HAMOKI FM-26 User manual

Hot Display Cabinet
Instruction Manual
Model: FM-26/FM-36/FM-48
1
Please read this instruction manual carefully before
operating this equipment

2
Warning:
Improper installation, adjustment, alteration, service or
maintenance can cause damage, injury or death. Read the
installation, operation and maintenance instructions thoroughly
before installing or servicing this appliance.
Read this instruction manual before
using and keep it available at all
times!
Safety Tips
For your safety:
Do not store gasoline or other flammable liquids in the vicinity of this or
any other appliance.
WARNING: FIRE HAZARD
The area where the appliance is installed must be kept clear of
combustibles and flammables. This includes mops, rags, grease,
wrapping paper and electrical cords.
Warning
Electrical Grounding Instructions
This appliance is equipped with a three-prong (grounding) plug for
your protection against shock hazard and should be plugged directly
into a properly grounded three-prong receptacle. Do not cut or remove
the grounding prong from this plug. If the output exceeds a certain
value, the plug will not be used. Connect the wire to a suitable air
switch.
This appliance is designed for use in non-combustible locations only.
Install the appliance on a firm, level, non-combustible surface.
For servicing, a clearance of 6 inches (15cm) from rear of the appliance
to wall should be kept.

3
About this instruction manual:
This instruction manual contains information about the installation,
operation and maintenance of the appliance and should be used as a
source of information and reference guide. Awareness of the safety
instructions and instructions for use in this manual will ensure the safe and
correct use of the appliance.
In addition to the information given here, you should comply with any local
Health and Safety Controls and generally applicable safety regulations.
The instruction manual forms part of the product and should be kept near
the appliance and easily accessible for anyone carrying out the
installation, servicing, and maintenance or cleaning.
In addition to the information given here, you should comply with any local
Health and Safety Controls and generally applicable safety regulations.
The instruction manual forms part of the product and should be kept near
the appliance and easily accessible for anyone carrying out the
installation, servicing, and maintenance or cleaning.
NOTE! Read the instruction manual carefully before using the appliance.
The user’s manual should be kept near the appliance, easily accessible for
anyone operating the unit. We reserve the right to make technical
changes for purposes of developing and improving the product.
This section provides an overview of all important safety aspects.
Attention should be paid to all symbols, markers and labels on the device,
which must be kept in a prominent location. Following all the important
safety advice will protect against all hazards as well as the operation of
the unit.
This device is designed in accordance with the presently applicable
technological standards. However, the device can pose a danger if
handled or operated improperly and inappropriately.
Knowing the contents of the user’s manual as well as avoiding mistakes
and operating this device safely is essential to protect yourself from the
hazards. To prevent hazards and to ensure optimum efficiency, no
modifications or alterations to the device that are not explicitly approved
by the manufacturer can be undertaken. This device may only be
operated in safe condition following the user’s manual.

4
Safety instructions for the commercial use of the device:
The appliance is intended for commercial use only, and should never be
used for purposes other than stated above. The regional provisions must
be complied with. Besides the industrial safety instructions in the
instruction manual, the general safety and accident prevention
regulations as well as environment protection regulations applicable for
area of application of the device must be followed and complied with.
The device should be never left unattended during operation. Special
attention should be paid to when the unit is in use, if the children are near
the appliance.
This manual is considered to be a permanent part of the appliance. When
passing on/selling the device to a third party, the manual must be handed
over along with the device.
Every person using the unit must act in accordance to the manuals and
under consideration of the safety advice.
Never use the unit outdoors.
Intended use:
CAUTION! Any use other than intended purpose is forbidden and is not
considered as conventional.
Packaging & Storage:
Please do not throw away the packing materials as they might be useful
for storage purposes, when moving or, in case of damage, when the unit
must be sent back. The outer and inner packing material should be
removed completely from the device before installation.
NOTE! Some of the packing materials are re-usable.
Storage:
Do not open the packages until installation. Pay attention to the markings
on the carton surface. Do as the markings indicate. Do not turn the carton
upside down. Care should be taken when moving the appliance. Do not
store outdoors. Keep it dry and dust-free and store in a well-ventilated
area. Do not expose it to direct sunlight. Avoid mechanical shocks and
vibration. In case of longer storage (> 3 months), make sure you check the
state of the packaging regularly.

