Hang ups Teeter Fit-50 User manual

FIT™Series
R
Inversion Table Assembly Instructions*
for Fit-50 & Fit-60 models
T
E
E
T
E
R
H
A
N
G
U
P
S
2
YEAR
W
A
R
R
A
N
T
Y
*Inversion Table images may vary slightly
from your model; however, all assembly
instructions remain the same.

IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE.
SAVE THESE INSTRUCTIONS
WARNING
!
WARNING - To reduce the risk of injury to persons:
• Read and understand all the instructions, review all other accompanying documents, and inspect the equipment before using the inversion table. It is your
responsibility to familiarize yourself with the proper use of this equipment and the inherent risks of inversion, such as falling on your head or neck, pinching,
entrapment, or equipment failure. It is the responsibility of the owner to ensure that all users of the product are fully informed about the proper use of the
equipment and all safety precautions.
•
Close supervision is necessary when the inversion table is used near children, or by or near invalids or disabled persons.
• Use the inversion table only for its intended use as described in this manual. DO NOT use attachments not recommended by the manufacturer.
• NEVER drop or insert any object into any opening.
• DO NOT use or store product outdoors.
• DO NOT use if you are over 6 ft 6 in (198 cm) or over 250 lbs. (113 kg). Structural failure could occur or head/neck may impact the oor during inversion.
• DO NOT allow children to use this machine.
• Keep children, bystanders, and pets away from machine while in use.
• Keep body parts, hair, loose clothing and jewelry clear of all moving parts.
• The inversion table has no user serviceable parts.
• This product is intended for indoor home use only. DO NOT use in any commercial, rental or institutional setting.
• DO NOT use the equipment without a licensed physician’s approval and a review of the medical contraindications, as noted in the Owner’s Manual.
• Failure to assemble and/or use the equipment as directed may void the manufacturer’s warranty on this product and could result in injury or death.
• Choose a level surface for assembling and operating the inversion table.
• Follow each step in sequence. DO NOT skip ahead.
• Make sure that all fasteners are secure.
• ALWAYS test and inspect the inversion table. Make sure the table rotates smoothly to inverted position and back.
• ALWAYS replace defective components immediately and/or keep the equipment out of use until repair.
FAILURE TO FOLLOW INSTRUCTIONS AND WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.
BEFORE YOU BEGIN: Review all steps before beginning assembly and read all precautions before using the inversion table.
Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure safety and product integrity.

F1-1500
FF-1148*
*May come pre-assembled
in Handles
F1-1550
F5-1064 F1-1250
F5-1088
Items are not shown to scale. If you have any questions on assembly, contact Customer Service at 1-800-847-0143 or visit our website at teeter-inversion.com.
Items for Assembly
ITEMS FOR ASSEMBLY ITEM NUMBER
F1-1600
F1-1100
F5-1007
F1-1350
IA-1149
IA-1119
IA-1118
F5-1130IA-1123
H1-1202*
*May come pre-assembled
in Hinge Covers
EP-1045B F5-1051 F5-1048
H1-3010
H1-1212
A-Frame
Angle Tether
Table Bed Assembly
Fit-50 Table Bed
Fit-60 Table Bed
Main Shaft
with T-Pin Ankle Lock System
F1-1100
F5-1007
F1-1350
F1-1360
F1-1600
ITEMS FOR ASSEMBLY ITEM NUMBER
Rear Ankle Bar
Heel Cups (2)
One pre-assembled, one separate
Bolt/Nut
Rubber Plugs (2)
One pre-assembled, one separate
Front Ankle Bar
Foam Rollers (2)
Bolt
Nut
End Cap
Ankle Comfort Dial Bar
Ankle Comfort Dials (2)
One pre-assembled, one separate
Screw
IA-1113
F5-1054
F5-1087
F5-1056
EP-1045B
F5-1051
H1-1212
H1-3010
F5-1048
IA-1119
IA-1118
IA-1123
ITEMS FOR ASSEMBLY ITEM NUMBER
Handles
Fit-50 Handles* (2)
Fit-60 Support Handles* (2)
Chicago Bolts & Nuts (2)
Bolts & Nuts may come
pre-assembled in Handles
3-Hole Roller Hinges (2)
Hinge Covers (2)
Hex Bolts (4)
Bolts may come pre-assembled
in Hinge Covers
Tools
10/13mm Wrench
5mm Allen Wrench
Screwdriver
F1-1550
F1-1500
FF-1148
F5-1064
F1-1250
H1-1202
F5-1088
IA-1149
F5-1130
IA-1113
F5-1054
F5-1087
F5-1056*
*1 will be pre-assembled
in Rear Ankle Bar
F1-1360

