HAMOKI VRX1200/330S User manual

1
Manual for Stainless Steel
Refrigerated Display

2

3
Content
Safety Tips·················································4
Introduction·········································· 5
Pack Content·············································· 5
Installation················································· 6
Fit Glass Panels············································· 6
Operation·················································· 7
Storing Food··············································· 7
Turn on··············································· 8
Manual Defrost············································· 8
Cleaning,Care&Maintenance·································· 9
Cleaning the condenser······································· 9
Troubleshooting············································ 10
Technical Specification······································ 11
Electrical Wiring·········································· 11
Disposal·················································· 12
Compliance··············································· 12

4
Safety Tips
·Position on a flat, stable surface.
·A service agent/qualified technician should carry out installation and
any repairs if required. Do not remove any components or service panels
on this product.
·Consult Local and National Standards to comply with the following:
·Health and Safety at Work Legislation
·BS EN Codes of Practice
·Fire Precautions
·IEE Wiring Regulations
·Building Regulations
·DO NOT use jet/pressure washers to clean the appliance.
·DO NOT use the appliance outside.
·DO NOT use this appliance to store medical supplies.
·DO NOT use electrical appliance inside the appliance (e.g, heaters,
ice-cream makers etc.)
·DO NOT stand or support yourself on the base, drawers or doors.
·DO NOT allow oil or fat to come into contact with the plastic
components or door seal. Clean immediately if contact occurs.
·Bottles that contain a high percentage of alcohol must be sealed and
placed vertically in the refrigerator.
·Always carry, store and handle the appliance in a vertical position and

5
move by holding the base of the appliance.
·Always switch off and disconnect the power supply to the unit before
cleaning.
·Keep all packaging away from the children. Dispose of the packaging
in accordance with the regulations of local authorities.
·If the power cord is damaged, it must be replaced by an agent or a
recommended qualified technician in order to avoid a hazard.
Introduction
Please take a few moments to carefully read through this manual. Correct
maintenance and operation of this machine will provide the best possible
performance from your product.
Pack Contents
The following is included:
·Brackets*12 ·Top glass panel*1
·Rear glass panel*1 ·Side glass panel*2
·Knurled screw*12 ·Gastranorm adaptor bar*(amount
according to size)
·Glass clip assembly*6 ·Cross sunk screw*12
·Instruction manual, Thermostat manual*1
·Collar*12 ·Adjustable feet*4

6
We pride itself on quality and service, ensuring that at the time of
packaging the contents are supplied fully functional and free of damage.
Should you find any damage as a result of transit, please contact your
dealer immediately.
Installation
Note: If the unit has been stores or moved in an upright position, let
it stand upright for approximately 12 hours before operation. If in
doubt allow to stand.
1. Remove the appliance from the packaging. Make sure that all
protective plastic film and coatings are thoroughly removed from all
surfaces.
2. Maintain a distance of 20cm (7 inches) between the unit and walls or
other objects for ventilation. Increase this distance if the obstacle is a heat
resource.
Note: Before using the appliance for the first time, clean interior with
soapy water.
3. Level the appliance by adjusting the screw feet.

7
Fit Glass Panels
1. Screw the collars to the rim of the appliance.
Note: Ensure the hole in the collar for the grub screw faces inwards.
2. Slot the two sides panels into the collars, with the holes in the glass at
the top.
3. Insert the collar into the glass hole, equip the bracket inside the glass
panel fixed by the knurled screw.
Note: Ensure that the collar and bracket touch the screw.
4. Slot the rear panel into the collars, with the holes in the glass at the top.
5. Screw the brackets to the inside of each glass collar using the knurled
screws.
6. Insert the glass collar into the top glass panel holes.
7. Place the top panel onto the brackets, ensuring all holes line up.
8. Fix the front panel to the bracket using knurled screws.

8
Operation Storing Food
To get the best results from your appliance, follow these instructions:
1. Only store foodstuffs in the appliance when it has reached the correct
operating temperature.
2. Ensure gastronorm bays are full at all times, even if the gastronorms
are unused or empty.
3. Do not obstruct the fans inside the appliance.
Turn on
1. Close the door(s) of the appliance.
2. Ensure the power switch is set to [O] and turn on at the socket.
3. Switch on the Power [1]. The current temperature within the appliance
is displayed.
Manual Defrost
The appliance will automatically run a defrost cycle every six hours.
Note: The cycle starts from the time the appliance is initially powered
up.
To manually defrost the appliance:
1. Press and hold the DEFROST button for 5 seconds.
2. The defrost cycle will start immediately and the Defrost LED

9
illuminates. The defrost will last a maximum of 30 minutes.
Note: Starting a manual defrost also resets the automatic defrost timer.
The next automatic defrost will start six hours after the manual defrost
has finished.
3. Waste water is collected in the waste water tray.
Cleaning, Care & Maintenance
·Switch off and disconnect from the power supply before cleaning.
·Clean the interior of the appliance as often as possible.
·Do not use abrasive cleaning agents. These can leave harmful residues.
·Clean the door seal with water only.
·Always wipe dry after cleaning.
·Do not allow water used in cleaning to run through the drain hole into
the evaporation pan.
·Take care when cleaning the rear of the appliance. Sharp edges can cut.
An agent or qualified technician must carry out repairs if required.
Cleaning the condenser
Periodically cleaning the condenser can extend the life of the appliance.
We recommend that our agent or qualified technician clean the condenser.

10
Troubleshooting
If your appliance develops a fault, please check the following table before
call your dealer.
Fault
Probable Cause
Action
The appliance is not
working.
The unit is not switched on
Check the unit is plugged in
correctly and switched on
Plug and lead are damaged
Call your agent or qualified
Technician
Fuse in the plug has blown
Replace the fuse
Power supply
Check power supply
Internal wiring fault
Call your agent or qualified
Technician
The appliance turns
on, but the
temperature is too
high/low.
Condenser blocked with dust
Call your agent or qualified
Technician
Appliance is located near a heat
source or air flow to the
condenser is being interrupted.
Move the refrigerator to a
more suitable location
Ambient temperature is too high
Increase ventilation or move
appliance to a cooler position
Unsuitable foodstuffs are being
stored in the appliance
Remove any excessive hot
foodstuffs or blockages to the
fan
Appliance is overloaded
Reduce the amount of food
stored in the appliance
The appliance is
unusually loud
Loose nut/screw
Check and tighten all nuts and
screws
The appliance has not been
installed in a level or stable
position
Check installation position and
change if necessary

11
Technical Specifications
Electrical Wiring
Appliances are supplied with a 3 pin, plug and lead, with a 10 amp as

12
standard. The plug is to be connected to a suitable mains socket.
Appliance are wired as follows:
·Live wire ( colored brown ) to terminal marked L
·Neutral wire ( colored blue ) to terminal marked N
·Earth wire ( colored green/yellow ) to terminal marked E
All appliances must be earthed, using a dedicated earthing circuit.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In event
of any emergency disconnection being required they must be readily
accessible.
Disposal
EU regulations require refrigeration product to be disposed of by
specialist companies who remove or recycle all gasses, metal and plastic
components.
Consult your local waste collection authority regarding disposal of your
appliance. Local authorities are not obliged to dispose of commercial
refrigeration equipment but may be able to offer advice on how to dispose
of the equipment locally.
Compliance
Parts have undergone strict product testing in order to comply with
regulatory standards and specifications set by international, independent,

13
and federal authorities.
Products have been approved to carry the following symbol:
Hamoki Limited
www.hamoki.co.uk