5
MODEL
FM
-36
FM
-26
FM
-48
POWER INPUT
1.84Kw
1.84kW
2.2kW
RATED
VOLTAGE
220
-240v
220
-240V
220
-240V
FREQUENCY
50/60hZ
50/60hZ
50/60hZ
TEMPERATURE
RANGE
30
-110c
30
-110c
30
-110c
DIMENSIONS
(mm)
900x480x590
660x437x655
1200x480x810
Installation and operation:
Technical data:
The appliance should be connected to a suitable power receptacle.
The outside body should be earthed properly. Never yank or pull the
power cord to disconnect from outlet.
WARNING!
Danger of burning!
During operation, some parts of the appliance may be very hot. Try to
avoid getting burnt and never touch any hot parts without gloves on.
▪Note that the power cord should never touch any heat sources or
sharp edges. Never let thepower cord dangle over the counter edge.
▪Stop using the appliance immediately if malfunctions of the unit
occur. Unplug the appliance.
▪Do not use any accessory or spare parts that have not been
recommended or designated bythe manufacturer. This can pose a
danger for the user or lead to damages of the appliance orpersonal
injury.
▪Do not lay the power cord over carpets or heat insulations. Do not
cover it with any otherobjects. Keep away the power cord from
operating range and do not immerse it into water.
▪Never touch the power cord, plug or the switch when your hands are
wet.
▪Do not leave the unit unattended during operation.
▪Never move or reposition the unit when it is in operation.
▪WARNING! Hazard via electrical current! Make sure that the voltage
of local power supply matches that of the naming plate.

6
ATTENTION!
Place the device on top of a solid, even, safe and stable surface that
tolerates the weight. Level it back and forth. Then leave it side to side.
Do not place the appliance on top of an flammable surface (such as: table
cloth, carpet, etc.).
You must not leave the appliance near open fireplaces, electric ovens,
electric heaters or other heat sources.
Position the device appropriately so that the plug is always accessible.
Make sure liquids don’t get into the electrical system nor the switch. Dry off
the device thoroughly.
When you receive the product, the glass is packed separately inside the
chamber.
Assemble the shelving system and fit the front and rear sliding doors as
indicated below:
Glass sliding Doors:
The unit has front and rear sliding doors. When unpacking, note that the
longer doors fit at the front / sloped section. The doors are fitted by placing
the door into the channel in the top section of the unit first, pushing the
glass far enough up to enable the bottom of the door to clear the bottom
channel and drop down into position in the corresponding bottom
channel. There are two channels which allow the glass doors to slide past
one another. Ensure that the handles are toward the outside of the unit.
Fit the rear doors in the same manner. There are two plastic blocks
supplied, which if placed in the bottom channels in front of the glass will
prevent the doors from opening.
Shelving system:
There are four upright channels which locate into slots provided inside the
unit. The channels have a flat tab at each end, the top side is slightly
longer. Place the channel vertically into the slot provided in the top of the
unit and then drop down to fit through the corresponding slot in the
bottom. Ensure that flat sides are facing inside the unit. The shelf support
angles fit into the slots in the upright channel.
They can be positioned level or slopping forward according to preference.
The wire shelf is positioned on top of the support angle and fits against the
securing tab at the rear of the support angle which prevents the shelf from
sliding forward.
Installation and connection