A
B
C
D
E
F
G
H
I
J
K
L
M
Table Bed
Handles
3-Hole Roller Hinges
Hinge Covers
Height-Selector Locking Pin
Spreader Arms
Main Shaft
Angle Tether
Crossbar
T-Pin Ankle Lock System
A-Frame
Ankle Comfort Dial™
Stability Feet
A
H
L
I
D
F
G
B
K
M
Before Beginning
Before reading further, study the drawing below to familiarize yourself with the important
components of your new Teeter Hang Ups® Inversion Table.
C
E
J
*Inversion Table images may vary slightly
from your model; however, all assembly
instructions remain the same.

Step 1
Open the A-Frame (F1-1100)
• Open the A-Frame on the floor and make sure the Spreader Arms are locked open (Figure 1).
• Familiarize yourself with the Front, Back, Left and Right of the A-Frame. You may want to refer back to this diagram
for reference throughout the assembly process.
Depending on the model you have purchased, the item numbers in this step will vary.
The model of your product can be found on the Serial Label, located on the back of the Table Bed.
Install the 3-Hole Roller Hinges (F5-1064) onto the Table Bed
• For ease-of-assembly, rest the Table Bed against the crossbar of the A-Frame (Figure 2).
• Open the Cam Locks on each side of the Table Bed (Figure 3).
• With the Pivot Pins facing outward, insert the Roller Hinges into the brackets on each side of the Table Bed.
The Roller Hinges must slide between the Cam Locks and the Brackets (Figure 3).
• Engage one of the holes in the Roller Hinge over the Bracket Pin. Make sure the Roller Hinges are in the same hole
setting on both sides. Figure 4 shows the Roller Hinges engaged correctly in Setting C.
• Push down on the Cam Locks (Figure 5) to secure the Roller Hinges.
Bracket Pin
2Cam Lock
3
Pivot Pin
1
C
B
A
123
Figure 3
Figure 4
Figure 5
Unlocked Locked
Back
Spreader Arms
1Crossbar
2
Front
2
1
Right Left
Figure 1
Figure 2 Step 2

Step 3
Depending on the model you have purchased, the item numbers in this step will vary.
The model of your product can be found on the Serial Label, located on the back of the Table Bed.
Attach the Table Bed to the A-Frame (F1-1100)
• Pick up the Table Bed, holding each side near the Roller Hinges, and stand in front of the A-Frame where the Crossbar
is located (refer to Figure 1 to determine A-Frame Front).
• Lower each Roller Hinge Pivot Pin into the A-Frame hinge plates, one side at a time (Figure 6 and 6A).
NOTE: You may need to push outward on the A-Frame in order for the 2nd Pivot Pin to lock in place.
• Make sure that each Pivot Pin is seated at the base of the slot of the Hinge Plate (Figure 7).
• Ensure that the Self-Locking Hooks have closed over both Pivot Pins, and that the Table Bed rotates smoothly.
WARNING
!
Failure of the Self-Locking Hooks to close over both Roller Hinge Pivot Pins is an indication
of improper assembly and if not corrected could result in serious injury or death!
2Self-Locking Hook
Roller Hinge Pivot Pin
1
1
2
Self-Locking Hook
1Roller Hinge
2
1
2
Figure 7
Figure 6A
Figure 6

