Hasbro PlayDoh Creativity Table 22613 User manual

Phillips/cross head screwdriver (not included) required for assembly.
AGES 3+
22613
CONTENTS: 8 five-ounce cans and 4 two-ounce cans of PLAY-DOH® Brand
Modeling Compound (Net Weight 48 oz., 1357 grams), tabletop center,
2 tabletop ends, 4 table legs, carousel, roller, ruler, FUZZY PUMPER®
extruder, extruder ring, extruder post, extruder rail, FUN FACTORY®
extruder, 20 cutters and rollers, 4 shelves, 4 crayons, 4 markers, 10 sheets
of paper, bag of screws, and instructions.
C rea t i v i t y Ta bl e™ C rea t i v i t y Ta bl e™
CAUTION:
Adult assembly required.
This product contains small parts
which are necessary for assembly. Prior to and
during assembly of this product, keep small
parts out of children’s reach. Small parts pose
a choke hazard to children under 3 years.

ASSEMBLY
RULER
ROLLER
4. Stand table on legs. Snap
carousel onto tabletop.
Snap FUZZY PUMPER®
post onto tabletop. Snap
FUN FACTORY® extruder
onto tabletop.
5. Fit 4 shelves into either of
the legs with shelf slots.
6. Slide roller onto ruler.
3. Push and snap legs onto table as shown. Be sure to match the
letter on the leg with the letter on the table.
2. Turn tabletop assembly
over. Use a Phillips/
cross head screwdriver
to tighten 3 screws into
tabletop center/end on
one side. Repeat for
other side.
1. Fit 2 tabletop ends onto tabletop center.
TABLETOP
CENTER
TABLETOP ENDS
FUZZY PUMPER POST
CAROUSEL
FUN FACTORY
EXTRUDER
SHELVES
NOTE: Be sure
to insert each
table leg at a
slight angle (as
shown). Gently
rock each leg
into place until
an audible
“snap” is heard.

FUZZY PUMPER
1. Fill FUZZY PUMPER extruder with
PLAY-DOH compound.
2. Slide extruder ring over extruder.
3. Slide FUZZY PUMPER extruder onto
post to extrude compound!
DRAWING
1. Use the markers and crayons to
write, draw pictures on the paper!
RULER DESIGNS
1. Press PLAY-DOH compound
into recess in ruler.
2. Place extruder rail over
compound.
3. Slide the roller over the rail for
cool creations!
FUN FACTORY
1. Fill FUN FACTORY extruder with
PLAY-DOH compound.
2. Slide the extruder rail on and choose
the shape you want.
3. Press the FUN FACTORY handle to
extrude compound!
PLAY FEATURES

I Want My Play-Doh®, Please!
Fun to play with, but not to eat.
Molded results vary depending on child’s age and level of skill.
Product and colors may vary.
NOTICE TO PARENTS: CONTAINS WHEAT
NONTOXIC. CONFORMS TO ASTM D-4236
PLAY-DOH and the PLAY-DOH logo are trademarks identifying
quality modeling compound products produced exclusively by
Hasbro, Inc.
© 2005 Hasbro. All Rights Reserved.
TM & ® denote U.S. Trademarks.
U.S. Patent No. 6,713,624
22613 P/N 6486210000
EASY 3-STEP CLEANUP!
1. Place PLAY-DOH Brand Modeling Compound back in cans
and seal lid.
2. Remove excess from carpets/fabrics, then allow remaining
compound to dry.
3. Loosen dried compound with stiff brush and vacuum clean. If
necessary, brush with gentle soap and cold water. (Do not use hot
water or cleaning solutions to clean PLAY-DOH compound from
carpets/fabrics.)
Note to parents: Markers and crayons may stain certain surfaces.
Use soap and warm water to clean.
PLAYDOH.COM
PLAYDOH.COM
FOR NEW PRODUCTS AND OFFERS
FOR NEW PRODUCTS AND OFFERS
Questions? Call: 1-800-327-8264
STORAGE
- Store PLAY-DOH® Brand Modeling Compound cans in the can
holders on the shelves.
- Place crayons and markers in the carousel.
- Store roller on a shelf; store ruler and extruder rail in paper tray.