Harman Kardon AVR 260 User manual

harman/kardon Service Manual
AVR 260/230
7 x 50W 7.1 CHANNEL A/V RECEIVER
CONTENTS
EXPLODED VIEW AND PARTS 14
ELECTRICAL PARTS LIST 15
SEMICONDUCTOR PINOUTS 49
PCB DRAWINGS 109
BLOCK DIAGRAM 116
WIRING DIAGRAM 117
AMP BIAS ADJUSTMENT 118
SCHEMATIC DIAGRAMS 119-131
ESD WARNING 2
FRONT AND REAR PANELS 3
REMOTE CONTROL 8
TROUBLESHOOTING GUIDE 10
PROCESSOR RESET 10
BASIC SPECIFICATIONS 11
PACKAGE LISTS AND PARTS 12
DISASSEMBLY 13
Released EU2010 Harman Consumer Group, Inc. Rev 0, 07/2010
8500 Balboa Boulevard
Northridge, California 91329
harman/kardon
AVR 260/230 Service Manual
Page 1 of 131

Each precaution in this manual should be followed during servicing.
Components identified with the IEC symbol in the parts list are special significance to safety. When replacing a component identified with
, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the
parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably
insulated from the supply circuit before retuming the product to the customer.
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and
semiconductor "chip" components.
The following techniques should be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on
your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to
prevent electrostatic charge build-up or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges
sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement
ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the
chassis or circuit assembly into which the device will be installed.
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together
or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.
CAUTION :
harman/kardon
AVR 260/230 Service Manual
Page 2 of 131

CompositeAnalog
AVRInfo Resolution Audio EffectsVideo ModesSurround ModesBack/ExitSource List
MN LK OK
260
BCD �
216789AE45J
I
GH3
F
5
4
FRONT-PANEL CONTROLS
0 Volume Control :Turn this knob clockwise to increase the volume,
counterclockwise to decrease the volume. If the AVR is muted, adjusting
volume control will automatically release the unit from the silenced
condition.
1 System Power Control :When the Main Power Switch on the rear
panel is“ON,”press this button to turn on the AVR; press it again to turn
the unit off (to Standby). Note that the Power Indicator
2 will turn
white when the unit is on.
2 Power Indicator :This LED will be illuminated in amber when the
unit is in the Standby mode to signal that the unit is ready to be turned
on.When the unit is in operation, the indicator will turn white.
3 Headphone Jack :This jack may be used to listen to the AVR’s
output through a pair of headphones. Be certain that the headphones
have a standard 6,3 mm stereo phone plug. Note that the speakers will
automatically be turned off when the headphones are connected.
When configuring your system using EzSet/EQ, the calibration
microphone should be plugged into this jack using the supplied adaptor
that converts the small mini-plug at the end of the microphone’s cord to
a 6,3 mm plug.
4 Navigation :These buttons are used to navigate the AVR’s menus and
to operate the tuner.
5 OK Button : Press this button to select the currently highlighted item.
6 AVR Settings Button : Press this button to access the AVR’s main
menu.
7 Info Settings Button : Press this button to directly access the AVR’s
Setup Source submenu, which contains the settings for the current
source.
8 Resolution : Pressing this Button once and then using the
KL
Buttons
4 changes the AVR’s video output resolution to these settings:
576i, 576p, 720p, 1080i or 1080p.The AVR is set to default to 576i when
first switched on, or if you reset it later. This resolution has been chosen
to ensure that the On Screen Display information is visible on yourTV
even with analog S-Video or Composite (CVBS) signals. Having selected
the best resolution for your system, confirm with the
OK Button 5 .
The Front Panel Display now shows "Res Change, Cancel". If you press OK
now, or do nothing for 20 seconds, the AVR returns to normal play mode.
To confirm the new resolution, press the
L
Button 4 , which changes
the Display from "Cancel" to "Accept", then press the
OK Button 5 .The
new resolution is now in use.
9 Audio Effects : Press this button to directly access the Audio Effects
submenu, which allows adjustment of the tone and other controls. See
the Initial Setup section for more information.
A Video Modes : Press this button for direct access to theVideo Modes
submenu, which contains settings that may be used to improve the
picture if necessary after you have adjusted the picture settings using
the video display orTV.
B Remote Sensor Window :The sensor behind this window receives
infrared signals from the remote control. Aim the remote at this area
and do not block or cover it unless an external remote sensor is installed.
C Main Information Display :This display delivers messages and
status indications to help you operate the receiver.
harman/kardon
AVR 260/230 Service Manual
Page 3 of 131

7
ENGLISH
FRONT-PANEL CONTROLS
D Speaker/Channel Input Indicators :These indicators are
multipurpose, indicating either the speaker type selected for each
channel or the incoming data-signal configuration.The left, center,
right, right surround and left surround speaker indicators are composed
of three boxes, while the subwoofer is a single box.The center box lights
when a“Small”speaker is selected, and the two outer boxes light when
“Large”speakers are selected.When none of the boxes are lit for the
center, surround or subwoofer channels, no speaker has been selected
for that position. (See page 20 for more information on configuring
speakers.)The letters inside each of the center boxes display active
input channels. For standard analog inputs, only the L and R will light,
indicating a stereo input.When a digital source is playing, the indicators
will light to display the channels being received at the digital input.
When the letters flash, the digital input has been interrupted.
(See page 31 for more information on the Channel Indicators).
NOTE :When you have reassigned the surround back speakers to the
remote zone using the
MULTIROOMSETUP menu, the boxes that indicate
the presence of the surround back speakers will automatically disappear,
reflecting the fact that the main listening area is now configured for
5.1-channel operation. (See page 33 for more information on reassigning
the surround back speakers for multiroom use.)
E Surround Modes : Press this button to select a surround sound
(e.g.,multichannel) mode.The Surround Modes menu will appear on
screen, and the menu line will appear on the lower line of the front-
panel display.
Use the front-panel or remote
KL
Buttons to highlight a different
menu line: Auto Select,Virtual Surround, Stereo, Movie, Music or Video
Game. Each line represents a type of audio signal, and is set to the
surround mode the AVR will automatically select when it detects the
audio signal.
You may manually select a different mode for each type of audio. Press
the
OK Button when the menu line is highlighted, and the available
surround mode options for the current signal will appear. Use the
KL
Buttons to select the desired mode, and press the
OK Button to engage
it. Press the Back/Exit Button to exit the Surround Modes menu and
display the next higher menu in the hierarchy.
See the Advanced Functions section for more information on surround
modes.
F Back/Exit : Press this button to return to the previous menu.When the
main AVR menu is displayed, press this button to exit the menu system.
G Digital Optical Front Input : Connect the optical digital audio
output of an audio or video product to this jack.
H Digital Coax Front Input :This jack is normally used for connection
to the output of portable digital audio devices, video game consoles or
other products that have a coax digital jack.
I Video Front Input Jacks :These audio/video jacks may be used for
temporary connection to video games or portable audio/video products
such as camcorders and portable audio players.
J Source List : Press this button to select a source device, which is a
component where a playback signal originates, e.g., DVD.
harman/kardon
AVR 260/230 Service Manual
Page 4 of 131