Assemble the T-Pin Ankle Lock System onto the Main Shaft (F1-1600)
Install the Ankle Comfort Dial
• Slide the Ankle Comfort Dial Bar (IA-1119) with pre-assembled Ankle Comfort Dial into the hole at the front base
of the Main Shaft (Figure 8).
• The Ankle Comfort Dial is designed with a High and Low setting. Position the pre-assembled Dial in the Low Setting
(screw holes facing up) for ease of assembly. Slide the separate Ankle Comfort Dial (IA-1118) onto the Ankle Comfort
Dial Bar.
• Insert the Screw (IA-1123) (Figure 9) and tighten with the Screwdriver (F5-1130) provided.
NOTE: Refer to the Owner’s Manual for a complete description of the Ankle Comfort Dial settings.
Install the Rear Ankle Bar
• With the rounded corners of the pre-assembled Heel Cup facing down, insert the Rear Ankle Bar (IA-1113) into the
large hole at the back of the Main Shaft (Figure 10).
• Insert the Bolt (F5-1087) from the rear of the Main Shaft to secure the Rear Ankle Bar (Figure 10), and tighten the
Washer and Nut with the wrenches provided.
• Slide the separate Heel Cup (F5-1054), with the rounded corners down, onto the open end of the Rear Ankle Bar
(Figure 11).
TIP: To assist with assembly, repeatedly rotate the Heel Cup while pushing it onto the Rear Ankle Bar.
• Insert the Rubber Plug (F5-1056) into the end of the Rear Ankle Bar (Figure 12).
TIP: You may want to use a rubber mallet to assist with assembly.
Figure 8
Figure 10
Figure 12
Figure 9
Figure 11
Step 4

Step 4
Install the Front Ankle Bar
• Insert the Front Ankle Bar (EP-1045B) into the Front Ankle Bar Housing (Figure 13). Pull up on the T-Pin Lock to insert
the Front Ankle Bar all the way and release in the shortest setting (the hole closest to the Front Ankle Bar).
• From the reverse side, pull on the zip-tie to stretch the Retainer Spring and Cable Loop so that they align with the hole
at the back of the Front Ankle Bar Housing (Figure 14).
• Insert the Bolt (H1-1212) through the hole, both loops and the hole on the other side of the housing (Figure 14A).
• Tighten the Nut using the 10/13mm Wrench (F5-1088) provided.
• Cut the long portion of the zip-tie with scissors (Figure 14A) and cover the open end with the End Cap (F5-1048)
(Figure 14B).
Install the Foam Rollers
• Slide the Foam Rollers (F5-1051) onto the Front Ankle Bar (Figure 15).
TIP: To assist with assembly, repeatedly rotate the Foam Roller while pushing it onto the Front Ankle Bar.
WARNING
!
Do not apply lubricants to any part of the inversion table.
Failure to assemble the T-Pin Ankle Lock System properly could result in serious injury or death!
Figure 13
Figure 14
Figure 14A
Figure 15
Retainer Spring &
Cable Loop
1
1
1
Front Ankle Bar Housing
1
Figure 14B
(continued)

Step 5
Insert the Main Shaft (F1-1600) into the Table Bed
• With the Height Adjustment Settings on the Main Shaft facing up, slide the end of the Main Shaft into
the Main Shaft Housing (Figure 16) on the Table Bed.
• Pull out the Height-Selector Locking Pin to allow the Main Shaft to slide in further and release in the desired
height setting. Refer to the Owner’s Manual for more information on selecting your height setting.
• The Main Shaft MUST REST against the Crossbar of the A-Frame (Figure 17).
NOTE: The Crossbar prevents the Table Bed from rotating forward when the user steps on the Ankle Comfort Dial.
If the Main Shaft does not rest on the Crossbar as shown in Figure 17, then the Table Bed has been assembled
backwards onto the A-Frame. This MUST BE CORRECTED before use.
Main Shaft
Main Shaft Housing
Height-Selector Locking Pin
2
3
1
Crossbar
1Proper Resting Position
2
FRONT
Figure 16
Figure 17
123
1
2

Step 6
Depending on the model you have purchased, the item numbers in this step will vary.
The model of your product can be found on the Serial Label, located on the back of the Table Bed.
Assemble the Handles for your model onto the A-Frame (F1-1100)
Bolts/Nuts may come pre-assembled in the Handles. Simply unscrew to remove.
Fit-50 will use: Handles (F1-1550)
Fit-60 will use: Support Handles (F1-1500)
• Insert the Handles into the A-Frame (Figure 18).
• From the rear of the A-Frame, insert the Chicago Nut (FF-1148) through the corresponding 1/4” hole, located on the
Handle Housing (Figure 19).
• From the front of the A-Frame, insert the Chicago Bolt (FF-1148) (Figure 19) and tighten using the wrenches provided.
Attach the Hinge Covers (F1-1250) to the Hinge Plates.
Hex Bolts may come pre-assembled in Hinge Covers. Simply unscrew to remove.
• Select the corresponding Hinge Cover for the left or right side of the A-Frame by aligning each with the shape
of the Hinge Plate (Figure 20).
• Secure with two (2) Hex Bolts (H1-1202) for each side using the 10/13mm Wrench (F5-1088) provided.
Be careful not to overtighten.
Step 7
Chicago Nut
1
Hinge Cover
1
1
Figure 18
Figure 19
Figure 20
1
2
Chicago Bolt
2
Hex Bolts
2
2

