Hanwha Vision SMT-1031PV User manual

PUBLIC VIEW MONITOR
SMT-1031PV
SMT-1031PVW
SMT-2731PV
SMT-3231PV

SAFETY INSTRUCTIONS
1. WARNING
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
Do not insert any metallic object through the ventilation grills or other openings on the equipment.
Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installa-
tion instructions.
2. CAUTION
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE REAR COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
3. EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of “dangerous voltage: within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
ATTENTION
IL Y A RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE TYPE INCORRECT.
METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.
※This device has been verified using STP cable. The use of appropriate GND grounding and STP cable
is recommended to effectively protect your product and property from transient voltage, thunderstroke,
communication interruption.
※Select an installation site that can hold at least 4 times the monitor weight.

English _3
CONTENTS
OVERVIEW
4
4Package Contents
4Separately sold product
5Names and functions of each part(SMT-
1031PV/SMT-1031PVW)
8Names and functions of each part(SMT-
2731PV/SMT-3231PV)
11 Remote control
CONNECTING WITH OTHER DEVICE
12
12 Things to check before connection
12 Connecting with external devices
MENU SETTINGS
14
14 OSD Menu setting (SMT-1031PV/SMT-
1031PVW)
16 OSD Menu setting (SMT-2731PV/SMT-
3231PV)
NETWORK CONNECTION AND SETUP &
WEBVIEWER
23
23 Connecting the PVM Directly to Local Area
Networking
24 Connecting the PVM Directly to a DHCP
Based DSL/Cable Modem
25 Using Device Manager
25 Automatically searching camera
25 Configuring IP address
27 Manually registering camera
28 Automatically configuring IP
28 Port Range Forward (Port Mapping) Setup
30 Connecting to the Camera from a Shared
Local PC
30 Connecting to the Camera from a Remote
PC via the Internet
30 Connecting to the Camera
32 Password setting
32 Login
32 Camera Web Viewer Setup
SETUP SCREEN
33
33 Setup
33 Hallway view
34 Creating a text overlay
35 PVM setup
37 Setting alarm input
APPENDIX
41
41 Mechanical
44 Troubleshooting

4_ overview
overview
PACKAGE CONTENTS
Please check the following contents are included in addition to the main unit.
Public View Monitor Quick Start Guide Alarm terminal block
COLORTEMP
CAMERA
HDMI2 INPUTHDMI1
PIP.SIZEPIP.INPUT
PIP.SWAPPIP.LOC
ASPECT MODE
VOL- VOL+
Remote Controller Battery Power Inverter Harness
SEPARATELY SOLD PRODUCT
Appearance Item Name Description Model Name
HPoE Injector Connects power supply
and network SPO-8315
Adpater DC 24V power supply SPU-60240
The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802.3bt shall be a
UL Listed device with the output evaluated as a Limited Power Source as defined in UL60950-1 or PS2 as
defined in UL62368-1.
overview

English _5
NAMES AND FUNCTIONS OF EACH PART(SMT-1031PV/SMT-1031PVW)
Front
bd
ac
Name Description of functions
a
Camera Lens IP camera is installed.
b
ALARM LED Displayed when an alarm output occurs.
c
LED
Displays the power ON/OFF status.
ON – GREEN
OFF – RED
d
IR Receiver Receive IR signal from Remote Controller.

6_ overview
overview
Back
a b c d
e f
Name Description of functions
a
24V This is the DC 24V Power input terminal.
b
USB Connect the USB Devices for Monitor F/W update.
c
ALARM ALARM signal input / output
d
HPoE (or PoE+) Used to connect the HPoE or Ethernet cable for network connection.
e
Micro SD card slot Compartment for the Micro SD card.
f
RESET Resets the camera installed in the monitor to its factory default settings.
` If you forget your password, use the RESET button.

English _7
M ` Remove the terminal cover by pushing the fixing hook, and then remove the SD card cover by loosening the
screws counterclockwise.
<Top> <Bottom>
` This product is intended to be supplied by a UL Listed Power Supply Unit marked “Class 2” or “LPS” or
“PS2”.
` This product dose not support LLDP.

