Harman Kardon AVR 630 User manual

Thank you for purchasing a Harman Kardon AVR 630.This Quick-Start
Guide will help you with a basic system installation. For detailed information
on any step, please refer to the Owner’s Manual pages referenced in this
guide.We strongly recommend that you read the Owner’s Manual for
complete details on how to install, configure and operate the AVR 630,
as well as for the important safety information it contains.
Figure 1 – Speaker Placement
The colors shown for each speaker correspond to
the matching output terminal connection on the
back of the AVR 630 (see page 8).
FRONT
LEFT
SPEAKER
(White)
SURROUND
BACK
LEFT
SPEAKER
(Brown)
SURROUND
BACK
RIGHT
SPEAKER
(Tan)
CENTER
SPEAKER
(Green)
SUBWOOFER
(Purple)
SURROUND
LEFT
SPEAKER
(Blue)
FRONT
RIGHT
SPEAKER
(Red)
SURROUND
RIGHT
SPEAKER
(Gray)
Step 1. Place your speakers in the listening room
(see page 19).
SPEAKER PLACEMENT
AVR 630 QUICK-START GUIDE
Connections Color Guide
Audio Connections Left Right
Front
Center
Surround
Subwoofer
Surround Back
Digital Audio Connections
Coaxial
Optical
Video Connections
Composite
S-Video
Match the colored jacks on the AVR 630 to the appropriate
jacks on your source equipment or speakers.The colors are
standardized, but not all equipment or connectors use them.

AVR 630 QUICK-START GUIDE
Step 2. Connect the speakers to the receiver: red (+) on speaker to colored (+) on receiver and black (–) to black (–)
(see page 16).
Step 3. Connect the Subwoofer Pre-Out jack to the Line-In jack on your subwoofer.
You may adjust the settings on the subwoofer later as needed (see page 16). Figure 3 – How to Use the Binding-Post
Speaker Terminal
SURROUND BACK
RIGHT SPEAKER
SURROUND BACK
LEFT SPEAKER
FRONT RIGHT
SPEAKER FRONT LEFT
SPEAKER CENTER SPEAKER
SUBWOOFER
+
_
+
_
LINE IN/SUB/LFE +
_
SURROUND
RIGHT SPEAKER
+
_
+
_
+
_
SURROUND
LEFT SPEAKER
+
_
Figure 2 – Speaker Connections

SPEAKER AND AUDIO CONNECTIONS
CD PLAYERAM AntennaFM Antenna
AUDIO RECORDER
L R Optical Coax
REC/IN
PLAY/OUT
Step 4. ConnectAM and FM antennas (Fig. 4) (see page 16).
Step 5. Connect source components,as shown in Figures 4 and 5, and the
Device Connection Options chart on the back of this guide (see
pages 16–17).
AUDIO connections: Right channel (red) on source to right (red)
on AVR, and left channel (white) on source to left (white) on AVR.
DIGITAL AUDIO connections, if available: Choose either coaxial
(orange) to coaxial (orange) OR optical to optical for each device.
The Coaxial 1 input defaults to the DVD player; however, it may be
reassigned.Assign the other digital inputs and outputs as appropriate
for your equipment (see Step 7).
VIDEO connections: Choose component (Y/Pb/Pr – green/blue/
red), composite (yellow) or S-Video (4-pin) for each video source.
The Component Video 1 inputs default to the DVD player, but may be
reassigned. Connect the component, composite and S-Video Monitor
outputs to your Video Monitor (TV).Switch your TV set’s input to
match the type of video used for the currently selected source.
Step 6. Plug all components into AC power outlets.The outlets on the back
of the AVR 630 should be used only for low-current products, such
as CD or DVD players, and the total should not exceed 100 watts.
Basic Receiver Configuration
Step 7. Select digital inputs: If your DVD is connected to Coaxial 1, no
adjustment is needed. For any other digital-device connections, use
the front-panel Digital Select button and the arrow buttons to select
an optical or coaxial digital input (see pages 21 and 32).
Step 8. Configure speakers: No action is needed if you have five “small”
satellite-type speakers and a subwoofer. Otherwise,press the Speaker
button and then the Set and arrow buttons to select the correct
speaker choices for your system (see pages 23–25).
Step 9. Set the Output Levels with EzSet: Set the Volume to –15dB.
Sit in the listening position and hold the remote in front of you at
shoulder level, pointing it at the AVR. Press the EzSet button on the
remote, and then the Set button when it lights red. Following the
instructions in the remote’s LCD display, press the button on the
remote until the display shows the number of speakers in your system
and then press the Set button again. Hold the remote steady until the
LCD display flashes a COMPLETE message (see page 26).
Step 10.
Your system is configured – sit back and enjoy!
Figure 4 –Audio Connections
Dashed lines (––––) indicate coaxial and optical
digital audio connections. Choose either type
(but not both) for each digital audio source.

DVD PLAYER
VCR (Video 1)
In/Rec
Out/Play
L R VIDEO
Component Video
Y
Pb
Pr
Optical Coax
L R Video S-Video
Cable Box or Satellite Receiver (Video 3)
OUT
L R Video S-Video
Optical Coax
Component Video
Y
Pb
Pr
TV or Video Display
IN
Video S-Video Component Video
Y Pb Pr
VIDEO CONNECTIONS
Device Connection Options:Recommended connections are shown in red, but connections may be made to best fit your system requirements.The Video 4,Coaxial 3 and Optical 3 inputs are on the front panel of the receiver.
Device Input Name Audio Input Connections Audio Output Connections Video Connections
CD Player CD CD L/R Inputs, Optical Digital 1 or 2,or Coaxial Digital 1 or 2Not required Not required
DVD Player DVD Coaxial Digital 1 or 2, Optical Digital 1 or 2,or DVD L/R Inputs Not required Component V1, DVD Composite or S-Video
VCR Video 1 Video 1 L/R Inputs Video 1 L/R Outputs Video 1 Composite or S-Video Input and Output
Cable Box or Satellite Receiver Video 3 Video 3 L/R Inputs,Optical Digital 3*,or Coaxial Digital 3*Inputs Not required Component V2,Video 3 Composite or S-Video
Audio Recorder Tape Tape L/R Inputs, Optical Digital 1/2** or Coaxial Digital 1/2** Inputs Tape L/R Outputs, Digital Optical** or Coaxial Outputs** Not required
TV orVideo Display Not applicable Not required Not required Monitor-Out Component,Composite and/or S-Video
*Check with your cable company to determine whether digital audio is available for all channels. It may be necessary to make BOTH analog and digital connections if it is not. **Digital audio recorders only.
250 Crossways Park Drive,Woodbury, New York 11797 www.harmankardon.com © 2003 Harman International Industries,Incorporated Part No.ZK-C11-16HA-00
Power for the Digital Revolution.
®
®
Figure 5 –Video Connections
Dashed lines (––––) indicate coaxial and optical digital audio connections. Choose either type (but not both) for each
digital audio source.
Dotted lines (••••) indicate component, composite or S-Video connections.Component video is the preferred connection
when available, but you may use any of the three types (but not more than one).When component, composite and
S-Video sources are connected to the AVR you must also connect all outputs from the AVR to your TV.