Hartmann T2hck5 User manual

T2HCK5

Up to 16 Door Kit

Fully assembled kit includes:

- Trove2 enclosure with THC2 Altronix/Hartmann Controls backplane

- One (1) AL1012ULXB - Power Supply/Charger

T2HCK78

8 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove2 enclosure with THC2 Altronix/Hartmann Controls backplane

- One (1) AL1024ULXB2 - Power Supply/Charger

- One (1) ACMS8 - Dual Input Fused Access Power Controller

- One (1) VR6 - Voltage Regulator

- One (1) PDS8 - Dual Input Fused Power Distribution Module

T2HCK75

Up to 16 Door Kit

Fully assembled kit includes:

- Trove2 enclosure with THC2 Altronix/Hartmann Controls backplane

- One (1) AL1024ULXB2 - Power Supply/Charger

- One (1) AL1012ULXB - Power Supply/Charger

T2HCK7516

Up to 16 Door Kit with Fused Outputs

Fully assembled kit includes:

- Trove2 enclosure with THC2 Altronix/Hartmann Controls backplane

- One (1) AL1024ULXB2 - Power Supply/Charger

- One (1) AL1012ULXB - Power Supply/Charger

- Two (2) ACMS8 - Dual Input Fused Access Power Controllers

Access & Power Integration

Rev. T2HCL011122

Installing Company: _________________________ Service Rep. Name: __________________________________________

Address: _________________________________________________________ Phone #: _________________________

All registered trademarks are property of their respective owners.

Installation Guide

All components of these Trove kits are UL Listed sub-assemblies.

Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

- 2 - THC2 ULXB Kits Installation Guide

Overview:

Altronix Trove Hartmann Controls kits are pre-assembled and consist of Trove enclosure with factory installed Altronix power supply/chargers and

sub-assemblies. Each kit also accommodates up to two (2) Hartmann Controls PRS_Master boards and up to eight (8) PRS_TDM or PRS_IO8 boards.

Configuration Chart:

Altronix

Model Number

115VAC 60Hz

Input Current (A)

Power Supply Board

Input Fuse Rating

Power Supply Board

Battery Fuse Rating

Nominal DC Output Voltage Options

Maximum

Supply Current for

Main Outputs on

Power Supply board

and ACMS8 Access

Power Controller’s

outputs (A)

Fail-Safe/Fail-Secure or

Dry Form “C” Outputs

Current Per

ACMS8 Output (A)

ACMS8 Board

Input Fuse Rating

ACMS8 Board Output

Fuse Rating

PDS8 Board

Input Fuse Rating

PDS8 Board

Output Fuse Rating

Power Supply 1 Power Supply 2

[DC] [DC]

12VDC

Output

Range

(V)

24VDC

Output

Range

(V)

12VDC

Output

Range

(V)

24VDC

Output

Range

(V)

T2HCK5 2.6 5A/250V 15A/

32V

AL1012ULXB N/A

12VDC @ 10A ––––––

10.0-

13.2 – –

T2HCK78 3.5 5A/250V 15A/

32V

AL1024ULXB2 N/A

12VDC @ 9.4A 8 2.5 15A/

32V

3A/

32V

10A/

32V

3A/

32V

–20.19-

26.4 –

T2HCK75 6.8 5A/250V 15A/

32V

AL1024ULXB2 AL1012ULXB AL1024ULXB2:

24VDC @ 9.2A ––––––

–20.19-

26.4

10.0-

13.2 –AL1012ULXB:

12VDC @ 10A

T2HCK7516 6.8 5A/250V 15A/

32V

AL1024ULXB2 AL1012ULXB AL1024ULXB2:

24VDC @ 9.2A 16 2.5 15A/

32V

3A/

32V – –

–20.19-

26.4

10.0-

13.2 –AL1012ULXB:

12VDC @ 10A

Hardware and Accessories:

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.

Product is intended for indoor use only.

1. Remove backplane from enclosure. Do not discard hardware.

2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws

in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure.

Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install

the three fasteners. Place the enclosure’s upper keyholes over the three upper screws.

Install the three lower screws and make sure to tighten all screws.

3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in desired location,

opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately 2” from the

right side (Fig. 1, pg. 2). Connect tamper switch wiring to the Access Control Panel input or the

appropriate UL Listed reporting device. To activate alarm signal open the door of the enclosure.

4. Mount Hartmann Controls boards to backplane, refer to pages 3-6.

5. Refer to the ULXB Power Supply/Charger Installation Guide for AL1024ULXB2 and AL1012ULXB

and corresponding Sub-Assembly Installation Guides for the following models: ACMS8, PDS8 and

VR6 for further installation instructions.

Fig. 1

Tamper Switch

(included)

To Access Control Panel or

UL Listed Reporting Device

Edge of

Enclosure

Nylon or Metal Spacer | 5/16” Pan Head Screw | Lock Nut

THC2 ULXB Kits Installation Guide - 3 -

T2HCK5: Configuration of Hartmann Controls Boards:

1. Align the Hartmann Controls boards on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten spacers (provided) to pems that match the hole pattern for Hartmann Control boards (Fig. 2, 2a, pg. 3).

Note: Hartmann Controls boards must be properly grounded.

Please use provided metal spacers for the lower right mounting holes (Fig. 2, pg. 3).

3. Mount Hartmann Controls boards to spacers utilizing provided 5/16” pan head screws (Fig. 2a, pg. 3).

4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).