6
CompositeAnalog
AVRInfo Resolution Audio EffectsVideo ModesSurround ModesBack/ExitSource List
MN LK OK
260
BCD �
216789AE45J
I
GH3
F
5
4
FRONT-PANEL CONTROLS
0 Volume Control :Turn this knob clockwise to increase the volume,
counterclockwise to decrease the volume. If the AVR is muted, adjusting
volume control will automatically release the unit from the silenced
condition.
1 System Power Control :When the Main Power Switch on the rear
panel is“ON,”press this button to turn on the AVR; press it again to turn
the unit off (to Standby). Note that the Power Indicator
2 will turn
white when the unit is on.
2 Power Indicator :This LED will be illuminated in amber when the
unit is in the Standby mode to signal that the unit is ready to be turned
on.When the unit is in operation, the indicator will turn white.
3 Headphone Jack :This jack may be used to listen to the AVR’s
output through a pair of headphones. Be certain that the headphones
have a standard 6,3 mm stereo phone plug. Note that the speakers will
automatically be turned off when the headphones are connected.
When configuring your system using EzSet/EQ, the calibration
microphone should be plugged into this jack using the supplied adaptor
that converts the small mini-plug at the end of the microphone’s cord to
a 6,3 mm plug.
4 Navigation :These buttons are used to navigate the AVR’s menus and
to operate the tuner.
5 OK Button : Press this button to select the currently highlighted item.
6 AVR Settings Button : Press this button to access the AVR’s main
menu.
7 Info Settings Button : Press this button to directly access the AVR’s
Setup Source submenu, which contains the settings for the current
source.
8 Resolution : Pressing this Button once and then using the
KL
Buttons
4 changes the AVR’s video output resolution to these settings:
576i, 576p, 720p, 1080i or 1080p.The AVR is set to default to 576i when
first switched on, or if you reset it later. This resolution has been chosen
to ensure that the On Screen Display information is visible on yourTV
even with analog S-Video or Composite (CVBS) signals. Having selected
the best resolution for your system, confirm with the
OK Button 5 .
The Front Panel Display now shows "Res Change, Cancel". If you press OK
now, or do nothing for 20 seconds, the AVR returns to normal play mode.
To confirm the new resolution, press the
L
Button 4 , which changes
the Display from "Cancel" to "Accept", then press the
OK Button 5 .The
new resolution is now in use.
9 Audio Effects : Press this button to directly access the Audio Effects
submenu, which allows adjustment of the tone and other controls. See
the Initial Setup section for more information.
A Video Modes : Press this button for direct access to theVideo Modes
submenu, which contains settings that may be used to improve the
picture if necessary after you have adjusted the picture settings using
the video display orTV.
B Remote Sensor Window :The sensor behind this window receives
infrared signals from the remote control. Aim the remote at this area
and do not block or cover it unless an external remote sensor is installed.
C Main Information Display :This display delivers messages and
status indications to help you operate the receiver.
harman/kardon
AVR 260/230 Service Manual
Page 5 of 131

9
ENGLISH
REAR-PANEL CONNECTIONS
C
RS-232 Reset: This switch is only used during a software upgrade. A
standard processor reset is performed by pressing and holding the front-
panel OK Button while the receiver is in Standby.
D
Front Speaker Outputs: Connect these outputs to the matching
+ or – terminals on your left and right speakers. In conformance with
the new CEA color code specification, theWhite terminal is the positive,
or "+" terminal that should be connected to the red (+) terminal on
Front Left speaker with the older color coding, while the Red terminal
is the positive, or "+" terminal that should be connected to the red (+)
terminal on Front Right speaker. Connect the black (–) terminals on the
AVR to the black (–) terminals on the speakers. See page 15 for more
information on speaker polarity.
E
Center Speaker Outputs: Connect these outputs to the matching
+ and – terminals on your center channel speaker. In conformance with
the new CEA color code specification, the GreenTerminal is the positive,
or "+" terminal that should be connected to the red (+) terminal on
speakers with the older color coding. Connect the black (–) terminal on
the AVR to the black negative (–) terminal on your speaker. (See page
15 for more information on speaker polarity.)
F
Surround Speaker Outputs: Connect these outputs to the
matching + and – terminals on your surround channel speakers. In
conformance with the new CEA color code specification, the Blue
terminal is the positive, or "+" terminal that should be connected to the
red (+) terminal on the Surround Left speaker with older color coding,
while the Gray terminal should be connected to the red (+) terminal
on the Surround Right speaker with the older color coding. Connect
the black (–) terminal on the AVR to the matching black negative (–)
terminals for each surround speaker. (See page 15 for more information
on speaker polarity.)
G
Switched AC Accessory Outlet: This outlet may be used to power
any device that you wish to have turn on when the AVR is turned on
with the System Power Control switch
1 .
H
RS-232 Serial Port: This specialized connector may be used with
your personal computer in case Harman Kardon offers a software
upgrade for the receiver at some time in the future. Leave the Mode
switch
M
popped out in the Operate position, unless the AVR is being
upgraded.The Reset switch
C
is used only during the upgrade process.
I
AC Power Cord: Connect the AC plug to an unswitched AC wall
output.
J
Video 2 Component Video Inputs: These inputs may be
used with any source device equipped with analogY/Pr/Pb or RGB
component video outputs. Do not use these inputs if HDMI connection is
possible, use the HDMI inputs instead.
K
Monitor Component Video Outputs: Connect these outputs
to the component video inputs of a video projector or monitor. When
a source connected to one of the two ComponentVideo Inputs
JL
is
selected the signal will be sent to these jacks.
L
Video 1 Component Video Inputs: These inputs may be
used with any source device equipped with analogY/Pr/Pb or RGB
component video outputs Do not use these inputs if HDMI connection is
possible, use the HDMI inputs instead.
Note: All component inputs/outputs can be used for RGB signals too, in
the same way as described for theY/Pr/Pb signals, then connected to the
jacks with the corresponding color. RGB connection is not possible if the
source outputs a separate sync signal.
M
Update Mode Button: Leave the Mode switch popped out in the
Operate position, unless the AVR is being upgraded.The Reset switch
C
is used only during the upgrade process.
N
Coaxial Digital Inputs: Connect the coax digital output from a DVD
player, HDTV receiver, the output of a compatible computer sound card
playing MP3 files or streams, LD player, MD player or CD player to these
jacks.The signal may be either a Dolby Digital signal, DTS signal, a 2
channel MPEG 1 signal, or a standard PCM digital source. Do not connect
the RF digital output of an LD player to these jacks.
O
Surround Back/Multiroom Speaker Outputs: These speaker
terminals are normally used to power the surround back left/surround
back right speakers in a 7.1 channel system. However, they may also
be used to power the speakers in a second zone, which will receive the
output selected for a multiroom system.
To change the output fed to these terminals from the default of the
Surround Back speakers to the Multiroom Output, you must change
a setting in the
MultiroomMenu of the OSD system. See page 33
for more information on configuring this speaker output. In normal
surround system use, the brown and black terminals are the surround
back left channel positive (+) and negative (–) connections and the
tan and black terminals are the surround back right positive (+) and
negative (–) terminals.
For multiroom use, connect the brown and black SBL terminals to the
red and black connections on the left remote zone speaker and connect
the tan and black SBR terminals to the red and black terminals on the
right remote zone speaker.
harman/kardon
AVR 260/230 Service Manual
Page 6 of 131