8_ overview
overview
NAMES AND FUNCTIONS OF EACH PART(SMT-2731PV/SMT-3231PV)
Front
ab c d
Name Description of functions
a
Camera Lens IP camera is installed.
b
ALARM LED Displayed when an alarm output occurs.
c
LED
Displays the power ON/OFF status.
ON – GREEN
OFF – RED
d
IR Receiver Receive IR signal from Remote Controller.

English _9
Back
a b c d e f
*COVER OPEN
g h

10_ overview
overview
Name Description of functions
a
24V This is the DC 24V Power input terminal.
b
ALARM ALARM signal input / output
c
HPoE Used to connect the HPoE or Ethernet cable for network connection.
d
USB Connect the USB Devices for Monitor F/W update.
e
HDMI1
PIP/PBP HDMI Input terminal for PIP/PBP
f
HDMI2 HDMI Input terminal (not support PIP/PBP in Web viewer)
g
RESET Resets the camera installed in the monitor to its factory default settings.
` If you forget your password, use the RESET button.
h
Micro SD card slot Compartment for the Micro SD card.
M ` While the monitor outputs video sources from both HDMI1 and HDMI2, audio source is supported from
HDMI1.
` The menu button on the remote control works only when the video (Camera, HDMI1, HDMI2) appears on the
monitor's main screen (PIP: large screen, PBP: screen on the left).
` If there is no output signal (black screen) on the monitor, press the [ENTER] button on the remote control to
check and change the input source type.
` Detach the terminal cover by rotating the fastening screw in a counterclockwise direction to loosen it, then
connect the cable.
` This product is intended to be supplied by a UL Listed Power Supply Unit marked “Class 2” or “LPS” or
“PS2”.
` This product dose not support LLDP.

English _11
REMOTE CONTROL
M ` Those buttons without specific description are deprecated buttons.
COLOR TEMP
CAMERA
HDMI2 INPUTHDMI1
PIP.SIZEPIP.INPUT
PIP.SWAPPIP.LOC
ASPECT MODE
VOL- VOL+
HDMI1
Select HDMI1 mode
(SMT-2731PV/SMT-3231PV only)
HDMI2
Select HDMI2 mode
(SMT-2731PV/SMT-3231PV only)
CAMERA
Select internal IP camera
ASPECT
Changes the screen size.
MENU/EXIT
Activate and exit the OSD menu
MUTE
Press to mute the sound temporarily.
(SMT-2731PV/SMT-3231PV only)
POWER
Turn ON / OFF the monitor
INPUT
Select the input signal of the main
screen. (HDMI1/HDMI2/CAMERA)
(SMT-2731PV/SMT-3231PV only)
COLOR TEMP
Select the color temperature Warm/Normal/
Cool/USER.
PIP.SIZE
Adjust the size of the sub-screen in PIP mode.
(SMT-2731PV/SMT-3231PV only)
PIP.SWAP
Swaps the Main/sub screens when PIP mode
active. (SMT-2731PV/SMT-3231PV only)
PIP. INPUT
Select sub-screen in PIP/PBP mode
(SMT-2731PV/SMT-3231PV only)
PIP.LOC
Adjust the position of the sub-screen
in PIP mode.
(SMT-2731PV/SMT-3231PV only)
MODE
Pressing the button swaps the multiscreen in
the order of SINGLE > PIP > PBP.
(SMT-2731PV/SMT-3231PV only)
_+$%buttons
Moves from one menu item to another
horizontally, vertically or adjusts selected
menu values.
ENTER
Activates a highlighted menu item.
VOL -, +
Adjusts the volume.
(SMT-2731PV/SMT-3231PV only)

12_ connecting with other device
connecting with other deviceconnecting with other device
THINGS TO CHECK BEFORE CONNECTION
Check before connecting
J ` When connecting, refer to the instruction manual of the product to be connected. The number and position
of external devices may differ depending on the product.
` Do not connect the power until all connections are complete. Connecting the power supply during
connection may damage the product.
` Check the type of terminal behind the product you want to connect.
CONNECTING WITH EXTERNAL DEVICES
HDMI cable connection method
HDMI
or

