HATO 400Y User manual

HATO 400Y
AUTOMATION MANUAL
FOR SLIDING GATES
WITH SLOW DOWN

Congratulations on your purchase of a sliding gate controller and welcome to the users of
HATO products. Declarations of conformity and manuals for HATO POLSKA S.C. products can e
downloaded from the we site: http://www.hato.com.pl
Before assem ling and using the arrier for the first time, read the manual carefully and
keep them for future reference.
In accordance with the provisions of the Machinery Directive 2006/42 / WE, it is declared
that the product may not e put into operation until the final machine, into which it is uilt or a
su assem ly of which it is uilt, o tains a declaration of compliance with the directives and
relevant regulations, which the final machine must meet.
RECOMMENDATIONS AND PRECAUTIONS
Before installing and using the drive, carefully read all warnings and safety rules. Incorrect
installation and non-compliance with the standards contained in the manual may result in serious
accidents.
All installation work should e carried out in accordance with applica le regulations and
standards.
The driver installation may only e performed y qualified and authorized personnel.
Installation should e carried out with asic ESD protection.
Be especially careful during assem ly! The controller uses 230Vac voltage (life and health
threatening).
All works related to the proper functioning of the device (connection, start-up, operation)
must e carried out in accordance with the applica le regulations in the field of electrical
equipment operation and in accordance with health and safety regulations.
Do not connect the drive to the power supply earlier than specified in the manual, failure
to do so may result in electric shock.
Before starting the installation, check the mechanical condition of the arrier: it should not
sway excessively, it should move easily and smoothly.
Before installation, remove unnecessary items and secure accessories, such as locks.
During assem ly, children, handicapped persons and motor vehicles must not e in the
vicinity of the arrier.
All fixed control elements should e located near the arrier, ut away from moving parts
and out of the reach of outsiders.
Before repairing or removing any parts of the arrier, disconnect power.Children and
people with intellectual disa ilities cannot control the arrier on their own.
Configuration of overload and thrust settings may only e performed y qualified
personnel.
Fluorescent lamps must not e used as traffic lights.
This roduct may only be used for its intended ur ose. Im ro er use is im ro er and
dangerous. The manufacturer of the roduct is not liable for any damage caused by im ro er or
negligent use.

Failure to follow the instructions a ove may result in serious injury or
equipment damage. The manufacturer is not lia le for damage and
malfunctions resulting from failure to o serve these installation and
operating instructions.
In accordance with the regulations in force on the disposal of
waste equipment y private users in the European Union, items
earing this sym ol MUST NOT e disposed of with other ru ish. In
this case, the user is responsi le for proper disposal y delivering the
device to a designated point, or to the manufacturer who will take
care of its further disposal. Separate collection and recycling of
unnecessary devices helps to protect the environment and ensures
that disposal is done in a way that protects human health and the
environment. This note also applies to waste atteries and
accumulators.
TABLE OF CONTENTS
RECOMMENDATIONS AND PRECAUTIONS........................................................................................................2
2. IMPORTANT SAFETY INSTRUCTIONS.............................................................................................................4
DESCRIPTION AND PRINCIPLE
OF THE OPERATION OF THE CONTROLLER........................................................................................................6
PURPOSE.........................................................................................................................................6
CONTROLLER ADVANTAGES....................................................................................................6
DRIVER INSTALLATION......................................................................................................................................7
1.1.Connecting the imit switch for opening and c osing.................................................................7
The imit switch for opening and c osing is used to precise y stop the gate in the c osed or open
position. Adjust the position of the magnets so that the gate opens and c oses accurate y. ............7
1.2.Connecting photoce s................................................................................................................7
1.3.Connection of the manua contro ..............................................................................................8
1.4.Pu se generator connection - OPTIONAL.................................................................................8
1.5.Capacitor connection..................................................................................................................8
1.6.Motor connection........................................................................................................................8
1.7.Connection of signa ighting ....................................................................................................8
1.8.Power connection.......................................................................................................................8
CONNECTION DIAGRAM...................................................................................................................................9
SETTING PROGRAMMING...............................................................................................................................10
TRAFFIC LIGHTS........................................................................................................................10
FLASHING ON / OFF (Defau t: enab ed).....................................................................................10
AUTOCLOSE FUNCTION...........................................................................................................11
ENGINE OPERATION PROGRAMMING...................................................................................12
RESTORING DEFAULT SETTINGS - 60s operation without encoder and without dece eration
........................................................................................................................................................14