10
REAR-PANEL CONNECTIONS
P
Video 1 Video Outputs: Connect these jacks to the RECORD/INPUT
composite or S-Video jack on aVCR.
Q
Video 1 Video Inputs: Connect these jacks to the PLAY/OUT
composite or S-Video jacks on aTV or other video source.
R
Optical Digital Inputs: Connect the optical digital output from a
DVD player, HDTV receiver, the output of a compatible computer sound
card playing MP3 files or streams, LD player, MD player or CD player to
these jacks.The signal may be either a Dolby Digital signal, a DTS signal,
a 2 channel MPEG 1 signal, or a standard PCM digital source.
S
Analog 4 Audio Inputs: Connect these jacks to the PLAY/OUT
audio jacks on aTV or other audio or video source.
T
Video 2 Video Inputs: Connect these jacks to the PLAY/OUT
composite or S-Video jacks on a secondVCR or other video source.
U
Remote Input and Output: If the AVR’s front-panel IR sensor is
blocked due to cabinet doors or other obstructions, an external IR sensor
may be used. Connect the output of the sensor to the Remote IN jack.
The Output connection permits the IR sensor in the receiver to serve
other remote controlled devices. Connect this jack to the“IR IN”jack on
Harman Kardon or other compatible equipment.
V
Zone 2 IR Input: Connect the output of an IR sensor in a remote
room to this jack to operate the AVR’s multiroom control system.
W
Preamp Outputs: Connect these jacks to an optional, external
power amplifier for applications where higher power is desired.
X
HDMI Output: Connect this jack to the HDMI input on a compatible
HDMI-equipped video display.
Y
Video 3 Video Inputs: Connect these jacks to the PLAY/OUT
composite or S-Video jacks on any video source.
Z
Analog 3 Audio Inputs: Connect these jacks to the PLAY/OUT
audio jacks on any audio or video source.
a
HDMI Inputs: Connect the HDMI output of video sources such as a
DVD player, set-top box or HDTV tuner to either of these jacks.
b
Main Power Switch: Press this button ON to apply power to the
AVR. When the switch is ON, the unit is placed in a Standby mode, as
indicated by the amber LED
2 .This button MUST be ON to operate
the unit.To turn the unit off completely and prevent the use of the
remote control, this switch should be pressed OFF.
NOTE: This switch is
normally left in the“ON”position.
With the AVR’s powerful processor, you may connect up to three
HDMI-equipped source devices to the HDMI inputs using a single-cable
connection, while benefiting from superior digital audio and video
performance. However, if your video display is not HDMI-compatible, you
will need to connect the source device to one of the other source inputs,
selecting a coaxial or optical digital audio input and analog video input.
See the Connections and Installation sections for more information.
If your video display has an HDMI input, but some of your sources have only
analog video outputs, you may still rely on just the HDMI video connection
to your display; the AVR will automatically transcode analog video signals
to the HDMI format.
NOTE ON VIDEO CONNECTIONS: When connecting a video source
product such as aVCR, DVD player, satellite receiver, cable set-top box,
personal video recorder or video game to the AVR 260, you may use either a
composite or S-video connection, but not both.
harman/kardon
AVR 260/230 Service Manual
Page 7 of 131

11
ENGLISH
REMOTE CONTROL FUNCTIONS
AVR Power On A
AVR Power Off B
Source C Selectors
Audio Effects Button
D
Transport Controls E
Menu Navigation F LKM N
Sleep Button G
Main Tuning Buttons H
Last Button I
Numeric Keys J
Video Mode Button K
Menu Button L
Activity Button M
Back/Exit Button N
Master Volume O
Disc Menu Button P
Mute Button Q
Surround Mode Button R
Device Power OFF Button S
Device Power ON Button T
Transmitter Window U
OK Button V
Settings W Buttons
Zone Select Button
X
Red/Green/Yellow/Blue Color Buttons Y
Note :The function names shown here are each button’s feature when
used with the AVR. Most buttons have additional functions when used with
other devices. See page 46 for a list of these functions.
harman/kardon
AVR 260/230 Service Manual
Page 8 of 131

12
REMOTE CONTROL FUNCTIONS
The remote is capable of operating the AVR 260 and most Harman Kardon CD
changers or players, CD Recorders and Blu-ray players, using the control codes
that are part of the remote.
AVR Power On: A When the AVR 260 is in the Standby mode, as
indicated by the Power Indicator
2 glowing amber, press this button to
turn the unit on.
AVR Power Off: B When the AVR 260 is turned on, press this button to
place it in the Standby mode. Note that in this condition, the unit is still
connected to AC Power.
Source Selectors: C Press these buttons to select an input source for
the AVR 260.
Audio Effects Button: D Press this button to go directly to the Audio
Effects Menu.
Transport Controls: E These buttons are used to control Play, Play
Forward, Play Reverse, Stop, Pause and Record functions on compatible
Harman Kardon compact disc players/changers and cassette tape decks.
Menu Navigation Buttons: F Use these buttons to move Up, Down,
Left or Right when using the Menu system of the AVR 260.
Sleep Button: G Press this button to place the unit in the Sleep mode.
Each press of the button selects the amount of time that will remain
before the unit will automatically go into the Standby mode, as shown
in the Main Information Display
C , in the following order:
Holding the button pressed for some seconds will directly turn off the
Sleep time selection.
Channel/Page Button: H When the tuner has been selected,
this control selects a preset radio station. Press these buttons while
operating a cable, satellite or HDTV set-top box or a television to change
channels.The Page control may be available with some DVD players
when playing a DVD Audio disc containing pages of images associated
with a track.
Last Button: I When the tuner is in use, pressing this button returns
to the last station tuned. When controlling a cable, satellite or HDTV
set-top box or aTV, press this button to return to the previous television
channel.
Numeric Keys: J These buttons serve as a ten-button numeric keypad
to enter tuner preset positions or track numbers with CD players/
changers or to tune stations directly.
Video Modes Button: K Press this button to go directly to theVideo
Modes Menu.
Menu Button: L When using a H/K DVD player with the receiver, you
can activate the DVD Menu with this button.
Activity Button: M This button may be programmed to transmit a
series of commands with a single press, which is useful for powering
on all devices and selecting the correct settings on each device, or for
selecting multi-digit channels with a single press. See the section on
Programming the Remote for more information on Activities.
Press this button to enter the Activity programming function, or before
pressing one of the Buttons that you have programmed with an Activity
sequence, to begin transmitting the entire sequence.
Back/Exit Button: N Press this button to go back to the previous Menu
or to exit a Menu.
Master Volume: O Press these buttons to raise or lower the AVR 260’s
volume.
Disc Menu: P Press this button to open the menu of a DVD disc that you
are watching.
Mute Button: Q Press this button to momentarily silence the AVR 260.
Surround Modes Button: R Press this button to enter the Surround
Modes selection Menu.
Device Power Off: S Turns Off the power of other devices that you
have selected to control with the Source Selector Buttons
C .
Device Power On: T Turns On the power of other devices that you
have selected to control with the Source Selector Buttons
C .
Transmitter Window: U Point this area of the remote toward the
receiver when using the remote.
OK Button: V This button confirms settings and orders in the menus.
Settings Buttons: W Open the AVR, INFO or SOURCE settings with one
press of one of these buttons.
Zone Select: X This button slides sideways to switch the remote control
between controlling Zone 1 or Zone 2 of the AVR.
Color Buttons: Y These four buttons are used as color buttons when
controlling aTV set.They have various functions when controlling other
devices. Please refer to the remote control CodeTables page 46.
harman/kardon
AVR 260/230 Service Manual
Page 9 of 131

