Haugen MIJ-SKD User manual

Marv Haugen Enterprises
1851 Heartland Ave.
Casselton, ND 58012
Toll Free 877-580-6218
Phone: [phone] Fax: [phone]
DOC# MIJ-SKD-M
Skid-Steer Industrial Jib
Model #MIJ-SKD
Operator’s Installation
and
Safety Manual
Marv Haugen Enterprises Inc. * 1851 Heartland Ave. * Casselton ND 58012 * Phone: [phone]
www.haugenattachments.com

MIJ-SKD - Industrial Jib
Haugen Skid-Steer Industrial Jibs are designed for use on Skid-Steer loaders and other machines
equipped with the skidsteer mount. The MIJ-SKD has been engineered and rated for the Load Capaci-
ties as shown on the load chart decal on the Jib and in the load chart in this Manual.
Installation of the Skid-Steer Jib
Using your Skidsteer loader align the quick attach plate with the attachments plate and couiple into the
attachment. Before lifting make sure that the skidsteer copuipler pins are through each hole and the
top bar is secured. Always check these pins during operation. Hydraulic or manual coupler pins can
move over time.
Thank you for choosing a Haugen Skid-Steer Industrial Jib
Engineering Certication
The MIJ-SKD has been tested and certied by a third party Certied Professional Engineer. A copy
of the certication letter is included in this manual. If required a copy of the full engineering report is
available upon request.
Before you use this Jib you must read and understand the Operator’s Manual
If you have questions call us at 1-877-580-6218
Marv Haugen Enterprises
1851 Heartland Ave.
Casselton, ND 58012
Toll Free 877-580-6218
Phone: [phone] Fax: [phone]
- Operating Rules for Industrial Jibs -
Inspection
1. Check the lift hook, Latch and Shackle making sure that it is properly installed and in good
working condition.
2. Quick atrtach should be in good shape and installed correctly.
3. Check the Industrial Jib for any excessive wear, cracked or broken welds.
4. Check each of the lifting holes for any elongation.
5. The Industrial Jibs load chart must be present and legable.

Marv Haugen Enterprises
1851 Heartland Ave.
Casselton, ND 58012
Toll Free 877-580-6218
Phone: [phone] Fax: [phone]
General Operating Rules
1. Inspections as stated above must be made prior to each use of the Industrial Jib
2. Before each use make sure the Jib is properly installed and the hook and shackle are secured to the
Jib and the screw pin is tight.
3. Check extension adjustment pin to make sure it is functioning properly and secured in the desired
position.
4. Determine that the load your lifting is within the capabilities of the Industrial Jib and the capacity
of the Skid-Steer. Never exceed the capacities on either the Skid-Steer or the attachment, Remember
that capacity of the Host machine decreases when the load is raised and extended
5. The machine operator must remain in the seat at the controls with the engine running whenever there
is a load on the Jib.
6. Only qualied and trained personal should operate the host machine. Operators should know and
follow all local, state and federal safety regulations
7 All safety regulations must be followed at all times.
8. Any personal working around the Jib must wear hard hats and steel toed boots
9. When lifting loads there should be no personel within a minimum of ten feet in all directions of the
fall zone, never put yourself or any part of your body under a suspened load.
10. Operator must not be under the inuence of any alcohol or drugs.
11. Do not pull loads. The Jib is designed for vertical lifting ONLY.
12. Carry all loads low and use tag lines to keep loads from swinging.
13. Be sure the host machine is on a level /rm surface before raising the load.
14. Do not use the Jib in anyway to lift personal.
15. Refer to the host machines operators manual for more information on handling elevated loads and
additional safety tips.
- Operating Rules for Industrial Jibs continued -

Model # MIJ-SKD
7 Hook Positons ranging from 27.75” to 97.25”
Empty Weight = 380 LBS
Vertical Center of Gravity = 1.83” from the top plate
Horizontal Center of Gravity - See chart below
Hook Position Horizontal Center Of Gravity Distance
1 24.25” 27.75”
2 24.32” 39.75”
3 24.45” 51.75”
4 24.62” 63.25”
5 25.75” 75.25”
6 26.72” 87.25”
7 27.12” 97.25”
Marv Haugen Enterprises
1851 Heartland Ave.
Casselton, ND 58012
Toll Free 877-580-6218
Phone: [phone] Fax: [phone]
Marv Haugen Enterprises Inc. * 1851 Heartland Ave. * Casselton ND 58012 * Phone: [phone]