WICKET FUNCTION...................................................................................................................14
OPEN ONLY FUNCTION.............................................................................................................16
PHOTO CLOSE FUNCTION........................................................................................................17
LIMIT SWITCH TYPE..................................................................................................................17
DELETING ALL TRANSMITTERS.............................................................................................17
PROGRAMMING OF TRANSMITTERS....................................................................................18
TECHNICAL SPECIFICATION.............................................................................................................................19
DECLARATION OF CONFORMITY.....................................................................................................................19
........................................................................................................................................................................19
WARRANTY CONDITIONS................................................................................................................................20
1. DESCRIPTION AND PRINCIPLE OF OPERATION OF THE DRIVE
The HATO 400Y drive is designed for sliding gates. It has een equipped with an auto-reverse function,
infrared sensors, partial opening (pedestrian crossing), mechanical unlocking ena ling manual opening in
the event of failure of the drive controller. The device consists of a single-phase motor and a worm gear. The
main motor shaft rotates the worm, driving the worm gear and pinion, moving the rack attached to the
gate, there y causing it to shift. In the event of an electrical failure, you can release the motor lock and push
the gate y hand. The device has a temperature sensor installed, which automatically turns off the engine at
120 ° C and turns it on when the temperature drops to 85 ° C +/- 5 ° C.
The applied system of rolling coding of Microchip remote controls makes the system unavaila le to an
unauthorized person.
2. IMPORTANT SAFETY INSTRUCTIONS
The drive and the sliding gate should e installed in accordance with the instructions presented in Fig. 1. It
is recommended to install stops at oth ends of the gate to prevent it from falling out of the rails. The rails
must e installed horizontally. To ensure adequate sta ility, the drive foundation should e made of
concrete. Electric wires must e secured with a suita le installation pipe. If a hand switch is installed, use
two pipes: one for the power cord and the other for the low voltage wire (to the utton). The method of
fastening the drive is shown in Fig. 2, the drive can e attached to the so prepared mounting ase. Fix the
rack to the gate with screws and adjust it so that it fits exactly with the pinion. The distance etween the rail
and the wheel should e approx. 0.5-1 mm.

3. MOUNTING OF THE LIMIT SWITCH CAMS
Fig. 3.

Fig. 4
The cams of the limit switch should e mounted on the toothed rack ar. They should e pre-
installed in such a way that the eginning of pressure on the limit switch is a out 10 cm efore the
complete opening (closing) of the gate. The exact setting is made after starting the drive.
DESCRIPTION AND PRINCIPLE
OF THE OPERATION OF THE CONTROLLER
PURPOSE
The HEL B11 controller is designed for gate drives using 230Vac motors with a power of up
to 500W. Perfect for continuous operation, it can e used on private properties and in companies.
The used system of varia le coding of Microchip transmitters makes it unavaila le to an
unauthorized person.
CONTROLLER ADVANTAGES
• Soft start function increasing the life of the door.
• Control y means of remote-control transmitters (up to 28 pcs.) On the frequency of 433.92
MHz with a dynamic Keeloq code.
• Control of the monosta le utton ( ell type).
•AUTO CLOSE function.
•ONLY OPEN function (estate function).
•WICKET function.
• Adjustment of the thrust - when working with the encoder turned off.
• Overload control - when working with the encoder support turned on.
• Working time adjustment.
• A release function efore reaching the limit switch
• Remote programming of engine operation (using transmitters).
• Traffic lights with flashing option.
• The function of shortening the auto-closing time after detecting a passage - PHOTO CLOSE.
• Support for NC and NO limit switches.
• Possi ility to install an infrared arrier.