48
TROUBLEShOOTINg gUIDE
SYMPTOM CAUSE SOLUTION
Unit does not function when Main
Power Switch
0 is pushed
No AC Power•Make certain AC power cord is plugged into a live outlet•
Check to see if outlet is switch controlled•
Display lights, but no sound or
picture
Intermittent input connections•
Mute is on•
Volume control is down•
Make certain that all input and speaker connections are secure•
Press Mute button•
Q
Turn up volume control•
No sound from any speaker;
ProtectWarning in Display
Amplifier is in protection mode due to•
possible short
Amplifier is in protection mode due to•
internal problems
Check speaker-wire connections for shorts at receiver and speaker•
ends
Contact your local Harman Kardon service depot•
No sound from surround or center
speakers
Incorrect surround mode•
Input is mono•
Incorrect configuration•
Stereo or Mono program material•
Select a mode other than Stereo•
There is no surround information from mono sources (except with•
Theater and Hall surround modes)
Check speaker mode configuration•
Some surround modes may not create rear-channel information from•
nonencoded programs
Unit does not respond to remote
commands
Weak batteries in remote•
Wrong device selected•
Remote sensor•
N is obscured
Change remote batteries•
Press the AVR Selector•
W
Make certain front-panel sensor is visible to remote or connect•
remote sensor
Intermittent buzzing in tuner Local interference•Move unit or antenna away from computers, fluorescent lights,•
motors or other electrical appliances
Letters flash in the Channel
Indicator Display
D and Digital
Audio stops
Digital audio feed paused•Resume play for DVD•/Blu-ray
Check that Digital Signal is fed to the Digital Input selected•
No picture or on-screen
information on theTV screen
AVR Resolution to Display is not correct, too•
high or too low.
Select correct Resolution as described on•page 19 "Resolution To
Display"
Processor Reset
In the rare case where the unit’s operation or the displays seem abnormal,
the cause may involve the erratic operation of the system’s memory or
microprocessor.
To correct this problem, first unplug the unit from the AC wall outlet and wait
at least three minutes. After the pause, reconnect the AC power cord and
check the unit’s operation. If the system still malfunctions, a system reset may
clear the problem.
To clear the AVR’s entire system memory including tuner presets, output
level settings, delay times and speaker configuration data, first put the unit
in Standby by pressing the System Power Control button
1 . Next press and
hold the OK button
5 for five seconds.
The unit will turn on automatically and show the word RESET in the Display
for a few seconds.Then it reverts to normal ON status. Note that once you
have cleared the memory in this manner, it is necessary to re-establish all
system configuration settings and tuner presets.
NOTE : Resetting the processor will erase any configuration settings you have
made for speakers, output levels, surround modes, digital input assignments
as well as the tuner presets. After a reset the unit will be returned to the
factory presets, and all settings for these items must be reentered.
If the system is still operating incorrectly, there may have been an electronic
discharge or severe AC line interference that has corrupted the memory or
microprocessor.
If these steps do not solve the problem, consult an authorized Harman Kardon
service depot.
harman/kardon
AVR 260/230 Service Manual
Page 10 of 131

49
ENGLISH
TEChNICAL SPECIFICATIONS
Audio Section
Stereo Mode, Continuous Average Power (FTC)
65Watts per channel, 20Hz–20kHz,
@ <0.07%THD, both channels driven into 8 ohms
Seven-Channel Surround Modes
Power Per Individual Channel, with all channels driven
Front L & R channels:
50Watts per channel
@ <0.07%THD, 20Hz–20kHz into 8 ohms
Center channel:
50 Watts
@ <0.07%THD, 20Hz–20kHz into 8 ohms
Surround (L & R Side, L & R Back) channels:
50Watts per channel
@ <0.07%THD, 20Hz–20kHz into 8 ohms
120Watts per channel into 6 ohms
@1kHz, <1% THD, one channel driven.
Input Sensitivity/Impedance
Linear (High-Level) 200mV/47k ohms
Signal-to-Noise Ratio (IHF-A) 100dB
Surround System Adjacent Channel Separation
Analog Decoding
(Pro Logic® etc.) 40dB
Dolby® Digital (AC-3) 55dB
DTS® 55dB
Frequency Response
@ 1W (+0dB, –3dB) 10Hz –130kHz
High Instantaneous
Current Capability (HCC) ±35 Amps
Transient Intermodulation
Distortion (TIM) Unmeasurable
Rise Time 16 µsec
Slew Rate 40V/µsec**
FM Tuner Section
Frequency Range 87.5–108.0MHz
Usable Sensitivity IHF 1.3µV/13.2dBf
Signal-to-Noise Ratio Mono/Stereo 70/68dB (DIN)
Distortion Mono/Stereo 0.2/0.3%
Stereo Separation 40dB @ 1kHz
Selectivity ±400kHz, 70dB
Image Rejection 80dB
IF Rejection 90dB
AM Tuner Section
Frequency Range 522–1620kHz
Signal-to-Noise Ratio 45dB
Usable Sensitivity Loop 500µV
Distortion 1kHz, 50% Mod 0.8%
Selectivity ±10kHz, 30dB
Video Section
Video Format PAL/NTSC
Input Level/Impedance 1Vp-p/75 ohms
Output Level/Impedance 1Vp-p/75 ohms
Video Frequency Response
(Composite and S-Video) 10Hz–8MHz (–3dB)
Video Frequency Response
(ComponentVideo) 10Hz–100MHz (–3dB)
HDMI™ Version 1.3a
General
Power Requirement AC 220-230V 50/60Hz
Power Consumption Standby < 1W,
540W maximum
(7 channels driven)
Dimensions (Max)
Width 440mm
Height 165mm
Depth 382mm
Weight 14,0 kg
Depth measurement includes knobs, buttons and terminal connections.
Height measurement includes feet and chassis.
Features, specifications and appearance are subject to change without notice.
This product incorporates copyright protection technology that is protected by
method claims of certain U.S. patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
Harman Kardon and Logic 7 are trademarks of Harman International Industries,
Incorporated, registered in the United States and/or other countries. EzSet/EQ, Designed
to Entertain andThe Bridge II logo are trademarks of Harman International Industries,
Incorporated.
*Manufactured under license from Dolby Laboratories.
"DolbyTrue HD", "Dolby Digital Plus",“Dolby,”“Pro Logic”and the Double-D symbol are
trademarks of Dolby Laboratories.
"DTS-HD Master Audio", "DTS-HD", "DTS","DTS ES","Neo:6"and"96/24" are trademarks of
DTS,Inc.
SA-CD is a trademark of Sony Electronics, Inc.
Blu-ray Disc is a trademark of the Blu-ray Disc Association.
Apple and iPod are registered trademarks of Apple Computer, Inc.
Cirrus is a registered trademark of Cirrus Logic Corp.
**Without input anti slewing and output isolation networks.
Faroudja and DCDi by Faroudja are trademarks of Genesis Microchip, Inc.
HD-DVD is a trademark of the DVD Format/Logo Licensing Corporation (DVD FLLC).
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing, LLC.
harman/kardon
AVR 260/230 Service Manual
Page 11 of 131