English _13
Powering and networking
HPoE
Router or switching hub
(HPoE supported)

14_ menu settings
menu settings
OSD MENU SETTING (SMT-1031PV/SMT-1031PVW)
Selecting OSD menu
You can select the OSD menu by pressing the [MENU/EXIT] button on the remote controller.
1. Press the _/+buttons to select the main menu
2. Press the $/%buttons to select the sub-menu, and then press the ENTER.
3. Press the $/%/_/+buttons to adjust the adjustment value.
4. Press the MENU/EXIT button to exit.
Picture Menu
1. Press the MENU/EXIT button to enter the main menu.
2. Press the _/+button to select <PICTURE>, and then press the ENTER.
3. The PICTURE Menu can be selected from the following 3 modes by pressing $/%buttons.
PICTURE
Picture Mode Standard
Color Temperature Medium
Aspect Ratio Auto
~Picture Mode : Adjust setting of the picture. Picture Mode can select 4 modes as Standard, Soft,
User and Vivid.
Three of the four modes except for User mode are shipped with fixed values at the
time of shipment from the factory.
~Color Temperature : The color temperature can be adjusted and used depending on the monitor
color. Color Temperature can select 4 modes as Cool, Medium, Warm and User.
Three modes except User mode are factory shipped with factory default values,
and each color item (Red, Green, Blue) is selected with the $/%buttons in the
User mode only.
~Aspect Ratio : You can select a screen size you want. (Auto/4:3/16:9)

English _15
Option Menu
1. Press the MENU/EXIT button to enter the main menu.
2. Press the _/+button to select <OPTION>, and then press the ENTER.
3. The Option Menu can be selected from the following 3 modes by pressing $/%buttons.
OPTION
OSD Language English
Restore Factory Default
Software Update(USB)
~OSD Language : Select the screen language. (English/Espanol/Francais)
~Restore Factory Default : Resets the monitor to its factory default settings.
~Software Update(USB) : The monitor can be updated by connecting a USB to the USB port.

16_ menu settings
menu settings
OSD MENU SETTING (SMT-2731PV/SMT-3231PV)
Selecting OSD menu
You can select the OSD menu by pressing the [MENU/EXIT] button on the remote controller.
1. Press the MENU/EXIT button to enter the main menu.
2. Press the $/%buttons to select the main menu, and then press the ENTER or +button.
3. Press the $/%buttons to select the sub-menu, and then press the ENTER or +button.
4. Press the $/%buttons to adjust the adjustment value.
5. Press the MENU/EXIT button to exit.
Input Source
1. Press the MENU/EXIT button to enter the main menu.
2. Press the $/%button to select <Input Source>, and then press the ENTER or +button.
CAMERA
Input Source
Brightness/Contrast
Color Setting
Picture Quality Setting
Display
Audio
Multi-Window
OSD
Other
HDMI1
HDMI2
•CAMERA
Window1:
InputSource: CAMERA
Resolution: 1920x1080@60Hz
Resolution: 1920x1080@60Hz
Window2:
InputSource:
Resolution:
~HDMI 1 : Select external HDMI1 input
~HDMI 2 : Select external HDMI2 input
~CAMERA : Select internal Camera input

English _17
Brightness/Contrast
1. Press the MENU/EXIT button to enter the main menu.
2. Press the $/%button to select <Brightness/Contrast>, and then press the ENTER or +button.
CAMERA
Input Source
Brightness/Contrast
Color Setting
Picture Quality Setting
Display
Audio
Multi-Window
OSD
Other
Brightness
Contrast
Window1:
InputSource: CAMERA
Resolution: 1920x1080@60Hz
Resolution: 1920x1080@60Hz
80
50
Window2:
InputSource:
Resolution:
~Brightness : Adjusts the brightness of the screen. (Adjust 0 ~ 100)
~ Contrast : Adjusts the difference in brightness between the object and the environment. (Adjust 0 ~ 100)
Color Setting
1. Press the MENU/EXIT button to enter the main menu.
2. Press the $/%button to select <Color Setting>, and then press the ENTER or +button.
CAMERA
Input Source
Brightness/Contrast
Color Setting
Picture Quality Setting
Display
Audio
Multi-Window
OSD
Other
Gamma
Picture Mode
Color Temperature
Hue
Saturation
Window1:
InputSource: CAMERA
Resolution: 1920x1080@60Hz
Resolution: 1920x1080@60Hz
2.2
Standard
Normal
50
50
Window2:
InputSource:
Resolution:

18_ menu settings
menu settings
~Gamma : Adjust the mid-range brightness (Gamma) of the screen.(1.8/2.0/2.2/2.4/2.6)
~
Picture Mode : Select a screen mode appropriate for your viewing environment. (Standard/Photo/
Movie/Game)
~Color Temp. : The color temperature can be adjusted and used depending on the monitor color.
(Warm/Normal/Cool/USER)
~Hue : Adjusts the color of the screen. (Adjust 0 ~ 100)
~Saturation : Adjusts the saturation of the screen. (Adjust 0 ~ 100)
Picture Quality Setting
1. Press the MENU/EXIT button to enter the main menu.
2. Press the $/%button to select <Picture Quality Setting>, and then press the ENTER or +button.
CAMERA
Input Source
Brightness/Contrast
Color Setting
Picture Quality Setting
Display
Audio
Multi-Window
OSD
Other
Sharpness
Window1:
InputSource: CAMERA
Resolution: 1920x1080@60Hz
Resolution: 1920x1080@60Hz
30
Window2:
InputSource:
Resolution:
~Sharpness : Adjusts the sharpness of the screen. (Adjust 0 ~ 100)

English _19
Display
1. Press the MENU/EXIT button to enter the main menu.
2. Press the $/%button to select <Display>, and then press the ENTER or +button.
CAMERA
Input Source
Brightness/Contrast
Color Setting
Picture Quality Setting
Display
Audio
Multi-Window
OSD
Other
Aspect Ratio
Window1:
InputSource: CAMERA
Resolution: 1920x1080@60Hz
Resolution: 1920x1080@60Hz
Wide Screen
Window2:
InputSource:
Resolution:
~Aspect Ratio : You can select a screen size you want. (Wide Screen/4:3/1:1/Auto)
Audio
1. Press the MENU/EXIT button to enter the main menu.
2. Press the $/%button to select <Audio>, and then press the ENTER or +button.
CAMERA
Input Source
Brightness/Contrast
Color Setting
Picture Quality Setting
Display
Audio
Multi-Window
OSD
Other
Mute
Volume
Window1:
InputSource: CAMERA
Resolution: 1920x1080@60Hz
Resolution: 1920x1080@60Hz
off
50
Window2:
InputSource:
Resolution:
~Mute : You can set whether to use the mute function. (On/Off)
~Volume : You can adjust the volume. (Adjust 0 ~ 100)

20_ menu settings
menu settings
Multi-Window
1. Press the MENU/EXIT button to enter the main menu.
2. Press the $/%button to select <Multi-Window>, and then press the ENTER or +button.
CAMERA
Input Source
Brightness/Contrast
Color Setting
Picture Quality Setting
Display
Audio
Multi-Window
OSD
Other
Multi-Window
Sub Win2 Input
PIP Size
PIP Position
Swap
Window1:
InputSource: CAMERA
Resolution: 1920x1080@60Hz
Resolution: 1920x1080@60Hz
Off
CAMERA
Large
BottomRight
Window2:
InputSource:
Resolution:
~Multi-Window : You can select Picture in Picture (PIP) or Picture by Picture (PBP) mode.
(Off/PIP Mode/PBP 2Win)
~Sub Win2 Input : Displays the currently output Sub Win2 Input. (HDMI1/HDMI2/CAMERA)
~PIP Size : You can adjust the size of the sub-screen in PIP mode. (Small/Medium/Large)
~PIP Position : You can adjust the position of the sub-screen in PIP mode. (TopRight/TopLeft/
BottomRight/BottomLeft)
~Swap : You can switch between the main screen and sub-screen in PIP or PBP mode.