Hanna instruments Bl 983320-0 User manual

WARRANTY

Instruction Manual

BL 983320-0

BL 983320-1

Panel-Mounted

EC Indicators &

Controllers

GENERAL DESCRIPTION

SPECIFICATIONS

Range 0.0 to 199.9 µS/cm

Resolution 0.1 µS/cm

Accuracy (@ 20°C/68°F) ±2% f.s.

Typical EMC Deviation ±2% f.s.

Probe HI 7634-00 EC/TDS probe (not included)

Temp.Compensation Automatic from 5 to 50°C (41 to 122°F);

ß=2%/ºC

Calibration Manual, through CAL trimmer

Dosing Contact Maximum 2A (fuse protected), 250 Vac, 30 Vdc

Contact close when measure > setpoint

Setpoint Adjustable, from 0 to 199.9 µS/cm

Overtime Adjustable, typically from 5 to approx. 30 minutes

Power Consumption 10 VA

Installation Category II

Power supply: External (fuse protected)

BL983320-0 12 Vdc

BL983320-1 115/230 Vac ; 50/60Hz

Dimensions 83 x 53 x 99 mm (3.3x2.1x3.9”)

ACCESSORIES

Recommendations for Users

Before using these products, make sure that they are entirely suitable for the environment

in which they are used. Operation of these instruments in residential areas could cause

unacceptable interferences to radio and TV equipment. Any variation introduced by the user

to the supplied equipment may degrade the instrument’s EMC performance. To avoid

electrical shock, do not use these instruments when voltages at the measurement surface

exceed 24 Vac or 60 Vdc. To avoid damages or burns, do not perform any measurement in

microwave ovens.

Remove the instrument from the packing material and

examine it carefully. If any damage has occurred during

shipment, immediately notify your Dealer or the nearest

Hanna Customer Service Center.

Each meter is supplied with:

• Mounting brackets

• Instruction manual

Note: Conserve all packing material until the instrument

has been observed to function correctly. Any defective

item must be returned in its original packing.

Dear Customer,

Thank you for choosing a Hanna product.

This manual will provide you with the necessary information

for the correct operation of the meter. Please read it carefully

before using the instrument.

If you need additional technical information, do not hesitate

to e-mail us at [email protected].

These instruments are in compliance with the directives.

PRELIMINARY EXAMINATION

BL983320-0 and BL983320-1 are conductivity indicators

and controllers with a relay output designed for simplicity of

use in a wide range of applications.

Connections and wiring to probe, power supply and contacts

are made via the terminal blocks on the rear panel.

The probe is easy to clean and requires little maintenance.

Other features include: automatic temperature compensation

of readings, single point calibration, overtime control system,

multi-colour LED for indicating if the meter is in measure-

ment/dosing/alarm condition, possibility to set (Off-Auto-On

switch) dosing action mode.

Two models are available:

• BL 983320-0 powered at 12 Vdc

• BL 983320-1 powered at 115 or 230 Vac

HI 7634-00 EC/TDS probe

HI 70033P 84 µS/cm calibration solution, 20 mL

sachet (25 pcs)

HI 7033M 84 µS/cm calibration solution, 230 mL

HI 7033L 84 µS/cm calibration solution, 500 mL

HI 7061M Probe cleaning solution, 230 mL bottle

HI 7061L Probe cleaning solution, 500 mL bottle

HI 710005 12 Vdc power adapter, US plug

HI 710006 12 Vdc power adapter, European plug

HI 710012 12 Vdc power adapter, Australian plug

HI 710013 12 Vdc power adapter, South African plug

HI 710014 12 Vdc power adapter, UK plug

HI 731326 Calibration screwdriver (20 pcs)

HI 740146 Mounting brackets

CE DECLARATION OF CONFORMITY

ASSEMBLING VIEW

These instruments are warranted for two years against defects in work-

manship and materials when used for their intended purpose and

maintained according to instructions. Probes are warranted for six months.

This warranty is limited to repair or replacement free of charge.

Damages due to accident, misuse, tampering or lack of prescribed main-

tenance are not covered. If service is required, contact the dealer from

whom you purchased the instrument. If under warranty, report the model

number, date of purchase, serial number and the nature of the failure. If

the repair is not covered by the warranty, you will be notified of the

charges incurred. If the instrument is to be returned to Hanna Instruments,

first obtain a Returned Goods Authorization Number from the Customer

Service department and then send it with shipment costs prepaid. When

shipping any instrument, make sure it is properly packaged for complete

protection.