harman/kardon
AVR 260/230 Service Manual
Page 12 of 131

harman/kardon
AVR 260/230 Service Manual
Page 13 of 131

harman/kardon
AVR 260/230 Service Manual
Page 14 of 131

Leve
l
Ref. # Part Numbe
r
Description Drawin
g
No
(
Value
)
Qt
y
0,2 CGB1A218Z BADGE , AVR260 1
0,2 CGL1A222 INDICATOR , VOLUME AVR130/230/330 1
0,2 CGR3A436 COVER , JACK A 1
0,2 CGR3A437 COVER , JACK B 1
0,2 CGU1A318Y ORNAMENT , VOLUME AVR255 1
0,2 CGU1A410A25W WINDOW , FIP 1
0,2 CGX1A338MBC63 CAP , VOLUME 1
0,2 CGX1A391C66 ORNAMENT , AL A AVR350 1
0,2 CGX1A392C66 ORNAMENT , AL B AVR350 1
0,2 CGX2A390C66X SHEET , AL FRONT AVR255/230 1
0,2 CKC6B145S60 CABINET , TOP AVR350 1
0,2 CMH1A214 HOLDER , VOLUME AVR130/230/330 1
0,2 CMZ1A127 FILTER , FIP AVR255 1
0,2 CMZ2A090 SHEET , VOLUME 1
0,2 CQB1A549Y LABEL , ATTENTION DVD48 1
0,2 CQB1A622 LABEL , SERIAL NO 1
0,2 CTB3+8JFZR SCREW 15
0,2 CTB4+6FFZR SCREW 6
0,2 C4B120122 TUBE , UL 0,1
1 CARTAVR260E-HK REMOCON ASS'Y (57KEY) AVR260 1
1 CHE154 CLAMPER , ARM 0,1
1 CJXAVR340MICRO MICRO PHONE ASS'Y 1
1 CPG1A891V BOX , OUT CARTON 1
1 CPS5A564Z PAD , SNOW L AVR155 1
1 CPS5A565Z PAD , SNOW R AVR155 1
1 CQB1A907Z LABEL , BAR CODE AVR154 1
1 CQB1A928Z LABEL , MADE IN PRC 2
1 CQS1A001 RIBON , BAR CODE SONY(TR-4070) 0,1
1 CQXAVR260/240 INSTRUCTION MANUAL ASS'Y 1
0,2 CQB1A971 LABEL , BAR CODE(MANUAL) 1
0,2 CQE1A220Z SHEET , FRONT COVER AVR130/230BK 1
0,2 CQE1A411Z SHEET , BATTERY HARMAN 1
0,2 CQX1A1318W MANUAL , INSTRUCTION 1
0,2 CQX1A1320X MANUAL , SETUP 1
0,2 CSA1A018Z FM 1 POLE ANT 1
0,2 CSA1A020Z ANT , AM LOOP 1
1 CRE1A037 LOCKER SH08M790BO 14
Leve
l
Ref. # Part Numbe
r
Description Drawin
g
No
(
Value
)
Qt
y
0,2 CGWAVR260/240 FRONT PANEL ASS'Y 1
..3 CBT2A1064 KNOB , STANDBY 1
..3 CBT2A1065 KNOB , BACK 1
..3 CGB1A158Y BADGE , FRONT HARMAN/KARDON 1
..3 CGL1A265Y INDICATOR , POWER AVR155 1
..3 CGW2A447RHTB24 PANEL , FRONT 1
..3 CHG1A309 RUBBER 1
..3 CHR301 CLAMPER 32
..3 CHS1A032 TAPE , HEMELON 1
..3 CHS1A165 TAPE , HEMELON 1
..3 CMC2A323 PLATE , SHIELD 1
..3 CMC2A326 PLATE , EARTH AVR350 1
..3 CMC2A338 PLATE , EARTH AVR350 2
..3 CMD1A555 BRACKET , SIDE (L) 1
..3 CMD2A443 BRACKET , SIDE 1
..3 CMH2A215 HOLDER , LED AVR350 1
..3 CPE1A009 SHEET , BLIND 1
..3 CTB3+10JR SCREW 30
..3 CTWS3+10GR SCREW 1
..3 CB72 CWC4F2A17A280B CABLE , CARD(17P, 280mm) 1
Leve
l
Ref. # Part Numbe
r
Description Drawin
g
No
(
Value
)
Qt
y
0,2 CUAAVR260/240 BOTTOM CHASSIS ASS'Y 1
..3 CHD1A012ZR SCREW , SPECIAL 2
..3 CHD1A023R SCREW , SPECIAL 4
..3 CHD4A012R SCREW , SPECIAL 5
..3 CHE170 HOLDER , PCB 2
..3 CHE36-3 CLAMPER , WIRE 3
..3 CHG1A104Z CUSHUON , RUBBER 1
..3 CHG1A160Z CUSHION , RUBBER 1
..3 CHG1A373 CUSHION , FOOT AVR350 4
..3 CHS1A032 TAPE , HEMELON 4
..3 CJA2B044ZA CORD , POWER (KENIC) EUR 16A 250V 1
BOTTOM CHASSIS ASS'Y
FRONT PANEL ASSY
AVR260/230 Electrical & Mechanical Parts List
harman/kardon
AVR 260/230 Service Manual
Page 15 of 131

Leve
l
Ref. # Part Numbe
r
Description Drawin
g
No
(
Value
)
Qt
y
..3 CKF7A337W PANEL , REAR 1
..3 CKL1A094 FOOT , A AVR350 2
..3 CKL1A095 FOOT , B AVR350 2
..3 CLZ9W003Z FERRITE , RING 29X7.7X19 1
..3 CMD1A636 BRACKET , PCB 1
..3 CMD3A487 BRACKET , TRANS 1
..3 CNVM9014MS1J75L MODULE , TUNER EUR KST-M9014MS1-J75L(W/19KHZ) 1
..3 CTB3+10JFZR SCREW 26
..3 CTB3+6FFZR SCREW 12
..3 CTB3+6JR SCREW 15
..3 CTB3+8JR SCREW 11
..3 CTS3+8JFZR SCREW 4
..3 CTW3+12JR SCREW 2
..3 CTW3+8JR SCREW 6
..3 CUA1A282 CHASSIS , BOTTOM AVR255 1
..3 C2K86162 SOLDER
,
FLUX WIRE PB FREE(PIE 1.6 HSE-04 W1.6 5,5
..3 KHR1A028 BUSHING , AC CORD 1
..3 BN90 CSHAVR155ZA MOMS SW ASS'Y 1
...4 CSH1A009ZV SWITCH , MOMS 1
...4 CWZAVR255ZA WIRE , ASS'Y(2P,150mm) 1
..3 CB11 CWC4F2A17A100B CABLE , CARD(17P, 100MM, 1MM, B-TYPE) 1
..3 CB12 CWC4C4A21B120B10 CABLE , CARD (21P,1.25MM,250MM,B,10MM) 1
..3 CB13 CWC4C4A13B100B CABLE , CARD AVR-5048 1
..3 CB14 CWC4F2A13A100B CABLE , CARD(13P, 100mm) 1
..3 CB15 CWC4F2A17A120B CABLE , CARD(17P, 120mm) 1
..3 CB19 CWC4F2A07A080B CABLE , CARD(7P, 80mm, B TYPE) 1
..3 CB47 CWC4F2A07A100B CABLE , CARD(7P, 1MM, 100MM) 1
..3 F901 KBA2C6300TLEZ FUSE 6.3A 1
..3 T901 CLT5W032ZE TRANS , POWER AVR255/230 1
Leve
l
Ref. # Part Numbe
r
Description Drawin
g
No
(
Value
)
Qt
y
..3 COP12053I AVR255/230 FRONT PCB ASS'Y 1
....5 C714 CCBS1H151KBT CAP , CERAMIC(150PF/50V) CH UP025 B151K-A-B Z 1
....5 C716 CCEA1AH331T CAP , ELECT 330UF 10V 1
....5 C719 CCBS1H102KBT CAP , CERAMIC(1000PF/50V) CH UP025 B102K-A-B Z 1
....5 C720 CCBS1H102KBT CAP , CERAMIC(1000PF/50V) CH UP025 B102K-A-B Z 1
....5 C721 CCBS1H102KBT CAP , CERAMIC(1000PF/50V) CH UP025 B102K-A-B Z 1
....5 C723 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1
....5 C728 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1
....5 C729 CCBS1H473ZFT CAP , CERAMIC(47000PF/50V) CH UP025 F473Z-A-B J 1
....5 C735 CCEA1CKS100T CAP , ELECT 10UF 16V 1
....5 C742 CCBS1H223ZFT CAP , CERAMIC(22000PF/50V) CH UP025 F223Z-A-B J 1
....5 C793 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1
....5 C794 CCBS1C222MXT CAP , CERAMIC(2200PF/16V) CH EP025 B222M-A-B J 1
....5 C795 CCBS1H102KBT CAP , CERAMIC(1000PF/50V) CH UP025 B102K-A-B Z 1
....5 C796 CCBS1H102KBT CAP , CERAMIC(1000PF/50V) CH UP025 B102K-A-B Z 1
....5 C805 CCBS1H223ZFT CAP , CERAMIC(22000PF/50V) CH UP025 F223Z-A-B J 1
....5 C806 CCBS1H223ZFT CAP , CERAMIC(22000PF/50V) CH UP025 F223Z-A-B J 1
....5 C807 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1
....5 C808 CCBS1H181KBT CAP , CERAMIC(180PF/50V) CH UP025 B181K-A-B Z 1
....5 C809 CCEA1AH471T CAP , ELECT 470UF 10V 1
....5 C812 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1
....5 C817 CCBS1H100JCT CAP , CERAMIC(10PF/50V) CH UP025CH100J-A-B Z1
....5 C820 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C821 CCEA1EH470T CAP , ELECT 47UF 25V 1
....5 C822 CCEA1EH470T CAP , ELECT 47UF 25V 1
....5 C823 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C824 CCBS1H471KBT CAP , CERAMIC(470PF/50V) CH UP025 B471K-A-B Z 1
....5 C825 CCBS1H151KBT CAP , CERAMIC(150PF/50V) CH UP025 B151K-A-B Z 1
....5 C828 CCBS1H470JT CAP , CERAMIC(47PF/50V) CH UP025SL470J-A-B Z 1
....5 C830 CCBS1H473ZFT CAP , CERAMIC(47000PF/50V) CH UP025 F473Z-A-B J 1
....5 C841 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C842 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C843 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C850 CCBS1H471KBT CAP , CERAMIC(470PF/50V) CH UP025 B471K-A-B Z 1
....5 C851 CCBS1H471KBT CAP , CERAMIC(470PF/50V) CH UP025 B471K-A-B Z 1
....5 C852 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1
....5 C855 CCBS1H101KBT CAP , CERAMIC(100PF/50V) CH UP025 B101K-A-B Z 1
....5 C856 CCBS1H101KBT CAP , CERAMIC(100PF/50V) CH UP025 B101K-A-B Z 1
....5 C857 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1
....5 C862 CCBS1H101KBT CAP , CERAMIC(100PF/50V) CH UP025 B101K-A-B Z 1
....5 C863 CCBS1H101KBT CAP , CERAMIC(100PF/50V) CH UP025 B101K-A-B Z 1
....5 C866 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C867 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C868 CCEA1EH470T CAP , ELECT 47UF 25V 1
FRONT PCB ASSY
BOTTOM CHASSIS ASS'Y
harman/kardon
AVR 260/230 Service Manual
Page 16 of 131

