND PLATE 1
8SIDE PANEL (24U ONLY) 1
9MOUNTING RAILS (PAIR) 2
1
23
48
7
6
5
9

PAGE OF
REV.
BUL86903
B
4
ASSEMBLY INSTRUCTIONS
2
INSTRUCTIONS DE MONTAGE
DC100
PRODUCT SERIES
SÉRIE DE PRODUIT
IMPORTANT SAFETY CAUTIONS
NOTE : Read all instructions before installing and using the product.
The following parts are not effectively bonded to the Protective Earth
Terminal (PET): Doors, Rails, Side Panels, Top and Bottom Panels. If
any part needs to be bonded to the PET it shall be done in accordance
with Article 250 of the National Electric Code.
To reduce risk of personal injury and product damage always ensure a
a sufficient amount of personnel are present when loading, unloading,
and moving the enclosure or rack system.
Evenly distribute all mounted loads and equipment to ensure stability
within the system.
Always fully mount and secure enclosure or rack system before loading
equipment.
Ensure unit is plumb and level for proper operation.
Route all chords and cables away from moving parts and all possible
pinch points.
Ensure that the floor/wall structure is able to withstand the weight of
the cabinet while fully loaded.
Installation and assembly must be performed by qualified personnel.
Suitable for mounting on concrete or other noncombustible surface only.
LOADING RACK SYSTEM
NOTE : When loading equipment into the
enclosure or rack system ensure weight is
distributed so that heavier loads are placed
towards the bottom of the rack to avoid
unstable conditions.
Static Load Capacity: 3000lbs
Rolling Load Capacity: 2000lbs or to Max. caster rating

PAGE OF
REV.
BUL86903
B
4
ASSEMBLY INSTRUCTIONS
3
INSTRUCTIONS DE MONTAGE
DC100
PRODUCT SERIES
SÉRIE DE PRODUIT
GROUNDING AND BONDING
INSTRUCTIONS
NOTE : PROTECTIVE EARTH TERMINALS (PET) ARE LABELLED
WITH THE PROPER SYMBOL SHOWN IN FIGURE 1 AND ARE
THE ONLY TERMINALS TO WHICH THE PROTECTIVE EARTH
GROUND CONNECTION SHALL BE ATTACHED TO.
NOTE : ALL PROTECTIVE EARTH AND BONDING CONNECTIONS
SHALL BE IN ACCORDANCE WITH ARTICLE 250 OF THE
NATIONAL ELECTRIC CODE.
1
Included within optional grounding kit (GRDKIT01):
2 x Bonding Wire
10 Gauge
1/4" Ring Terminals
4 x 10-32
Phillips Screw
Pan Head
4 x 10-32
Locking Nut
4 x 1/4"
Flat Washer
4 x 1/4-20
Slotted Screw
Pan Head
4 x 1/4-20
Locking Nut 4 x #10
Flat Washer
4 x 1/4"
Tooth Lock
Washer
4 x #10
Tooth Lock
Washer
6 x 1/4-20
Thread Cutting
Screw
FIGURE 1

PAGE OF
REV.
BUL86903
B
4
ASSEMBLY INSTRUCTIONS
4
INSTRUCTIONS DE MONTAGE
DC100
PRODUCT SERIES
SÉRIE DE PRODUIT
Main Protective Grounding
When grounding the rack system or enclosure it
is essential that the main protective ground is
connected and secured first with its own nut
before any bonding connections are made on
top. (Figure 2)
Bonding Connection
Protective Earth Ground
Figure 2
2
Side Panels: Attach bonding wire found in
ground kit to a bonding stud on the side panel
using the ring terminal and hardware provided.
Attach opposite end of wire to the nearest PET
on the rack frame.
3
Doors: Attach bonding wire to the door stud
using the same method described previously.
Attach the opposite end to the nearest front
section bonding stud.
Bonding Instructions
Top and Bottom Panels: Remove one clip nut
from the frame along with the corresponding
screw. Replace with thread cutting screw,
ensuring it penetrates both the panel and the
frame.
TOP PET
STUDS
(INTERNAL)
BOTTOM PET
STUDS
(INTERNAL)