7
The operation of the device may only be carried out by qualified persons. Before the
first use, clean the inside chamber and the tray grids with a dampened wet cloth
using non-abrasive detergent. After cleaning, dry the unit thoroughly.
Take out the water pan from inside the chamber. Fill water inside the water pan. The
water inside is to produce moisture to keep the inside environment wet. Fill the
water ensuring it does not spill over. Monitor the water level to add the water when
necessary.
Connect the unit to a suitable power supply. Rotate the thermostat clockwise to
your desired value. The yellow indicator will flash on automatically. You may also
turn the illuminators on. The inside temperature of the chamber will be displayed
clearly on the temperature display. When you turn the illuminator on, the red
indicators on the switch will light up. Observe the water level in the pan, add water
when the water inside the pan is lowered to certain positions.
When one day’s work has been finished, shut the main switch off. Unplug the plug.
6.Transportation, Cleaning and maintenance
6.1 Transportation
In the process of transportation, the appliance should be handled carefully,
preventing intense shaking. The packaged appliance should be stored in a well-
ventilated area free of caustic air. It cannot be placed outside and should never be
put upside down. Keep it dry and dust-free. Do not expose it to direct sunlight. Avoid
mechanical shocks and vibrations.
Cleaning/Repair:
Before starting repair or cleaning works, make sure the unit has been disconnected
from power socket (pull off the power plug) and has cooled down completely.
Do not use any acid or abrasive detergents and make sure no water runs into the
internal part of the unit.
To protect yourself from electric shock, never immerse the unit, the power cord and
the plug in water or other liquids.
CAUTION! The appliance is not jet-proofed. Therefore, you must not use any kind of
pressure water jet for cleaning it!
CAUTION!
Do not use any water to clean the control panel. Ensure no water gets inside the
unit. Thoroughly dry off the unit before operating the unit again.
The control panel, surface and power cord should only be wiped off with a piece of
soft cloth dipping a mild cleaning detergent solution. You must not let water enter
the switching unit. This may lead to dangerous currents and malfunction of the
appliance.
Do not use any aggressive cleaning agents or abrasive materials as these could
damage the protecting film of the stainless steel and leave the iron particles on the
surface of the unit, which can cause rust.
All parts must be dried thoroughly and reassemble the parts of unit, which have
been dismantled for cleaning.
Store the device in a dry and ventilated place if the unit stays idle for a long time.
Keep it away from acid steams and caustic gases.
Operation & Safety

8
Safety instructions for maintenance:
▪Check the power cord for damage periodically. Never operate the unit
when the power cord has been damaged or broken. If the power cord
shows the above signs, call a qualified electrician for replacement. It is
highly recommended that the replaced power cord should be the
special type designated by the manufacturer. Damage may be done to
the whole unit and its internal wire if the wrong type of power cord has
been used for replacement.
▪Only a qualified electrician may perform the repair of the unit. All the
necessary replaced parts have to be the types designated by the
manufacturer. Never attempt to repair the unit on your own. Danger
may occur.
Check the appliance before and after use. Before using, make sure the
appliance does not lean. Be certain that the power cord is not worn out or
broken. When in use, make sure no unpleasant smell is present and there is
no any unusual noise.
This manual must be read and understood by all persons using or
installing this appliance. Contact your local dealer if you have any
questions concerning installation, operation or maintenance of this
equipment.
Waste disposal:
Discarding old devices:
At the end of its service life the discarded device has to be disposed in
accordance to the national regulations. It is advisable to contact a
company which specialises in waste disposal, or just contact the local
disposal service in your community.
WARNING!
Make sure the unit is unfit for use before disposal. For that purpose,
disconnect the device from mains supply and remove mains connection
cable from the device.
NOTE!
For the disposal of the device please consider and act according to the
national and local rules and regulations.
Operation & Safety

WARRANTY
9
WARRANTY Hamoki Ltd warrants the original purchaser of every new
product (under normal and proper use and maintenance service as
specified by Hamoki Ltd and upon proper installation and start-up in
accordance with the instruction packet supplied with each unit) a one year
parts warranty.
Hamoki Ltd’s obligation under this warranty is limited to a period of one (1)
year from the date of original installation.
Please note, Bulbs are not included under warranty for this item.
WARRANTY CLAIMS:
All claims for parts must be made directly through the retailer in the first
instance. All claims raised with the retailer should include:
Your name:
Model number:
Your company:
Serial number of the product:
Address: Date of purchase:
Email: Proof of purchase :
Phone:
Information supporting the alleged defect. (A video/photo)
Photo of the dataplate.