PRS_MASTER

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_MASTER

Metal Spacer

+ BAT -

L G N BAT FAIL NC C NO NC C NO AC FAIL

AC DC

- DC +

AL1012ULXB

Pem

Spacer

Hartmann Controls

Board

Backplane

Pan Head

Screw

Fig. 2a

Fig. 2 - T2HCK5 Conﬁguration

- 4 - THC2 ULXB Kits Installation Guide

T2HCK78: Configuration of Hartmann Controls Boards:

1. Align the Hartmann Controls boards on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten spacers (provided) to pems that match the hole pattern for Hartmann Control boards (Fig. 3, 3a, pg. 4).

Note: Hartmann Controls boards must be properly grounded.

Please use provided metal spacers for the lower right mounting holes (Fig. 3, pg. 4).

3. Mount Hartmann Controls boards to spacers utilizing provided 5/16” pan head screws (Fig. 3a, pg. 4).

4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).

PRS_MASTER

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_MASTER

Metal Spacer

PWR1 +

PWR2 +

COM -

PWR2 +

PWR1 +

+ PWR2 --

+ PWR1 --

Altronix - ACMS8

+ INP1 --

OFF

IN1

IN2

Out1

<1 off 2>

PWR1 +

PWR2 +

COM ---

+ INP2 --

IN2 Fuse

IN1 Fuse

Common Power Outputs (NEG)

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

3333 33

Out2

<1 off 2>

Out3

<1 off 2>

Out4

<1 off 2>

Out5

<1 off 2>

Out6

<1 off 2>

Out7

<1 off 2>

Out8

<1 off 2>

Altronix - PDS8

Altronix VR6 is mounted under ACMS8

AL1024ULXB2

BAT FAIL

AC FAIL

- BAT + + DC -

AC DELAY

Pem

Spacer

Hartmann Controls

Board

Backplane

Pan Head

Screw

Fig. 3a

Fig. 2 - T2HCK78 Conﬁguration

THC2 ULXB Kits Installation Guide - 5 -

T2HCK75: Configuration of Hartmann Controls Boards:

1. Align the Hartmann Controls boards on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten spacers (provided) to pems that match the hole pattern for Hartmann Control boards (Fig. 4, 4a, pg. 5).

Note: Hartmann Controls boards must be properly grounded.

Please use provided metal spacers for the lower right mounting holes (Fig. 4, pg. 5).

3. Mount Hartmann Controls boards to spacers utilizing provided 5/16” pan head screws (Fig. 4a, pg. 5).

4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).

PRS_MASTER

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_MASTER

Metal Spacer

AL1024ULXB2

BAT FAIL

AC FAIL

- BAT + + DC -

AC DELAY

+ BAT -

L G N BAT FAIL NC C NO NC C NO AC FAIL

AC DC

- DC +

AL1012ULXB

Pem

Spacer

Hartmann Controls

Board

Backplane

Pan Head

Screw

Fig. 4a

Fig. 4 - T2HCK75 Conﬁguration

- 6 - THC2 ULXB Kits Installation Guide

T2HCK7516: Configuration of Hartmann Controls Boards:

1. Align the Hartmann Controls boards on the backplane to match the boards’ mounting holes with corresponding pems.

2. Fasten spacers (provided) to pems that match the hole pattern for Hartmann Control boards (Fig. 5, 5a, pg. 6).

Note: Hartmann Controls boards must be properly grounded.

Please use provided metal spacers for the lower right mounting holes (Fig. 5, pg. 6).

3. Mount Hartmann Controls boards to spacers utilizing provided 5/16” pan head screws (Fig. 5a, pg. 6).

4. Fasten backplane to Trove2 enclosure utilizing lock nuts (provided).

PWR1 +

PWR2 +

COM -

PWR2 +

PWR1 +

+ PWR2 --

+ PWR1 --

PWR1 +

PWR2 +

COM -

PWR2 +

PWR1 +

+ PWR2 --

+ PWR1 --

PRS_MASTER

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_TDM or PRS_IO8

Metal Spacer

PRS_MASTER

Metal Spacer

Altronix - ACMS8

AL1024ULXB2

BAT FAIL

AC FAIL

- BAT + + DC -

AC DELAY

+ BAT -

L G N BAT FAIL NC C NO NC C NO AC FAIL

AC DC

- DC +

AL1012ULXB

Pem

Spacer

Hartmann Controls

Board

Backplane

Pan Head

Screw

Fig. 5a

Fig. 5 - T2HCK7516 Conﬁguration

THC2 ULXB Kits Installation Guide - 7 -

Notes:

- 8 - THC2 ULXB Kits Installation Guide

Enclosure Dimensions (H x W x D approximate):

27.25” x 21.5” x 6.5” (692.2mm x 552.5mm x 165.1mm)

6.75” (171.5mm)8.25” (209.5mm)

8.00” (203.2mm)

2.00” (50.8mm)

1.25” (31.8mm)

5.25” (133.4mm) 5.25” (133.4mm)7.00” (177.8mm)

1.25” (31.8mm)

6.25” (158.8mm) 19.80” (502.9mm)

1.00” (25.4mm)

27” (685.8mm)

1.5”

(38.1mm)

2.00” (50.8mm) 2.00” (50.8mm)

3.5”(88.9mm) 3.5”(88.9mm)

21.50” (546.1mm)

5.25” (133.35mm) 5.25” (133.35mm)

6.25” (158.8mm)

1.25”

(31.8mm)

0.85” (21.6mm)

0.5625” (14.3mm)

2.415” (61.3mm)

0.685” (17.4mm)

1.77”

(45mm)

0.885” (22.5mm)

1.125” (28.3mm)

Knockouts

2.00” (50.8mm) 2.00” (50.8mm)

Hartmann Controls is not responsible for any typographical errors.

–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

10 Lockhart Rd, Barrie, ON L4N 9G8, Canada | phone: 1-877-411-0101

web site: www.hartmann-controls.com | e-mail: [email protected]

IITHC2 ULXB Kit Series A11V

This manual suits for next models

Table of contents