Leve
l
Ref. # Part Numbe
r
Description Drawin
g
No
(
Value
)
Qt
y
....5 C869 CCEA1EH470T CAP , ELECT 47UF 25V 1
....5 C870 CCBS1H681KBT CAP , CERAMIC(680PF/50V) CH UP025 B681K-A-B Z 1
....5 C871 CCBS1H681KBT CAP , CERAMIC(680PF/50V) CH UP025 B681K-A-B Z 1
....5 C872 CCEA1CH331T CAP , ELECT 330UF 16V 1
....5 C873 CCEA1CH331T CAP , ELECT 330UF 16V 1
....5 C874 CCBS1H101KBT CAP , CERAMIC(100PF/50V) CH UP025 B101K-A-B Z 1
....5 C882 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1
....5 C888 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1
....5 C889 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1
....5 C891 CCBS1H223ZFT CAP , CERAMIC(22000PF/50V) CH UP025 F223Z-A-B J 1
....5 C892 CCBS1H223ZFT CAP , CERAMIC(22000PF/50V) CH UP025 F223Z-A-B J 1
....5 C893 CCBS1H223ZFT CAP , CERAMIC(22000PF/50V) CH UP025 F223Z-A-B J 1
....5 C894 CCEA1CKS100T CAP , ELECT 10UF 16V 1
....5 C896 CCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z 1
....5 C897 CCEA1AH471T CAP , ELECT 470UF 10V 1
....5 C903 CCEA1HKS2R2T CAP , ELECT 2.2UF 50V SMALL SIZE 1
....5 C905 CCEA1HKS2R2T CAP , ELECT 2.2UF 50V SMALL SIZE 1
....5 D455 CVD1SS133MT DIODE 1SS133 1
....5 D774 CVD1SS133MT DIODE 1SS133 1
....5 D775 CVD1SS133MT DIODE 1SS133 1
....5 D784 CVD1SS133MT DIODE 1SS133 1
....5 D785 CVD1SS133MT DIODE 1SS133 1
....5 L702 HLQ02C100KT COIL , AXAIL (10UH) 1
....5 Q451 HVTKRC107MT T.R KRC107M 1
....5 Q452 HVTKRA107MT T.R KRA107M 1
....5 Q454 HVTKRC107MT T.R KRC107M 1
....5 Q701 HVTKRC107MT T.R KRC107M 1
....5 Q722 HVTKRA107MT T.R KRA107M 1
....5 Q724 HVTKRC107MT T.R KRC107M 1
....5 Q725 HVTKRC107MT T.R KRC107M 1
....5 Q734 HVTKTC2874BT T.R , MUTE KTC2874B 1
....5 Q735 HVTKTC2874BT T.R , MUTE KTC2874B 1
....5 Q736 HVTKTC2874BT T.R , MUTE KTC2874B 1
....5 Q737 HVTKTC2874BT T.R , MUTE KTC2874B 1
....5 Q738 HVTKRC107MT T.R KRC107M 1
....5 Q739 HVTKTA1271YT T.R KTA1271Y 1
....5 Q740 HVTKTC3200GRT T.R KTC3200GR 1
....5 R452 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1
....5 R453 CRD20TJ362T RES , CARBON 3.6K OHM 1/5W J 1
....5 R454 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1
....5 R701 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1
....5 R704 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1
....5 R705 CRD20TJ101T RES , CARBON(1/5W,100,5%) 100 OHM 1/5W J 1
....5 R706 CRD20TJ101T RES , CARBON(1/5W,100,5%) 100 OHM 1/5W J 1
....5 R708 CRD20TJ101T RES , CARBON(1/5W,100,5%) 100 OHM 1/5W J 1
....5 R709 CRD20TJ470T RES , CARBON 47 OHM 1/5W J 1
....5 R710 CRD20TJ470T RES , CARBON 47 OHM 1/5W J 1
....5 R711 CRD20TJ470T RES , CARBON 47 OHM 1/5W J 1
....5 R718 CRD20TJ222T RES , CARBON 2.2K OHM 1/5W J 1
....5 R721 CRD20TJ101T RES , CARBON(1/5W,100,5%) 100 OHM 1/5W J 1
....5 R722 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1
....5 R723 CRD20TJ393T RES , CARBON (39K OHM) 1
....5 R724 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1
....5 R725 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1
....5 R727 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1
....5 R737 CRD20TJ100T RES , CARBON 10 OHM 1/5W J 1
....5 R747 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1
....5 R753 CRD20TF1001T RES , CARBON 1K /1/5W /F 1
....5 R754 CRD20TF1501T RES , CARBON 1.5K /1/5W /F 1
....5 R755 CRD20TF1801T RES , CARBON 1.8K /1/5W /F 1
....5 R756 CRD20TF2701T RES , CARBON 2.7K /1/5W/F 1
....5 R757 CRD20TF3301T RES , CARBON 3.3K /1/5W/F 1
....5 R758 CRD20TF5601T RES , CARBON(5.6K/F) 1
....5 R759 CRD20TF1001T RES , CARBON 1K /1/5W /F 1
....5 R760 CRD20TF1501T RES , CARBON 1.5K /1/5W /F 1
....5 R761 CRD20TF1801T RES , CARBON 1.8K /1/5W /F 1
....5 R762 CRD20TF2701T RES , CARBON 2.7K /1/5W/F 1
....5 R763 CRD20TF3301T RES , CARBON 3.3K /1/5W/F 1
....5 R764 CRD20TF5601T RES , CARBON(5.6K/F) 1
....5 R765 CRD20TF7501T RES , CARBON (7.5K/F) 1
....5 R781 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1
....5 R782 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1
....5 R783 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1
....5 R784 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1
....5 R786 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1
....5 R787 CRD20TJ101T RES , CARBON(1/5W,100,5%) 100 OHM 1/5W J 1
....5 R791 CRD20TJ123T RES , CARBON 12K OHM 1/5W J 1
FRONT PCB ASSY
harman/kardon
AVR 260/230 Service Manual
Page 17 of 131