Step 8
Attach the Angle Tether (F5-1007) to Limit the Degree of Rotation
• The Angle Tether will come pre-assembled to the A-Frame.
• Unfold the adjustable Angle Tether and clip it to the U-Bar on the underside of the Table Bed (Figure 21).
Before Use
• Test the Inversion Table by hand for smooth and steady rotation (Figure 22).
• Ensure that all fasteners are secure.
• Please complete the warranty registration online at www.teeter-inversion.com.
• For your reference, the serial number can be found on the back of the Table Bed.
WARNING
!
Read the Owner’s Manual thoroughly before using your Teeter Hang Ups Inversion Table.
Improper settings could result in serious injury or death!
Figure 22
Figure 21

WARNING
!
If your Teeter Hang Ups Inversion Table looks like either of these images, your table has been misassembled and is unt for use.
Image A demonstrates that the Roller Hinges have been assembled upside down into the Table Bed and must be corrected. Go back to Step 5 for instruction.
Image B demonstrates that the Table Bed has been assembled into the A-Frame backwards and must be corrected. Go back to Step 6 for instruction.
Improper assembly could result in serious injury or death!
Image A Image B

C
B
A
Adjustments / Maintenance / Storage
Adjustments: Changing the Roller Hinge Setting
To adjust the Roller Hinge setting, you’ll need to fully remove the Table Bed from the A-Frame.
• Pull the Height-Selector Locking Pin and slide the Main Shaft in all the way.
• Release and engage the Pin in the storage setting (the last hole).
• Rotate the Table Bed opposite from use until it has turned 180 degrees and rests against the
Crossbar of the A-Frame (Figure 23).
• With palms up, reach under and around each Roller Hinge, using your thumbs to release the locks over the
Pivot Pin (Figure 23A).
• Lift both sides of the Table Bed out of the A-Frame at the same time.
TIP: Rest the head of the Table Bed on the floor for quick adjustment.
• Unlock the Cam Locks for each Roller Hinge. Change the Roller Hinges to the desired setting of A, B or C (Figure 24).
NOTE: Refer to the Owner’s Manual for more information on finding your Roller Hinge Setting.
• Re-lock the Cam Locks. Replace the Roller Hinges into the hinge plates of the A-Frame.
• Rotate the Table Bed back to the use position and re-adjust the Main Shaft height settings for use.
Maintenance
• To clean the Inversion Table, wipe down with a damp cloth. Do not use abrasive cleaners or solvents.
Storage
• Pull the Height-Selector Locking Pin and slide the Main Shaft in all the way.
• Release and engage the Pin in the storage setting (the last hole).
• Rotate the Table Bed opposite from use until it has turned 180 degrees and rests against the Crossbar of the A-Frame.
• Pull up on the Spreader Arms to fold the A-Frame (Figure 25, leaving the A-Frame legs open to a width of at least
12” for stability.
NOTE: This operation may pinch fingers if not done slowly and carefully.
WARNING
Tipping Hazard: For upright storage, leave A-frame open wide enough to remain stable, or secure to the wall
to prevent tipping. In households with small children, the inversion table should be stored at on the oor, not upright.
!
Figure 23A
Figure 25
Figure 24
Figure 23

U.S. and Foreign Patents Pending. Teeter Hang Ups is a registered trademark of Teeter.
Specications subject to change without notice.
© COPYRIGHT 2011 Teeter. International Law Prohibits Any Copying
F1-1756 0811-0
Any modication to
this device will void
the UL Listing.
MDSS GmbH
Schiffgraben 41
30175 Hannover, Germany
EC REP
If you have any problems assembling the equipment, or questions about its use, please contact customer service at:
USA: Teeter
Toll Free (Phone) 800-847-0143
(Fax) 800-847-0188
[email protected]
www.teeter-inversion.com
International: Inversion International, Ltd.
(Phone) [phone]
(Fax) [phone]
[email protected]
www.InversionInternational.com