Hanowa CT Series User manual

HANOWA
CT SERIES Custom Installation Manual
26CT, 165CT, 265CT
precision manufacturing·Precision Sound
The information in this manual contains selected equipment selected as well as accessories that have not installed as standard equipment.
Due to the different market areas, the choice of components may vary. HANOWA reserves the right to revise the services and products
described in this product manual without notice. Please refer to HANOWA’s official website for more up to date information
(www.hanowa-lab.com).
solton-acoustic.de
HANOWA
SOLTON Acoustic GmbH & Co. KG / Gewerbering 51.D-94060 Pocking.Germany
w w w . h a n o w a - l a b . c o m
Please take the time to follow the instructions in this owner's guide carefully. It will help you to properly use your new HANOWA product
and enjoy its features.
Please save this owner's guide for future reference.

Thank you for purchasing this CT series custom installation loudspeaker.
These products have been designed for dry-lined, stud partition walls and ceilings and
for suspended ceilings and will deliver many years of superb sound quality.
Introduction

Warning
Installation should be performed by an installer who is skilled in the proper use of hand and power tools,
knowledge of local building and fire codes, and who is familiar with the environment behind the wall or ceiling
where the speaker is being installed. No attempt should be made to install these loudspeakers unless you are
sure you will not be cutting through electric cables, water or gas pipes, or supporting joists. Ensure the loading on
the wall or ceiling will support the weight of these assemblies.
SAFETY INFORMATION
Important Safety Instructions
1. Read these instructions - for all components before using this product.
2. Keep these instructions - for future reference.
3. Heed all warnings - on the product and in the owner’s guide.
4. Follow all instructions.
5. Do not use this apparatus near water or moisture - Do not use this product near a bathtub, washbowl, kitchen sink, laundry
tub, in a wet basement, near a swimming pool, or anywhere else that water is present.
6. Clean only with a dry cloth . Unplug this product from the wall outlet before cleaning.
7. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus that produce heat.
8. Only use attachments/accessories specified by the manufacturer.
9. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
10. Unplug this apparatus during lightning storms or when unused for long periods of time - to prevent damage to this product.
11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way:
such as power supply cord or plug is damaged; liquid has been spilled or objects have fallen into the apparatus; the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped - Do not attempt to service this product
yourself. Opening the enclosure may expose you to dangerous voltages or other hazards. Please call us to be referred to an
authorized service center near you.
12. To prevent risk of fire or electric shock, avoid overloading wall outlets, extension cords, or integral convenience
receptacles.
13. Do not let objects or liquids enter the product - as they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock.
14. See product enclosure for safety-related markings.
STEP 1:
Cut the cutout template along the
dotted line and use a pencil to draw
the cutout aid along the edge of the
template.
STEP 2:
Speaker line connected to the rear
speaker terminals, "positive then
positive, negative then negative”.
STEP 3:
Stabilize the speaker with both
hands into the hole.
STEP 4:
Use a screwdriver to tighten the
screw clockwise to release the hand
after testing firmly, then cover the
net cover.
26CT
INSTALLATION STEPS
21

INSTALLATION STEPS
165CT
STEP 1:
Cut the cutout template along the
dotted line and use a pencil to draw
the cutout aid along the edge of the
template.
STEP 2:
Speaker line connected to the rear
speaker terminals, "positive then
positive, negative then negative”.
STEP 3:
Stabilize the speaker with both
hands into the hole.
STEP 4:
Use a screwdriver to tighten the
screw clockwise to release the hand
after testing firmly, then cover the
net cover.
265CT
INSTALLATION STEPS
STEP 1:
Cut the cutout template along the
dotted line and use a pencil to draw
the cutout aid along the edge of the
template.
STEP 2:
Speaker line connected to the rear
speaker terminals, "positive then
positive, negative then negative”.
STEP 3:
Stabilize the speaker with both
hands into the hole.
STEP 4:
Use a screwdriver to tighten the
screw clockwise to release the hand
after testing firmly, then cover the
net cover.
43

Specifications Specifications
Model
Type
Frequency Rating
Frequency Response
Proposed driving power
Maximum SPL output
Sensitivity (1W/1M)
Nominal Impedance
Dispersion
LF Drivers
HF Drivers
Dimensions (W*D*H)
Opening size:
Net Weight
Panel material:
colour:
26CT
6.5" two-way two-unit, round embedded
64-25000Hz (±10dB)
68-25000Hz (±3dB)
60
108dB
93dB
4Ω
360°
6.5" 30-core hand-coated
bamboo charcoal fiber compression basin.
Φ25 core ball top film treble
229mm*131mm(diameter * depth)
210mm*133mm (depth greater than 133mm) (diameter * depth)
2.25Kg
Styrene copolymer
Black panel / white mesh cover
165CT
6.5" two-way two-unit, square embedded
64-25000Hz (±10dB)
68-25000Hz (±3dB)
60
108dB
93dB
4Ω
150°
6.5" 30-core hand-coated
bamboo charcoal fiber compression basin.
Φ25 core ball top film treble
210mm*107*310mm
188mm*287mm (depth greater than 115mm)(W*H)
2.35Kg
Styrene copolymer
Black panel / white mesh cover
265CT
6.5" two-way three-unit, square embedded
58-25000Hz (±10dB)
62-25000Hz (±3dB)
80
110dB
 94dB
 4Ω
150°
6.5"*2, 30 core hand-coated
bamboo charcoal fiber pressing bowl.
Φ25 core ball top film treble
210mm*107*480mm
188mm*458mm (depth greater than 115mm)(W*H)
4.15Kg
Styrene copolymer
Black panel / white mesh cover
65

American Office
Office:775 Columbia Street, Brea, CA 92821
Telp： [phone]
MORIEN CO. LTD.
〒811-3111
Office:20-21 2-CHOME，HANAMIMINAMI，KOGA-CI，FUKUOKA，JAPAN.
ATTN: Mr. MORIZONO
TEL: [phone]
T A IW A N Of fi ce
ACESONIC TECHNOLOGY CO.，LTD.
Office:Minsheng east road, Taipei 10545 3 section 130 lane, lane no. 6
TEL: [phone]
C h i n a S A L E S
Office:No. 122 building，East Ring Road East Central Street,
Panyu District,GZ,China
TEL: :[phone] 3587
Germany Office
SOLTON Acoustic GmbH & Co. KG
Gewerbering 51
94060 Pocking
Germany
Tel [phone] / 91 38 80
Fax [phone] / 97 85 07
Japa n Offi ce
w w w . h a n o w a - l a b . c o m