Leve
l
Ref. # Part Numbe
r
Description Drawin
g
No
(
Value
)
Qt
y
....5 R805 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1
....5 R806 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1
....5 R824 CRD20TF2200T RES , CARBON(220 OHM, 1%) 1
....5 R825 CRD20TF6800T RES , CARBON(680 OHM, 1%) 1
....5 R864 CRD20TJ272T RES , CARBON 2.7K OHM 1/5W J 1
....5 R865 CRD20TJ101T RES , CARBON(1/5W,100,5%) 100 OHM 1/5W J 1
....5 R866 CRD20TJ272T RES , CARBON 2.7K OHM 1/5W J 1
....5 R869 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1
....5 R871 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1
....5 R872 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1
....5 R873 CRD20TJ471T RES , CARBON 470 OHM 1/5W J 1
....5 R874 CRD20TJ471T RES , CARBON 470 OHM 1/5W J 1
....5 R875 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1
....5 R876 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1
....5 R877 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1
....5 R878 CRD20TJ750T RES , CARBON 75 OHM 1/5W J 1
....5 R892 CRD20TJ222T RES , CARBON 2.2K OHM 1/5W J 1
....5 R893 CRD20TJ333T RES , CARBON 33K OHM 1/5W J 1
....5 R895 CRD20TJ101T RES , CARBON(1/5W,100,5%) 100 OHM 1/5W J 1
....5 R896 CRD20TJ101T RES , CARBON(1/5W,100,5%) 100 OHM 1/5W J 1
....5 R897 CRD20TJ101T RES , CARBON(1/5W,100,5%) 100 OHM 1/5W J 1
....5 R898 CRD20TJ101T RES , CARBON(1/5W,100,5%) 100 OHM 1/5W J 1
....5 R899 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1
....5 R900 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1
....5 R901 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1
....5 R902 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J 1
....5 R903 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1
....5 R904 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1
....5 R905 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1
....5 R906 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1
....5 R907 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1
....5 R908 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1
....5 R909 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1
....5 R910 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1
....5 R911 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1
....5 R912 CRD20TJ221T RES , CARBON 220 OHM 1/5W J 1
....5 R913 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1
....5 R915 CRD20TJ473T RES , CARBON 47K OHM 1/5W J 1
....5 R918 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1
....5 R919 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J 1
....5 R920 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1
....5 R921 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1
....5 R922 CRD20TJ102T RES , CARBON 1K OHM 1/5W J 1
....5 R923 CRD20TJ101T RES , CARBON(1/5W,100,5%) 100 OHM 1/5W J 1
....5 R924 CRD20TJ101T RES , CARBON(1/5W,100,5%) 100 OHM 1/5W J 1
....5 R926 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1
....5 R934 CRD20TJ222T RES , CARBON 2.2K OHM 1/5W J 1
....5 R935 CRD20TJ103T RES , CARBON 10K OHM 1/5W J 1
....5 R936 CRD20TJ222T RES , CARBON 2.2K OHM 1/5W J 1
....5 R937 CRD20TJ104T RES , CARBON 100K OHM 1/5W J 1
....5 S701 CST1A024ZT SW , TACT 1
....5 S702 CST1A024ZT SW , TACT 1
....5 S703 CST1A024ZT SW , TACT 1
....5 S704 CST1A024ZT SW , TACT 1
....5 S705 CST1A024ZT SW , TACT 1
....5 S706 CST1A024ZT SW , TACT 1
....5 S707 CST1A024ZT SW , TACT 1
....5 S708 CST1A024ZT SW , TACT 1
....5 S709 CST1A024ZT SW , TACT 1
....5 S711 CST1A024ZT SW , TACT 1
....5 S712 CST1A024ZT SW , TACT 1
....5 S713 CST1A024ZT SW , TACT 1
....5 S714 CST1A024ZT SW , TACT 1
....5 S715 CST1A024ZT SW , TACT 1
...4 CMC2A325 PLATE , EARTH AVR155 1
...4 CQB1D022 A-ROHS/LABEL,SERIAL 1
...4 C4FM073 TAPE , BOTH SIDE 3M #4920 0,1
...4 BK71 CMD1A209 BRACKET , FLT A4-92-1739 1
...4 BK72 CMD1A209 BRACKET , FLT A4-92-1739 1
...4 BN10 CWZAVR155BN10 SHIELD WIRE ASS'Y(5P, 2MM, 350MM) 1
...4 BN18 CWZAVR355BN18A 5P FERRITE CORE WIRE ASS'Y (500MM, 2 CORE)1
....5 CLZ9Z028Z FERRITE , CORE(21.2X6.4X12.7) K5C T 2
....5 CWZAVR355BN18Z 5P SHIELD WIRE ASS'Y (500mm) 1
...4 BN22 CWZAVR155BN22A 7P FERRITE CORE WIRE ASS'Y(500MM, 2MM, 1 CORE) 1
....5 CLZ9Z028Z FERRITE , CORE(21.2X6.4X12.7) K5C T 1
....5 CWZAVR155BN22Z 7P WIRE ASS'Y (2mm,500mm) 1
...4 BN41 CWZAVR155BN41A 7P FERRITE CORE WIRE ASS'Y(500MM, 2MM, 1 CORE) 1
FRONT PCB ASSY
harman/kardon
AVR 260/230 Service Manual
Page 18 of 131

Leve
l
Ref. # Part Numbe
r
Description Drawin
g
No
(
Value
)
Qt
y
....5 CLZ9Z028Z FERRITE , CORE(21.2X6.4X12.7) K5C T 1
....5 CWZAVR155BN41ZA 7P WIRE ASS'Y 1Core 3turn (2mm,500mm) 1
...4 BN81 CWB1C907200BM WIRE ASS'Y 1
...4 BN84 CWB2B905080EN WIRE ASS'Y 1
...4 BN85 CWB2B903100EN WIRE ASS'Y 1
...4 BN88 CWB2B905050EN WIRE ASS'Y 1
...4 BN92 CWB2B905100EN WIRE ASS'Y 1
...4 CN72 CJP17GA117ZY WAFER 1
...4 CN84 CJP05GB46ZY WAFER 1
...4 CN85 CJP03GA19ZY WAFER , STRAIGHT(3PIN) 1
...4 CN88 CJP05GA19ZY WAFER , STRAIGHT 1
...4 CN92 CJP05GA19ZY WAFER , STRAIGHT 1
...4 D701 CVD1L0345W31BOCT201
W
L.E.D , WHITE 1
...4 D703 CVD1L0345W31BOCT201
W
L.E.D , WHITE 1
...4 D705 CVD1L0345W31BOCT201
W
L.E.D , WHITE 1
...4 D723 CVD30ASOGCAA-S7 L.E.D , ORANGE T0L-30ASOGCAA-S7 1
...4 D727 CVD1L0345W31BOCT201
W
L.E.D , WHITE 1
...4 D778 HVD1N5819T DIODE , SCHOTTKY 1N5819 1
...4 ET03 CMD1A629 BRACKET , PCB 1
...4 FIP1 CFL17BT031GINAK FIP , AVR355(17BT31GINAK) 1
...4 IC73 HRVNJL34H380A SENSOR , REMOCON (JRC) 1
...4 IC75 HVI74ACT04MTR I.C , HEX (ST) 1
...4 IC76 HVI74HCU04AFNG I.C , INVERTER (TOSHIBA) TC74HCU04AFNG(TOSHIBA) 1
...4 IC86 HVINJM4556AL I.C , HEADPHONE (JRC) NJM4556AL 1
...4 IC87 HVINJM2068MTE1 I.C , OP AMP (JRC) NJM2068M-TE1 1
...4 JK81 CJJ4M041Y JACK , BOARD (COAX) 1
...4 JK82 HJSTORX177L MODULE , OPTICAL(RX) TORX177L 1
...4 JK83 CJJ2E026Z JACK , HEADPHONE(SILVER PLATE) 1
...4 JK85 CJJ9M004Y JACK , S-VHS (SILVER) 1
...4 JK86 CJJ4S028Y JACK , BOARD (3P SILVER) 1
...4 JW83 CWE8202150RV WIRE ASS'Y 1
...4 JW84 CWE8202150RV WIRE ASS'Y 1
...4 JW88 CWE8202150RV WIRE ASS'Y 1
...4 RL45 CSL4A016ZU RELAY , 12V 2C2P BC3-12H 1
...4 VR74 CSR2A037Z ENCODER 1
Leve
l
Ref. # Part Numbe
r
Description Drawin
g
No
(
Value
)
Qt
y
..3 COP12026I AVR255/230 MAIN PCB ASS'Y 1
...4 CHD3A012R SCREW , SPECIAL 5
....5 C501 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C502 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C503 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C504 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C505 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C506 CCKT1H331KB CAP , CERAMIC 330PF 50V K 1
....5 C507 CCBS1H331KBT CAP , CERAMIC(330PF/50V) CH UP025 B331K-A-B Z 1
....5 C508 CCBS1H331KBT CAP , CERAMIC(330PF/50V) CH UP025 B331K-A-B Z 1
....5 C509 CCKT1H331KB CAP , CERAMIC 330PF 50V K 1
....5 C510 CCBS1H331KBT CAP , CERAMIC(330PF/50V) CH UP025 B331K-A-B Z 1
....5 C561 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C562 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C564 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C565 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C566 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C567 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C568 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C569 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C570 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C571 CCBS1H681KBT CAP , CERAMIC(680PF/50V) CH UP025 B681K-A-B Z 1
....5 C572 CCBS1H681KBT CAP , CERAMIC(680PF/50V) CH UP025 B681K-A-B Z 1
....5 C573 CCBS1H681KBT CAP , CERAMIC(680PF/50V) CH UP025 B681K-A-B Z 1
....5 C574 CCBS1H681KBT CAP , CERAMIC(680PF/50V) CH UP025 B681K-A-B Z 1
....5 C575 CCBS1H681KBT CAP , CERAMIC(680PF/50V) CH UP025 B681K-A-B Z 1
....5 C601 CCCT1H120JC CAP , CERAMIC 12PF 50V J 1
....5 C602 CCCT1H120JC CAP , CERAMIC 12PF 50V J 1
....5 C603 CCCT1H120JC CAP , CERAMIC 12PF 50V J 1
....5 C604 CCCT1H120JC CAP , CERAMIC 12PF 50V J 1
....5 C605 CCCT1H120JC CAP , CERAMIC 12PF 50V J 1
....5 C606 CCCT1H330JC CAP , CERAMIC 33PF 50V J 1
....5 C607 CCCT1H330JC CAP , CERAMIC 33PF 50V J 1
....5 C608 CCCT1H330JC CAP , CERAMIC 33PF 50V J 1
....5 C609 CCCT1H330JC CAP , CERAMIC 33PF 50V J 1
....5 C610 CCCT1H330JC CAP , CERAMIC 33PF 50V J 1
....5 C681 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C682 CCEA1HH100T CAP , ELECT 10UF 50V 1
MAIN PCB ASSY
FRONT PCB ASSY
harman/kardon
AVR 260/230 Service Manual
Page 19 of 131

