Harrod Sport FBL-848-4G User manual

A minimum of 2 people are required for this assembly
Estimated 30 minutes assembly time (not including sockets)
INS847
Revision 1
03/08/2021
FBL-848-4G
7.32x2.44m 4G Stadium Pro Goal
30
mins
iIMPORTANT: Please read these assembly instructions carefully
before starting to assemble your goal
IMPORTANT: mustThis goal be secured in sockets concreted into
the ground to at least the specification detailed in this document
i
ASSEMBLY INSTRUCTIONS
PENDING
PATENT
GB2552496
GB2585031

Pack Contents
Code
Product
FBL-848-4G
7.32x2.44m 4G Stadium Pro Goal
Stadium Pro Goal
1. Crossbar
2. L/H Upright
3. R/H Upright
4. Socket
5. Socket Lid 1.
x2
(FPS273)
*parts are not to scale
ode in brackets refers
to packed parts
**c
Page 1
2.
x2
(FPS276)
3.
x2
(FPS276)
Tools Required
4mm
1x 4mm Allen Key (supplied)
6mm
1x 6mm Allen Key (supplied)
1x Spirit Level
Optional Extras
FBL-849-4G: 2 Post Freehanging Net
Supports
FBL-190-4G: Steel Bottom Hinged Net
Supports
FBL-200-4G: Aluminium Bottom Hinged
Net Supports
FBL-851-4G: Pro Bottom Net
Support
FBL-303: Hexagonal Box Net
FBL-308: Square Box Net
4.
x4
WEQ338 (SKT-001)
5.
x4
WEQ339 (SKT-001)

Code
Product
FBL-848-4G
7.32x2.44m 4G Stadium Pro Goal
FPK847: 4G Stadium Pro Fittings
A. Upright Connector
B. Socket Wedge
C. M10x20mm Flange Screw
D. M10x40mm Button Screw
E. M10x30mm Button Screw
F. M6x8mm Button Screw
G. M10x16mm Grub Screw
H. M10 Nord-Lock Washer
I. Net Holder Clip
J. Locking Plate
K. Bolt Plate
L. Net Clip
M. 6mm T-Bar Hex Driver
Fittings Pack Contents
C.
x4
BOL347
Page 2
*parts are not to scale
A.
x4
PEP899
B.
x4
APS128
F.
x4
BOL678
D.
x4
BOL321
E.
x16
BOL353
L.
x240
HKS070
M.
x2
BOL803
J.
x4
PPS211
H.
x16
BOL757
I.
x4
CLP055
G.
x4
BOL349
K.
x4
PPS212
Glued together Pair
(do not break apart)

Socket Installation
Code
Product
FBL-848-4G
7.32x2.44m 4G Stadium Pro Goal
Page 3
1Dig 2 holes, L600mm x W600mm x D645-700mm, with the centre of each hole in the centre of the
goal line, 7422mm apart. Position the Sockets (4) centrally in the hole with the top of each Socket
sitting 45mm below ground level, ensure the straight edge of the Socket is perpendicular to the goal line
and the Sockets are sitting vertical. Leave a drainage hole below each socket to allow rainwater to drain
through the concrete. Fill the hole until the concrete sits between 45 and 100mm below ground level.
4
45mm 45-100mm
600mm
600mm
Concrete
7422mm
WARNING: fullyAllow concrete to set before inserting uprights.
!
Plan View
Goal
Line
4
90°
112mm
122mm
IMPORTANT: Consult construction engineer for advice where
required
i
502mm

Code
Product
FBL-848-4G
7.32x2.44m 4G Stadium Pro Goal
Assembly Instructions
1
6mm
Page 4
1
1
E
H
A
A
3
C
J
C
J
2
32
32
K
J
6mm
(Only required if a Pro Bottom Hinged
Net Support is being fitted)

Code
Product
FBL-848-4G
7.32x2.44m 4G Stadium Pro Goal
6mm
1
2
3
1
E
H
E
3
1
WARNING: Carefully lower the goal into the sockets. Dropping the
goal in can cause damage to the adjustment mechanism.
!
GL
GL
Page 5
3
If a Bottom Hinged Net Support is being fitted; refer to appropriate instruction and fit the
hinge assembly before proceeding.

Code
Product
FBL-848-4G
7.32x2.44m 4G Stadium Pro Goal
Page 6
2.44m
WARNING: socket wedge is loosened
net tension removed
Once fitted, ensure the and
the before adjusting the goal height. Failure
to do so will damage the raising mechanism.
!
B
360°=0.9mm
WARNING: low torque settingUse power tools with only to
adjust goal height. Applying high torque to mechanism may
cause irreparable damage.
!
M
D
D
B
6mm

Net
FBL-190
FBL-200
FBL-849
FBL-303
FBL-308
Net Support
Weight
Matrix
83.5 70.5 104.5
85.5 72.5 106.5
70.5
eg, if using an FBL-303 Net with an FBL-200 Bottom Hinged
Net Support, the goal system will weigh 70.5kg as below;
Net
Code
Product
FBL-848-4G
7.32x2.44m 4G Stadium Pro Goal
Page 7
I
F
L
L
HINT: Please refer to Hinged Net Support and Freehanging Net
Support instructions to complete the net setup.
4mm
6mm Net
FBL-190
FBL-200
FBL-849
FBL-303
FBL-308
Net Support
Weight
Matrix
This 7.32x2.44m Football Goal conforms to:
Provided it is anchored/installed as per the
manufacturer’s instructions
BS EN 748:2013
Manufactured in the UK by Harrod Sport in:
FIFA Certification number;
This goal is designed to be used for football
only and no other purpose
Check all fastenings are fully tightened before
using this product and check periodically
afterwards
At all times the goal shall be secured •
against tilting
Do not climb on the net or goal framework
Corresponding net designs;
-Box
- Straight Back
- Standard
LBL850
Goal System Weight; kg
FIFA Certification Conformance
In order for your goal to conform to FIFA’s quality programme, the total weight of the Goal, including
Bottom Net Support and Net, must be listed on the conformance label. Please use the table below to
identify the weight of your system configuration and fill in the label on the upright in the box as shown.
83.5 70.5 104.5
85.5 72.5 106.5
G