• Simple installation and programming procedure.
MODE OF ACTION
The drive is controlled y the transmitter utton programmed in HELB11 or the SBS
sequence control ell utton. In the case of control from the SBS input or a transmitter assigned to
this function, the operation consists in carrying out the step- y-step commands OPEN-STOP-
CLOSE-STOP or with the ONLY OPEN function ena led, it is only possi le to open the gate. After
turning on the power, the first command is to open, if we give the next command while the gate is
moving, we will stop it, and then we can run it in the closing direction. The WICKET function
(partial opening) is controlled y a utton on the transmitter assigned to this function.
De ending on the version, the controller works with motors with or without a built-in
ulser. For the version with the ulse generator, it is also ossible to disable its su ort during
the engine o eration rogramming rocedure. The lighting of the ENCODER diode means that
the o eration is switched on.
ATTENTION!
The ulser arameters must be consistent with the descri tion in aragra h SOFTWARE for the
a ro riate version of the controller.
DRIVER INSTALLATION
Before starting the installation, make sure that all safety
recommendations are met.
Any installation work may only be erformed by qualified ersonnel.
Electrical installation and connection of electronic devices may only be
erformed by ersons with a ro riate electrical qualifications.
1. Turn off the ower.
2. Install the controller mechanically.
3. Pull out the quick cou lings.
4. Connect the cables to the quick cou lers according to the descri tion or connection diagram:
(wires connected to quick cou lers should be flexible - "cord")
1.1. Connecting the limit switch for o ening and closing
The limit switch for opening and closing is used to precisely stop the gate in the closed or open
position. Adjust the position of the magnets so that the gate opens and closes accurately.
16 OL —opening limit
17 CL — closing limit switch,
18 COM — common cord
The controller works with the normally open NO or normally closed NC type limit switches. The
selection is made with the NC / NO switch.
NC/NO from position ON –normally open NO
NC/NO in position OFF –normally closed NC
1.2. Connecting hotocells
The infrared arrier is an essential security element that must e connected to the
controller. It prevents the gate from hitting a vehicle, person or o ject in its light. Photocells are

necessary for the correct operation of the device and ensure safety. If the encoder support is
disa led, it is required to connect a safety curtain or other additional protection against crushing
in the gate's light. They must e connected in series with the photocells
.
PHOTOCELL
12 +24VDC – photocells power supply plus
13 COM –photocells power supply minus
13 COM –COM output of the photocell
14 FOTO –NC contact of the photocell
The power supply of the 24V connector is <450mA, therefore make sure
that the total power load does not exceed this current value An exemplary
photocell connection diagram is shown in fig 2
1.3. Connection of the manual control
Connection of the manual control should e made with a 2x 0.5mm ca le (the ca le type
should e in accordance with CEI 20-22; CEI EN50267-2-1 standards), the maximum length of the
manual control ca le depends on its electrical parameters, therefore it should e assumed the
following rule that with the required ca le length, its resistance should not exceed 100ohm. As a
standard, the use of a ca le with a cross-section of 0.5 mm and a length of not more than 20 m is
sufficient for the correct operation of the controller, for required greater distances, 4x0.5 (mm)
ca les can e used y connecting the wires in parallel - in pairs, or y increasing the cross-section
of the ca le (2x 1mm).
15 SBS – ell utton
18 COM
1.4. Pulse generator connection - OPTIONAL
The controller supporting the pulser located on the engine has an ENCODER connector. The
installation consists in connecting the wires to this connector.
Next, make the electrical connections of the connector on the left side as shown
in Fig 2
1.5. Ca acitor connection
Connect a capacitor to connector num ers 9 and 10, polarity does not matter.
1.6. Motor connection
The motor connection should e made in accordance with the description:
7 COM – common engine wire
11 OPEN – motor ca le to activate it in the direction of opening
8 CLOSE – motor ca le to actuate it in the closing direction
1 PE – PE protective conductor
1.7. Connection of signal lighting
The light ul with a power not exceeding 15W / 230V should e connected to connectors 5 and 6:
5 – the neutral wire of the lamp
6 – lamp phase wire
When using the flashing light function, do not connect the signaling
device with the built-in internal circuit breaker This can damage the driver
When using a signaling device with a built-in circuit breaker, make sure that the
light function is set to continuous mode before connecting it
Fluorescent lamps must not be used as traffic lights
1.8. Power connection