Leve
l
Ref. # Part Numbe
r
Description Drawin
g
No
(
Value
)
Qt
y
....5 C683 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C684 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C685 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C721 CCKT1H221KB CAP , CERAMIC 220PF 50V K 1
....5 C722 CCKT1H221KB CAP , CERAMIC 220PF 50V K 1
....5 C723 CCKT1H221KB CAP , CERAMIC 220PF 50V K 1
....5 C724 CCKT1H221KB CAP , CERAMIC 220PF 50V K 1
....5 C725 CCKT1H221KB CAP , CERAMIC 220PF 50V K 1
....5 C726 CCKT1H221KB CAP , CERAMIC 220PF 50V K 1
....5 C727 CCKT1H221KB CAP , CERAMIC 220PF 50V K 1
....5 C728 CCKT1H221KB CAP , CERAMIC 220PF 50V K 1
....5 C801 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C802 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C803 CCCT1H330JC CAP , CERAMIC 33PF 50V J 1
....5 C804 CCCT1H330JC CAP , CERAMIC 33PF 50V J 1
....5 C805 CCCT1H120JC CAP , CERAMIC 12PF 50V J 1
....5 C806 CCCT1H120JC CAP , CERAMIC 12PF 50V J 1
....5 C811 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C812 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C813 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C814 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C815 CCKT1H331KB CAP , CERAMIC 330PF 50V K 1
....5 C816 CCBS1H331KBT CAP , CERAMIC(330PF/50V) CH UP025 B331K-A-B Z 1
....5 C817 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C818 CCEA1HH100T CAP , ELECT 10UF 50V 1
....5 C819 CCBS1H681KBT CAP , CERAMIC(680PF/50V) CH UP025 B681K-A-B Z 1
....5 C820 CCBS1H681KBT CAP , CERAMIC(680PF/50V) CH UP025 B681K-A-B Z 1
....5 C900 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J 1
....5 C901 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J 1
....5 C905 CCFT1H223ZF CAP , CERAMIC 0.022UF 50V Z 1
....5 C907 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C908 CCFT1H223ZF CAP , CERAMIC 0.022UF 50V Z 1
....5 C910 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J 1
....5 C911 CCEA1CH471T CAP , ELECT 470UF 16V 1
....5 C912 CCEA1EH221T CAP , ELECT 220UF 25V 1
....5 C913 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z 1
....5 C914 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J 1
....5 C917 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J 1
....5 C918 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J 1
....5 C919 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J 1
....5 C924 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z 1
....5 C925 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z 1
....5 C926 CCEA1CH221T CAP , ELECT 220UF 16V 1
....5 C932 CCEA1CH101T CAP , ELECT 100UF 16V 1
....5 C933 CCEA1CH221T CAP , ELECT 220UF 16V 1
....5 C934 CCFT1H223ZF CAP , CERAMIC 0.022UF 50V Z 1
....5 C939 CCEA1HH4R7T CAP , ELECT 4.7UF 50V 1
....5 C940 CCEA1AH471T CAP , ELECT 470UF 10V 1
....5 C948 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z 1
....5 C950 CCEA1AH471T CAP , ELECT 470UF 10V 1
....5 C971 HCQI1H562JZT CAP , MYLAR 5600PF 50V J 1
....5 C972 HCQI1H562JZT CAP , MYLAR 5600PF 50V J 1
....5 C973 HCQI1H562JZT CAP , MYLAR 5600PF 50V J 1
....5 C974 HCQI1H562JZT CAP , MYLAR 5600PF 50V J 1
....5 C975 HCQI1H562JZT CAP , MYLAR 5600PF 50V J 1
....5 C977 CCEA1HH3R3T CAP , ELECT 3.3UF 50V 1
....5 C980 HCQI1H562JZT CAP , MYLAR 5600PF 50V J 1
....5 C981 HCQI1H562JZT CAP , MYLAR 5600PF 50V J 1
....5 C990 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J 1
....5 C991 CCEA1HH1R0T CAP , ELECT 1UF 50V 1
....5 C992 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J 1
....5 C993 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J 1
....5 C994 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J 1
....5 C995 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J 1
....5 C996 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J 1
....5 C997 HCQI1H473JZT CAP , MYLAR 0.047UF 50V J 1
....5 C999 CCFT1H223ZF CAP , CERAMIC 0.022UF 50V Z 1
....5 D501 CVD1SS133MT DIODE 1SS133 1
....5 D502 CVD1SS133MT DIODE 1SS133 1
....5 D503 CVD1SS133MT DIODE 1SS133 1
....5 D504 CVD1SS133MT DIODE 1SS133 1
....5 D505 CVD1SS133MT DIODE 1SS133 1
....5 D581 CVD1SS133MT DIODE 1SS133 1
....5 D582 CVD1SS133MT DIODE 1SS133 1
....5 D583 CVD1SS133MT DIODE 1SS133 1
....5 D584 CVD1SS133MT DIODE 1SS133 1
....5 D585 CVD1SS133MT DIODE 1SS133 1
MAIN PCB ASSY
harman/kardon
AVR 260/230 Service Manual
Page 20 of 131