Hanover ADL17002 User manual


HanoverOutdoorFurniture




IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com


Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)

Page 4
ASSEMBLY INSTRUCTIONS
1
2
From behind the chaise lounge back frame, insert a bolt with Ø8.5x1.5 mm washer through the hole in the lower
sling back frame. Add a Ø15x4 mm plastic washer before inserting into the fixed nut in side the sling seat frame
(see diagram). . Completely tightening at this point could cause the frame or
the sling seat to be uneven. Repeat for the opposite side.
Hand tighten 3-4 revolutions only
Using the hex wrench provided, tighten bolts. Tighten each bolt a few revolutions at time, alternating back
and forth between the two bolts until they are completely tightened. It is important to alternate between bolts
to ensure your frame and sling seat are even. . Over tightening could damage the threads
on the bolts or nuts.
Do not over tighten
D
E
C
A
B
FOOT CAP

Page 5
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
5/16" X 42 MM BOLT HW0809 2
2
Ø15X4MMPLASTIC
WASHER HW0026
ADJUSTMENT BAR
FACTORY ASSEMBLY
BUMPER
FACTORY ASSEMBLY HW0078
SLING SEAT FRAME
1
1
SLING BACK FRAME
PARTS LIST DESCRIPTION ORDER PART # QTY
A
B
C
D
E
F
2
Ø8.5 X 1.5 MM
WASHER HW0005
SLING TUBE CAP-2
FACTORY ASSEMBLY FC0468
HEX BOLT DRIVER 1
HW0006
FC0030
FOOT CAP
FACTORY ASSEMBLY
SLING TUBE CAP 1-
FACTORY ASSEMBLY FC0005
ADL17002
AL1584
AL1585
AL1586

Page 4
ASSEMBLY INSTRUCTIONS
1
2
.Attach a side panel to the legs by using the bolts and washers as shown in .
side panel legs
Fig 1
Hand tighten only.
Guide the bolts through the
holes in the into the pre-drilled holes in the . Repeat for the other side
panel.
Attach the umbrella base pole to the bottom panel by using the bolts Guide
these bolts through the holes in the , into the pre-drilled holes in the umbrella . Do
not over tighten
and washers as shown in .
bottom panel base pole
Fig 2.
.
F
F
H
G
G
CB
D
E
FOOT CAP
H

Page 5
ASSEMBLY INSTRUCTIONS
3
4
Place the table top upside down on a flat, non-abrasive surface. Attach the table legs to the table top by using the
..
bolts and Guide these bolts through the holes in the legs, into the pre-drilled holes in
the table top Use the hex bolt driver to tighten all bolts . Over tightening may strip bolts.
Cover all bolts with covers
Do not over tighten
washers as shown in .Fig 3.
.
After adjusting any necessary alignment of legs side panels, and bottom panel, use the hex bolt driver to tighten
all bolts. each bolt must be tightened a few revolutions at a time. In order to apply equal pressure to all
bolt joints, we recommend working in a cross corner (X fashion). Repeat until all bolts are tight.
. Over tightening may strip bolts. Cover all bolts with covers.
Note:
Do not over
tighten
,
Attach the bottom panel with umbrella base pole to the table leg(B) & side panel(C) by using the bolts and
washers as shown in . Guide these bolts and washers through the holes in bottom panel, into the
pre-drilled holes in the table leg (B) & side panel (C).
Fig.4
Hand tighten only.
5
A
F
G
F
G
H
H

Page 6
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
APS06515
PARTS LIST DESCRIPTION ORDER PART # QTY
A
B
C
D
E
F
G
H
I
TABLE LEG
SIDE PANEL
BOTTOM PANEL
TABLE TOP
2
2
1
1
1
HW0034
1/4" X 15 MM BOLT 19
UMBRELLA
BASE POLE
BOLT COVER HW0105
HEX BOLT DRIVER HW0006
Ø6.5 X 1.0 MM
WASHER HW0004
1
19
19
FOOT CAP
FACTORY ASSEMBLY FC0492
UMBRELLA POLE
LOCK KNOB
FACTORY ASSEMBLY
FC0725
AT70658
AT70659
AT70660
AT70661
AT70662