Hang ups Teeter Power V User manual

Note: The Bed Frame arrives rotated into the fully inverted position. This is the
most convenient position from which to begin the assembly process.
STEP ONE
Attach the Bed Frame (P1-6000) to the A-Frame (P1-1005)
• Open theA-frame and make sure that the spreader arms are locked flat.
• Lift the Bed Frame (the bed mat will be facing the rear) and place the
shrouds over the top of theA-Frame legs (SeeFigure1).
WARNING: The Bed Frame weighs 50 lbs. If you are unsure of
your ability to comfortably lift this weight, please seek assistance
with assembling this product.
• Make sure the Bed Frame rests evenly on theA-Frame and that the
holesarealigned.
• Insert and tighten the Screws (H1-1603) into the shrouds on both sides
of theBedFrameusingthe Wrenchprovided (SeeFigure2).
Shroud
DONOTDISCARD- KEEPFOR FUTURE REFERENCE.
Figure 1
Figure 2
ASSEMBLY
Patent applies.
ASSEMBLYINSTRUCTIONS
Power VTM
Before you begin: These instructions will guide you in properly assembling the unit. Please review all the steps before beginning assembly.
Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure user security and product integrity.
Main Shaft
P1-6002
Wrench
P1-6005
P1-1003
arriveassembled
inthemainshaft
Locking Knobs
BedFrame
P1-6000
ITEMSFORASSEMBLY ITEM #’s
Bed Frame P1-6000
A-Frame P1-1005
A-Frame Locking Knob P1-1004
Main Shaft P1-6002
Locking Knobs (2) P1-1003
Screws (4) H1-1603
Wrench P1-6005
Handles (2) P1-2003
Carefully remove the individual parts from the carton. You should have all of the items listed below. If any items are missing or damaged, contact
your retailer or customer service directly (See reverse side).
PRE-ASSEMBLY
1. It is your responsibility to familiarize yourself with the proper use of the equipment and the inherent risks of inversion, such as falling on your
head or neck, pinching, entrapment or equipment failure.
2. This product is not designed for persons over 6ft 6in (198 cm) or 300 lbs (136 kg). Structural failure could occur or head/neck may impact floor
during inversion. Serious injury or death could result.
3. DO NOT use the equipment without a licensed physician’s approval and a review of the medical contraindications, as noted in the Owner’s Manual.
4. Failure to assemble and/or use the equipment as directed may void the manufacturer’s warranty on this product and could result in injury or death.
5. DO NOT use the inversion table until you have thoroughly and carefully read the Owner’s Manual, reviewed all other accompanying
documents, and inspected the equipment.
6. This product requires a grounded outlet. Improper connection to a 3-prong grounded outlet can result in electrical shock.
7. Choose a level surface for assembling and operating the table.
8. Follow each step in sequence. Do not skip ahead.
9. Make sure that all fasteners are secure.
10. PRIOR TO USE, test and inspect the table. Make sure that the table rotates smoothly to the inverted position and back.
11. Replace defective components immediately and/or keep the equipment out of use until repair.
12. Refer to additional warning notices and information posted on the equipment.
WARNING
!
Handles
P1-2003
Screws
H1-1603
ASSEMBLY
Ensure the Bed Frame is securely attached to the A-frame and
that the A-frame sits evenly on the floor. Improper assembly
could cause serious injury or death.
!WARNING
rear front
A-Frame
P1-1005
A-Frame
Locking Knob
P1-1004

ASSEMBLY
STEP FIVE
Connect cord to the power source
• Attach the power cord on the Bed Frame to the receptor at the end of the Main
Shaft(SeeFigure6).
• Connectthepower source cord toan outlet. RotatetheBed upright(See Figure 7)
usingtheRotationControl Button (thebuttontowardtherearof the table).
• Push theAnkle ClampAdjustment Button to ensure the Front Clamps operate
smoothly. If there is a failure of one or both buttons, or the parts do not operate
smoothly, there is a malfunction and you should contact
customerservice.
GROUNDINGINSTRUCTIONS
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance
for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-
grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly
grounded. Do not modify the plug provided with the product - if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
Assembly Instructions LP-1035 Pg. 2
USA & Canada:
STL International, Inc.
9902 162nd St. Ct. E.
Puyallup, WA 98375
(Phone) 800-847-0143
(Fax) 800-847-0188
(email) [email protected]
(web) www.STLIntl.com
Patentapplies.
TeeterHangUps®isaregisteredtrademarkofSTL
International,Inc.andInversionInternational,Ltd.
Specificationssubjecttochangewithoutnotice.
©COPYRIGHT2006,STLInternational,Inc.and
InversionInternational,Ltd.
InternationalLawProhibitsAnyCopying,10/06-2
International:
Inversion International, Ltd.
PO Box: AP 59245
New Providence Island, Bahamas
(Phone) [phone]
(Fax) [phone]
(email) [email protected]
(web) www.InversionInternational.com
STEP FOUR
Secure the Main Shaft (P1-6002) to the Bed Frame (P1-6000)
• Insert the Main Shaft into the Bed Frame (See Figure 5).
• Line up the holes on the back of the bed with those on the Main Shaft. Insert and
hand-tightenboth Locking Knobs (P1-1003) tosecuretheMain Shaft to the BedFrame.
STEP THREE
Attach the Handles (P1-2003)
• Removethepre-assembledshippingscrewsintheHandlearmsanddiscard.
• Insert and screw in the Handles into the arms of both sides of the Bed Frame
(SeeFigure4).
Figure 6
Figure 4
Figure 7
Figure 5
STEP FIVE
You have completed assembly of the Power VTM Inversion Table.
• ReadyourOwner’sManualthoroughlybeforeusing the inversion table.
• For your reference, the table’s serial number can be found on a sticker mounted to
themotorhousing.
Failure to secure the Locking Knobs could cause your head to impact
the floor, resulting in serious injury or death.
WARNING
!
Europe:
Teeter Ltd.
Cygnet House, Sydenham Road
Croydon, Surrey CR0 2EE, UK
(Phone) [phone]
(Fax) [phone]
(email) [e-mail]
(web) www.TeeterLtd.com
For information about the Teeter Hang Ups®2-year warranty, to order replacement labels or manuals, or
if you have any problems assembling the equipment or questions about its use, please contact Customer
Service at the appropriate location below:
STEP TWO
Secure the A-Frame Locking Knob (P1-1004)
• Hand-tightentheA-FrameLockingKnobintotheA-Frame Locking Knob housing
locatedon the side oftheA-Frame opposite of theRotationControland Foot Clamp
Buttons.(SeeFigure3)
Figure 3