PREMIER POLYSTEEL Champion 922-101 User manual

96 1/2"
4"
33" 30"
20"
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 642-111 Champion Square Table Top 1
2 634-121 Sq./Rnd Table Free Standing Leg W/Back 8
3 634-119 Sq./Rnd Table Leg Support Bracket 1
4 622-019 40" Champion Seat 8
5 516-058 3/8"x1-1/2" SS Hex Bolt 48
6 516-023 3/8" SS Flat Washer 96
7 516-028 3/8" SS Nylock Nut 48
X.01
922-101
Premier 4' Champion Square With Back Rests Expanded Metal Free
Standing Picnic Table
SHEET 1 OF 2 REV.
A
SIZE

A
4
2
1
3
DETAIL A
SCALE 1 : 8
5
6
7
6
Place the tabletop upside down on top of a pair of sawhorses or 12” blocks (cover the blocks with 1.
cardboard) and drill out the 8 holes in the frame using a 7/16” drill bit.
Drill out the 8 holes in the leg bracket with the same 7/16” drill bit. 2.
Drill out the 6 holes on each of the table legs using the 7/16” drill bit. 3.
Attach the leg top to the inside of the tabletop frame with a hex bolt, 2 washers and a nylock nut. Do 4.
not tighten completely.
Repeat step 4 by attaching another leg on the same side as the first. 5.
Attach the leg bracket to the threaded stud on the 2 legs that you just attached to the tabletop. Use a 6.
washer and nylock nut. Again do not tighten completely.
Continue attaching the legs to the tabletop and leg bracket. When you have all of the legs attached, flip 7.
the table right side up.
Drill out the 4 holes in the seat/back and install them onto the legs. Note: The cross frames on the 8.
seat/back aren’t the same distance from the ends. Be sure to align the seat with the back. The cross
frame on the seat/back attaches to the same side of the mounting plate on each leg. (Both on the left or
both on the right)
When you have all of the parts attached you can begin tightening the bolts. Make sure the table is on a 9.
level surface and adjust the legs and set/backs so that they are level as you tighten each component.
X.01
922-101
Premier 4' Champion Square With Back Rests Expanded Metal Free
Standing Picnic Table
SHEET 2 OF 2 REV.
A
SIZE
In Accordance to California law: WARNING This product contains a
chemical known to the State of California to cause cancer and
birth defects or other reproductive harm.

76"
76"
40"
30"
20"
1. With table top upside down bolt 2 opposing legs on to top. Do not tighten the bolts now.
2. Attach “x” shaped leg brace to the 2 legs.
3. Attach the other 6 legs fastening to the “x” shaped leg brace as you go.
4. Attach seats to other end of leg. The vertical portion of the angle iron leg top bolts flush with
the seat support bar.
5. Flip the table right side up, level the top and seats, and tighten all of the bolts.
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 642-111 Champion Square Table Top 1
2 634-111 Sq./Rnd Table Free Standing Leg 8
3 634-119 Sq./Rnd Table Leg Support Bracket 1
4 622-019 40" Champion Seat 4
5 516-058 3/8"x1-1/2" SS Hex Bolt 32
6 516-023 3/8" SS Flat Washer 64
7 516-028 3/8" SS Nylock Nut 32
X.01
926-101
Champion Sq Picnic Table
SHEET 1 OF 2 REV.
A
SIZE

A
2
4
3
1
75
6
DETAIL A
SCALE 1 : 6
X.01
926-101
Champion Sq Picnic Table
SHEET 2 OF 2 REV.
A
SIZE
In Accordance to California law: WARNING This product contains a
chemical known to the State of California to cause cancer and birth
defects or other reproductive harm.

Part No. Description Qty.
642-111A/642-R11A 48” Champion Sq/Rnd Table
Top WO/ Umbrella Hole
1
622-019/622-R11 40” Champion Seat 4
632-101 Center Pedestal Post 1
632-102 Table Top Support 1
632-103 Seat Arms 2
632-104 Seat Supports 4
632-105 Seat Arm for 4’ Sq/Rd 1 Ped
Tbl
2
926-108/955-108
632-102632-104
632-101
632-105
The Table Top and Seats are not shown.
Periodic check of bolt tightness recommended.
632-103

926-108 Single Pedestal Direct Bury Square Ta-
ble
955-108 Single Pedestal Direct Bury Round Table
1 Bore a 12-14” diameter hole 36” into the ground.
2 Place 4-6” of pea rock in hole.
3 Place center pedestal post into the hole.
4 Drill out all holes with a 7/16” drill bit. Use a 1/2” drill bit for seat arm end plate holes
and center pedestal post holes at their union.
5 Bolt the support arms on to the center pedestal post using 1/2”x9” stainless steel hex
bolts.
6 Bolt seat supports on to the seat arms using 3/8”x2-1/2” stainless steel hex bolts.
7 Bolt table top support on to the center pedestal post using 3/8”x2-1/2” stainless steel hex
bolts.
8 Bolt the table top on to the table top support using 3/8”x1-1/2” stainless steel hex bolts.
9 Bolt the seats on to the seat supports using 3/8”x1-1/2” stainless steel hex bolts.
10 Level table and adjust to desired height. Recommended height is 20” from the ground to
the top of the seats.
11 Fill hole with concrete no higher than ground level.
Periodic check of bolt tightness recommended.
In Accordance to California law: WARNING This product contains a chemical known to the State of California to
cause cancer and birth defects or other reproductive harm.