Hans Grohe Talis Select E 110 71750007 Manual

ZH 用户手册/组装说明 2
EN Instructions for use / assembly instructions 3
Lesezeichen
中文 2
English 3
Talis Select S 80
72040007
Talis Select S 100
72042007
Talis Select E 110
71750007

2
中文
安装 (参见第页4)
安全技巧
装配时为避免挤压和切割受伤，必须戴上手
套。
本产品只允许作为洗浴、卫生和洁身之用。
冷热水管间过大的压力差必须予以平衡。
安装提示
• 安装前必须检查产品是否受到运输损害。安装
后将不认可运输损害或表面损伤。
• 管道和阀门必须根据通用标准进行安装、冲洗
和检查。
• 请遵守当地国家现行的安装规定。
• 只能按规定使用溢流阀。禁止将半露柱及其他
部件固定到溢流阀上。
• 如果使用即热式热水器时出现问题，或需要更
大的水流量时，可以将位于止回阀中的
EcoSmart®(流量限制器)拆除。
技术参数
本龙头配有 EcoSmart® (流量限制器)
工作压强： 最大1MPa
推荐工作压强： 0,1-0,5MPa
测试压强： 1,6MPa
(1MPa=10bar=147PSI)
热水温度： 最大70°C
推荐热水温度： 65°C
热力消毒: 最大70°C/4分钟
该产品专为饮用水设计！
符号说明
请勿使用含有乙酸的硅胶！
调节 (参见第页8)
热水温度调节。如果使用即热式喷头，则不建议
安装热水阀门。
保养 (参见第页7)
单向阀必须在符合国家或当地的法律的情况下按
照DINEN1717定期检查(至少一年一次)。
清洗 (参见第页10)
大小 (参见第页12)
流量示意图 (参见第页13)
带有EcoSmart®
无EcoSmart®
操作 (参见第页13)
汉斯格雅建议，清晨或在水流长时间停滞后，前
半升水不作饮用水使用。
备用零件 (参见第页14)
选装附件 (不在供货范围内)
• 专用工具#58085000(参见第页5)
• 水管胶泥(参见第页5)
• 垫圈#98996000(参见第页4)

3
English
Assembly (see page 4)
Safety Notes
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The product may only be used for bathing, hygienic
and body cleaning purposes.
The hot and cold supplies must be of equal
pressures.
Installation Instructions
• Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
• The pipes and the fixture must be installed, flushed
and tested as per the applicable standards.
• The plumbing codes applicable in the respective
countries must be observed.
• The drain valve must only be used as intended. It is
not allowed to attach other objects to the drain
valve, for example a semi-pedestal.
• The EcoSmart® (flow limiter) in the adapter bottom
can be removed if there are problems with the flow
heater or when more water flow is required.
Technical Data
This mixer series-produced with EcoSmart®
(flow limiter)
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 70°C
Recommended hot water temp.: 65°C
Thermal disinfection: max. 70°C / 4 min
The product is exclusively designed for drinking water!
Symbol description
Do not use silicone containing acetic acid!
Adjustment (see page 8)
To adjust the hot water limiter. Using a hot water limiter
in combination with a continuous flow water heater is
not recommended.
Maintenance (see page 7)
The check valves must be checked regularly according
to DIN EN 1717 in accordance with national or
regional regulations (at least once a year).
Cleaning (see page 10)
Dimensions (see page 12)
Flow diagram (see page 13)
 with EcoSmart®
 without EcoSmart®
Operation (see page 13)
Hansgrohe recommends not to use as drinking water
the first half liter of water drawn in the morning or after
a prolonged period of non-use.
Spare parts (see page 14)
Special accessories (order as an extra)
• special tool #58085000 (see page 5)
• Installation putty (see page5)
• seal #98996000 (see page 4)

4
5 6
> 4 mm
< 4 mm
4
2
3
(7 Nm)
1
1.
2.
98996000
Montage / Dichtung

5
SW 19 mm
(4 Nm)
SW 10 mm
58085000
(max.
7 Nm)
58085000
(max.
7 Nm)
11 12
13 11
8
910
13
7
2.
1.
SW 24 mm
(4 Nm)
InstallationskittMontageschlüssel

6
(50 Ncm)
13 14
17 18
15 16
> 2 min
SW 22 mm
SW 22 mm
(2 Nm)
Montage

7
SW 19 mm
SW 19 mm
(4 Nm)
SW 10 mm
SW 10 mm
1 2
3 4
5
Wartung

8
2
3
1
4 5
60 °C
10 °C
6
35°C
39°C
43°C
47°C
57°C
60°C
0,3 MPa
Justierung Justierung

9
7
8 9
(0,5 Nm)
最大 / max. 至少 /min.
Justierung

10
•
•
•
•
•
•
•
•
•
•
•
Hansgrohe
Hansgrohe
www.hansgrohe-int.com/guarantee
QuickClean
QuickClean
10
QUICK
CLEAN
Reinigung