Hans Grohe Raindance Connect Showerpipe 27164001 Installation guide

Raindance Connect
Showerpipe
27164001
Installation Instructions / Warranty

2
Raindance Connect Showerpipe
27164001
Suggested installation

3
Technical Information
Max. water pressure 147 psi
Recommended water pressure 29 - 72 psi
Test pressure 232 psi
Max. flow rate
showerhead 2.5 gpm
handshower 2.5 gpm
Recommended tools (not included)
grease pencil or other marking tool
level
ruler
2 & 3 mm Allen wrenches
6 mm drill bit
8 mm wrench
Philips screwdriver
waterproof sealant






2 mm
3 mm
6 mm
8 mm
Installation Considerations
This unit does not include a water
supply. Use Hansgrohe model
27458XX3 or another supply that
complies with ASME A112.18.1/CSA
B215.1 including ASME A112.18.3.
dense natural stone
brick
gypsum wallboard/plaster fiberboard
surfaced with tile, marble, or stone
If this product is to be installed on another type
of wall, such as a fiberglass or acrylic shower
enclosure, please contact the manufacturer of
the enclosure for recommendations regarding
suitable mounting hardware, mounting
locations, and reinforcement.
In Massachusetts, the maximum output
temperature of the shower mixing valve can be
no higher than 112ºF.
•
•
•
The installer should be sure that the mounting
location for this product is flat (no projecting
joints or tiles) and that the wall is suitable for
the installation of this product.
The included mounting hardware is suitable for
solid surface walls, such as:
concrete
concrete wallboard
•
•

4
Installation
Drill the screw holes with a 6 mm bit.
Install the anchors.
If both ends of the showerpipe are mounted on tile,
install the top and bottom mounting wall flanges.

5
If the bottom of the showerpipe is mounted on tile, but
the top is not, install the top wall flange with the tile
matching disk.
Push the shower arm and lower support into the ends of
the riser. Install the escutcheons.
Push the showerpipe assembly over the wall flanges.
Tighten the set screws with a 3 mm Allen wrench.

6
Install the showerhead on the shower arm.
Use a level to make sure that the shower arm is straight.
If it is not, loosen the mounting screws slightly with an 8
mm wrench. Reposition the arm until it is straight. Tighten
the mounting screws.
Attach the escutcheons to the flanges by rotating them
clockwise.

7
Tighten the shower arm safety screw with a 2 mm
Allen wrench.
Place a hose washer in one end of the hose. Connect
this end to the water supply (not included).
Adjust the slider
To make the slider easier to move up and down the bar,
turn the screw counter-clockwise.
To make it harder to move, turn the screw clockwise.
Place the screen washer in the other end of the hose.
Connect this end to the handshower.
This unit does not include a water
supply. Use Hansgrohe model
27458XX3 or another supply that
complies with ASME A112.18.1/
CSA B215.1 including ASME
A112.18.3.
harder
easier

8
User instructions
When the water is turned on, it will come from the
handshower.
To use the showerhead, push the handshower up into the
handshower holder on the bottom of the showerpipe.
To remove the handshower from the showerpipe, push
downwards on the holder (1), then pull the handshower
down and out of the pipe(2).
Approximately 1 quart of water will come from the
bottom of the showerpipe when the handshower is
removed.
1
2

9
Scale removal
The showerhead and the handshower use the Quick
Clean™ cleaning system. If scale deposits are noticed
in the spray channels, turn the water on lightly and
rub across the channels with a finger or a sponge to
dislodge them.
To remove scale deposits from the showerhead spray
face, pour about 3/4” of a commercial scale remover*,
such as Lime-Away™ or CLR™, into a shallow dish.
Soak the spray face for the amount of time shown in the
label instructions.
Rinse the showerhead with clear water.
Install the showerhead. Flush it with clear water for at
least one minute.

10
Replacement Parts
1 hose 28255000
2 slider 98714000
3 riser 96770000
4 escutcheon 98672000
5 wall flange 98673000
6 shower arm 98675000
7 screen washer 94246000
8 showerhead 98855001
9 handshower 98715001
10 mounting kit 98716000
11 tile-matching-disk 98681000
12 escutcheon 98739000
13 handshower holder 98821000
1
2
6
3
4
10
9
10x1,5
15x2,5
10x1,5
15x2,5
8
7
15x2,5
5
12
10
5
13
11
5
10