Hasley Taylor HBW8AQ 1P Series User manual

PAGE 1 0000000956 (Rev. C - 11/16)
HBW8AQ*1P HBW8AQ*2P HBW*M*L*R
OWNERS MANUAL
HBW8 Semi-Recessed Wall Mount Water Cooler

PAGE 2
0000000956 (Rev. C - 11/16)
HBW8AQ*1P HBW8AQ*2P HBW*M*L*R
514
FIG. 1
4
SEE
FIG. 4
SEE FIG.3
15
12
21
10
11
16
19
6
3
7
8
18
20
2
13
1
9
14
22
23
SEE
DETAIL
ABOVE
24
NOTE: Non-refrigerated units do not include all electrical and refrigeration
components shown above. Other components and rough-in are the same as shown.
11
5
25
Uses HFC-134A refrigerant
Note: Danger! Electric shock hazard. Disconnect power before servicing unit.

PAGE 3 0000000956 (Rev. C - 11/16)
HBW8AQ*1P HBW8AQ*2P HBW*M*L*R
C
L
6"
152mm
9 1/2"
241mm
3 1/2"
89mm 18"
457mm
20 1/4"
514mm
16 3/4"
425mm
40"*
1016mm
6 3/8"
162mm
6 3/8"
162mm
2 5/8"
67mm
18 3/4"
476mm
1"
25mm
1 1/2"
38mm
3/4"
9mm
1 1/2"
38mm
3/4"
9mm
5 1/4"
140mm
4"
102mm
3"
76mm
23 1/2"
597mm
24"
610mm
26"
660mm
E
E
C
D
B
A
G
F
3 1/4"
83mm 3 1/4"
FIG. 2
* RECOMMENDED HEIGHT FOR ADULTS. DECREASE
HEIGHT FOR CHILDREN.
FINISHED FLOOR
LEGEND/LEYENDA/LÉGENDE
A = RECOMMENDED WATER SUPPLY LOCATION 3/8" O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38 mm) OUT FROM WALL SHUT OFF BY OTHERS
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN
C = 1-1/4" TRAP NOT FURNISHED**
D = ELECTRICAL OUTLET LOCATION
E = INSURE PROPER VENTILATION BY MAINTAINING 4" (102mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL.
F = POWER CORD 1-1/2FEET (457mm) LONG
G = 5/16" (8mm) SCREW HOLES IN MOUNTING PLATE

PAGE 4
0000000956 (Rev. C - 11/16)
HBW8AQ*1P HBW8AQ*2P HBW*M*L*R
FIG. 3
Stream height is factory set at 35 PSI. If supply pressure varies greatly from this,
remove Locknut and Button and adjust screw on Regulator. Clockwise adjustment will raise
stream and counter-clockwise adjustment will lower stream. For best adjustment, stream should
hit basin approximately 6-1/2" (165mm) from bubbler.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
HANGER BRACKETS & TRAP INSTALLATION
1) Remove hanger brackets fastened to back of cooler by removing screws.
2) Mount the hanger brackets and trap as shown in Figure 2.
NOTE: Hanger Brackets and trap MUST be supported securely. Add xture support carrier if wall will not provide adequate
support.
IMPORTANT:
- 5-1/2 in. (140mm) dimension from wall to centerline of trap must be maintained for proper t.
- Anchor hanger securely to wall using all mounting holes.
3) Install straight valve for 3/8" O.D. unplated copper tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger brackets. Be certain the hanger brackets are engaged properly in the frame and wrapper.
5) Remove the access panel on the underside of the cooler and set it aside.
6) Connect water inlet line--See Note 4 of General Instructions.
7) Remove the slip nut and gasket from the trap and install them on the cooler waste line making sure that the end of the waste
line ts into the trap. Assemble the slip nut and gasket to the trap and tighten securely.
START UP
Also See General Instructions
8) Replace the front panel and secure by retightening all screws.
CORRECT STREAM HEIGHT
FIG. 4
WRAPPER
17
LOCKNUT BUTTON
REGULATOR

PAGE 5 0000000956 (Rev. C - 11/16)
HBW8AQ*1P HBW8AQ*2P HBW*M*L*R
ITEMIZED PARTS LIST
ITEM NO. PART NO. DESCRIPTION
36208C
27095C
98775C
98533C
20415C
98776C
66703C
36322C
0000000238
98778C
98356C
26664C
75536C
98773C
0000000886
55996C
98536C
27093C
28797C
27097C
27094C
See Color Table
0000000252
70817C
20430C
56092C
Power Cord
Fan Bracket
Kit - Fan Motor Assy/Blade/Motor/Shroud/Screws/Nut
Kit - Bubbler/Nipple/Gaskets
Hanger - Bracket
Kit - Condenser/Drier
Drier
Compressor Serv. Pak
Kit - Compr Electrical /Relay/Overload/Cover
Kit - Heat Exchanger/Drier
Kit - Drain/Tailpipe/Strainer Assy/Gasket
Basin - Stainless Steel
Screw - Basin Mtg.
Kit - Cold Control/Screws
Kit - Evaporator Assembly
Strainer
Kit - Push Button Assy/Regulator/Holder/Button/Nuts
Angle - Front Corners
Bracket - Basin Mounting
Frame - Back/Bottom
Bracket - Front
Wrapper
Kit - Compr Mtg Hdwe/Grommets/Clips/Washers
Fitting - Elbow 1/4 Stem
Hanger - Bracket
Poly Tubing (Cut to Length)
1
2
3
4
5
6
7
*8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
NS
*INCLUDES RELAY & OVERLOAD. IF UNDER WAR-
RANTY, REPLACE WITH SAME COMPRESSOR USED IN
ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the above
water coolers or orders for repair parts MUST include Model
No. and Serial No. of cooler, name and part number of re-
placement part.
COLOR TABLE
PANEL COLOR Item No. 22
Part No.
Almond Vinyl
Platinum Vinyl
Stainless Steel
Slate Vinyl
21481C
26943C
21013C
26949C
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A.
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM
220V 50Hz
35827C
0000000244
1000002147
98751C
35826C
Power Cord
Kit - Fan Motor Assy/Motor/Blade/Shroud/Nut
Compressor Serv. Pak 220V
Kit - Compr Electrical /Relay/Overload/Cover
Power - Inlet
PART. NO. DESCRIPTION
ITEM NO.
1
3
*8
9
-