The last stage of connection is to connect the controller power supply. Connect in turn the
wires:
2 PE –protective conductor
3 L –phase wire
4 N –neutral wire
Protect the controller power supply by using a residual current circuit
breaker
2. Put the quick cou lers back into the controller.
Before starting the device, check the power supply, grounding and
wiring The cables should not be too long, it is not allowed to wind the
remaining cable in the so-called "Loops" The controller power, motor and
control cables should be kept separate
3. Manually lace the gate in the center.
4. Turn on the ower.
5. Program the remote-control transmitters.
6. Check the o ening direction.
The first pressing of the manual control utton or the transmitter (which has een
programmed) starts the door in the opening direction. Otherwise, swap the wires connected to
the OPEN (11) and CLOSE (8) connectors (after disconnecting the power supply first).
7. Set otentiometer VR1 (turning clockwise increases the value, on the contrary reduces it) the
engine's thrust (selected for the load in accordance with the a licable standards).
The regulation should be carried out in accordance with the applicable
standards
8. Program the remote control transmitters.
9. Program the engine o eration - according to the rocedure described in aragra h Programming.
10. For the motor with the ulse generator, adjust the sensitivity of overload detection with the VR2
otentiometer.
The regulation should be carried out in accordance with the applicable
standards
11. Check the correct o eration of the entire automatic unit and all connected safety, signaling and
control elements (limit switches, hotocell, edge stri , light signaling etc.).
12. Set the available additional functions.
13. Train all users of the gate.
CONNECTION DIAGRAM

SETTING PROGRAMMING
Programming the controller is done using the SETUP, LEARN uttons, LED and ENCODER
diodes and 4 function switches located on the controller oard.
Programming can only take lace when the gate is in sto state. If we start rogramming
the controller during the auto-closing time countdown, the countdown will be sto ed and to
close the gate, ress the SBS button or the remote-control transmitter.
TRAFFIC LIGHTS
While the gate is moving, the traffic lights can work in two modes: continuous light and flashing (slowly
when the gate opens, and quickly when the gate closes). In addition, it can act as an auxiliary lighting
for a driveway or garage with delayed switch-off.
Programming should be performed with the AUTO CL switch turned off
SETTING THE LIGHT OFF DELAY
We set it in the range from 0s to 25min with a step of 15s. Default: 0s
If the AUTO CLOSE function is ena led, set the
AUTO CL switch to the OFF position.
Hold down the SETUP utton for less than 3s.
When the utton is pressed, the LED lights up.
Release the SETUP utton.
The LED will flash rapidly.
Within 5s, start setting the time.
Press SETUP x times. One press corresponds to
15s. Each pressing is signaled y the lighting of the
diode. If the utton is not pressed within these 5s,
the controller will set the time to 0s.
After 3s from the last press, the LED will flash 3
times. The controller will remem er the settings
and return to normal operation.
Set the AUTO CL switch to the desired position.
FLASHING ON / OFF (Default: enabled)
If the AUTO CLOSE function is ena led, set the
AUTO CL switch to the OFF position.
Hold down the SETUP utton for less than 3s.
When the utton is pressed, the LED lights up.
Release the SETUP utton.
The LED will flash rapidly.