(Copy of the Load Chart Decal)
Marv Haugen Enterprises
1851 Heartland Ave.
Casselton, ND 58012
Toll Free 877-580-6218
Phone: [phone] Fax: [phone]
Jib Load Capacity
The lift capacities for the various positions shown in the table below are for our Model (MIJ-SKD)
Industrial Jib. Note: This chart reects the capacity of the Jib only and does not reect the
capacity of the host machine nor the maximum load that can be safely handled by a particular
machine
Marv Haugen Enterprises Inc. * 1851 Heartland Ave. * Casselton ND 58012 * Phone: [phone]
Multiple Hooks
The MIJ-SKD is furnished with a hook and shackle system that can be moved easily to various po-
sitions on the Jib as needed. The Hook is rated for a 6000 lbs capacity. More than one hook can be
used but the lift capacity would be limited by most extended hook. For example if the most extended
hook is in the eight position then the load must not exceed 2000 lbs.
Note:
The information, load charts and illustrations contained in this manual about the Haugen Industrial
Jib were current at the time of publication. Haugen Attachments is continuely updating and improv-
ing our products. Therefore Haugen reserves the right to redesign this attachment and update the
operators manual at any time without notice.
WARNING
*Lift Capacity Rating
1
2
3
4
5
6
7
Jib Position
27.75 inches
39.75 inches
51.75 inches
63.25 inches
75.25 inches
87.25 inches
97.25 inches
5000 LBS
4500 LBS
4000 LBS
3450 LBS
2900 LBS
2450 LBS
2000 LBS
Length *Max Lift Capacity
* These lift capacity ratings are for the Industrial Jib only. The lifting capacity is ultimately deter-
mined by the host machine. Never lift more than the operating capacities of this Industrial Jib or
the capacities stated by the Manufacturer of the host machine. MIJ-SKD
Empty Weight - 380 lbs

Marv Haugen Enterprises warrants it’s products , under normal use and maintenance, to be free from defects in
material and workmanship for a period of one year from the purchase date from an authorized Haugen Dealer.
e limited warranty is extended only to the original purchaser of Haugen ProductsWarranty Statement
1. During the applicable warranty period, Haugen at it’s option , will repair or replace any part determined
by Haugen to be defective. Such repair or replacement shall take place at Haugen’s factory or a
location designated by Haugen. Under no circumstances shall Haugen be obligated for the cost of any
repair or replacement by anyone other than Haugen without its express written consent.
2. Parts may not be returned without the express written authorization from Haugen.
3. Some purchased components including but not limited to hooks, cylinders, and hydraulic motors are
subject to inspection and warranty of the respective manufacturers.
4. is warranty is void if any attempt is made to make eld repairs. Make sure to leave the product in its
original failed condition.
5. To make a claim under this warranty rst contact your authorized Haugen dealer. e Haugen dealer
shall complete the warranty claim form and obtain written authorization from Haugen to return parts.
All warranty claims must include detailed information regarding make and model of the vehicle on which
the Haugen product was mounted, hours of use, description of events that led up to the failure, and any
other information helpful in reviewing this claim. All warranty returns must be prepaid. Shipments
arriving at our factory on a freight collect basis will be refused by our recieving department. e freight
charges will be credited if the parts are determined by haugen to be defective, and the associated freight
costs in returning those parts will be prepaid by Haugen.
6. Products or parts thereof which, as determined by Haugen’s examination, show wear from normal use,
been improperly operated, damaged by accident or negligence, eld repaired, altered or modied are
not considered defective in material or workmanship and are not covvered by this warranty. is
warranty does not obligate Haugen to bear any cost of labor for eld repair, replacement, testing, or
adjustment nor damaged caused by accident, abuse, misuse, or environmental elements.
7. Any parts or labor required to repair or replace parts not covered under this warranty will be charged to
the customer. Parts repaired or replaced by Haugen are then covered by this warranty only for the
remainder of the original warranty as if such parts were original parts.
8.. Haugen reserves the right to change its specications and designs at any time.
is warranty is exclusive and in lieu of all other express warranties, if any including implied warranties of
merchantability and tness for a particular purpose. It shall not extend beyond the duration of the expressed
warranty provided herein and the remedy for violations of any implied warranty shall be limited to repair or
replacement of the defective part pursuant to the terms contained herein. No employee, dealer, salesman,or
representative is authorized to change this warranty in any way or grant any other warranty. Haugen shall not
be liable for any consequential, incidental, or punitive damages, losses or expenses, including those resulting
from or caused by any defects.
Marv Haugen Enterprises
1851 Heartland Ave. - Casselton, ND 58012
Toll Free 877-580-6218
Phone: [phone] Fax: [phone]
Warranty Statement

Warranty Statement
Marv Haugen Enterprises Inc. * 1851 Heartland Ave. * Casselton ND 58012 * Phone: [phone]
www.haugenattachments.com