Zico QUIC-RELEASE QR-CL-H Parts list manual

ZICO®
3030PM19
QUIC-RELEASE®HoRIzontAL CyLIndER LIft
ModEL QR-CL-H
PARtS And InStRUCtIon MAnUAL
The Zico Horizontal Cylinder Lift raises and lowers "M" through
"J" cylinders. Unit has a maximum lifting capacity of 200 lbs.,
and a maximum lift height of 47".
The unit operates off of a supplied 12v battery.
A charger is provided with the unit.
MODEL DESCRIPTION WT./@ IN LBS.
QR-CL-H Complete System 165.0
Rev. 9-9-15

Page 2

Page 3
1A
1B
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
19A
20
21
22
23
24
25
26
27
28
29
30
31
32
33
3030-250-101
3030-250-102
3030-250-103
3030-250-105
3030-250-107
3030-250-163
3030-250-111
3098-105-113
3030-250-113
3030-255-905
3030-255-105
3030-255-159
3030-255-161
3030-250-185
3030-250-183
3030-250-157
3030-250-129
3030-250-131
3030-250-159
3030-255-905
3030-255-109
3030-250-137
9018-105088
9015-103728
9015-103764
9015-103788
9018-175001
9015-103732
9013-173700
9014-113700
9014-203700
3030-255-151
9010-562512
9010-102516
9014-112500
Leg, Left
Leg, Right
Main Upright
Tie Rod
Forward Brace
Threaded Spacer
Lifting Arms
Actuator
Handle
Rack Assembly
Foot Assembly
Handle
Foot Tube Spring
Swivel Casters (Hard Rubber)
Swivel Casters W/Brakes (Hard
Rubber)
Spacer, Actuator, Short
Spacer, 1.5 OD x 1.125 ID x 5 LG, AL
Spacer, 1.5 OD x 1.125 ID x 4 LG, AL
Spacer, Actuator, Long
Hub Assembly
Tray Lock Handle
Bushing, Pivot, .744 OD x 385 ID x
.390 LG.
Screw, 1/2ø x 5.5, HH, GR. 8
Screw, 3/8ø-16 x 1 3/4, HH
Screw, 3/8-16 x 4, HH
Screw, 3/8-16 x 5 1/2, HH
Nut, 1/2-13 Hex Nylock Low Prole
Screw, 3/8-16 x 2, HH
Nut, 3/8-16 Nylock
Flatwasher, 3/8ø NOM
Lockwasher, 3/8ø
Foot Stop
1/4-20 x 1" Rnd Torx Head Bolt
Screw, 1/4-20 x 1 HH
Flatwasher, 1/4ø
1
1
1
1
2
2
4
1
1
1
1
1
1
2
2
1
2
3
3
1
1
12
2
6
2
5
1
4
15
30
6
1
1
20
43
ITEM
NO. PART NO. DESCRIPTION QTY.
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
9015-172500
3030-255-111
9014-202500
3030-255-121
3097-105-145
3030-250-165
3097-105-146
3097-105-144
9015-103720
3030-250-155
3030-250-161
3030-250-145
9010-102560
3030-255-125
3030-255-155
9040-102528
3030-255-157
3030-255-101
3087-207-105
3030-255-123
9014-115000
3030-250-139
3030-250-141
9012-105000
9013-175000
9010-313112
9013-172501
3097-105-216
3030-250-167
3030-250-173
3030-250-175
3030-250-177
3030-250-171
3030-250-179
3030-250-181
9013-173100
9014-113100
Nut, 1/4-20 Nylon Lock
Horizontal Cart Main Shaft
Lockwasher, 1/4ø Split
Horizontal Cart Bearing
Boot, Switch
Strain relief
Washer, Switch Anti-Rot.
Switch, Toggle, DPDT, MOM
Screw, 3/8-16 x 1 1/4 HH, Gr. 5
Cord Assembly, Electrical
Battery Holder
Battery 12 V 85CCA
Screw, 1/4-20 x 3 3/4 Lg., HH
Horizontal Cart Front Rail
1" Shaft Snap Ring, .045 Thk.
Spring Pin .25 X 1.75
1/2" Shaft Sleeve Bearing
Foot Tube Spacer
Strap Assembly
Base Post Split Collar
Flatwasher, 1/2 I.D. SZP
Endp, Plastic, 2 x 3
End Cap, Plastic, 2 x 4
Nut, 1/2-13, Jam
Nut, 1/2-13, Hex Nylock
5/16 x 3/4 Hex Socket Hd. Shoulder Blt.
Nut, 1/4-20 Nylock Low Prole
4 x 2 Wear Pad
Model Number Tag
QR-CL Caution Label
QR-CL Hand Pinch Warning Label
QR-CL Warning Label
12V 1/2 Amp (500MA) Trickle Charger
Edge Protector 4" Lg.
Edge Protector 2 1/2" Lg.
Nut, 5/16, 18 Nylock
Flatwasher, 5/16ø NOM.
18
1
1
2
1
1
1
1
2
1
2
1
2
2
1
1
3
1
1
1
2
4
1
1
1
1
1
3
1
1
1
2
1
2
2
1
2
ITEM
NO. PART NO. DESCRIPTION QTY.

Page 4
WARNING: When moving the QR-CL-H with a cylinder, move the unit slowly with the cylinder in a
vertical position. Have the bottom of the cylinder as close to the oor as possible to avoid tipping over.
WARNING: QR-CL-H should always be stored with the RackAssembly (9) in the upright/vertical
position and the Footplate (10) rmly against the oor. Do not leave QR-CL-H in a raised or horizontal
position unattended. A tip over situation may occur.
Numbers in parentheses refer to numbers in parts breakdown (see pages 2 & 3)
Battery Installation
Note: Battery must be charged 5-8 hours before rst use. Do not exceed more than a 24 hour charge.
1. Place Battery (45) into the Battery Holder (44).
2. Attach red wire to the positive terminal and the black wire to the negative terminal.
3. QR-CL-H is now ready to operate. Please read the rest of the manual before rst use.
Removing the empty cylinder from the vehicle compartment
1. Remove the oxygen line and apply the safety cap to cylinder. Remove all vehicle straps or brackets holding
the horizontal cylinder in place.
2. Press the QR-CL-H switch (41) to raise Rack Assembly (9) high enough to clear Legs (1) when Rack
Assembly is rotated.

Page 5
3. Pull the Lock Handle (19A) and manually rotate Rack Assembly until it locks into the horizontal position.
4. Move QR-CL-H into position next to the vehicle. Raise Rack Assembly to the proper height to align with
cylinder compartment. Activate wheel locks.
5. Rotate Footplate Handle (11) until Footplate (10) is clear and cylinder can be slid onto Rack Assembly.
NOTE: The valve-end of the cylinder must be facing the handle end of the RackAssembly.
6. Slide empty cylinder into Rack Assembly until it clears the Footplate. Release Footplate Handle and
conrm cylinder is ush with footplate. Strap cylinder in and buckle. Tighten strap.
7. Position Rack Assembly high enough that it will not hit legs when rotated to a vertical position. When
ready, unlock Rack Assembly with Lock Handle and rotate until it locks in the vertical position.
Footplate fully opened Valve toward handle end

Page 6
Loading a cylinder onto the QR-CL-H
1. Position Rack Assembly (9) and Footplate (10) at the end of cylinder to be loaded. Angle cylinder enough
to slide Footplate underneath.
2. Activate wheel locks, then buckle cylinder in place. Tighten straps to secure.
3. Raise the cylinder slightly off the ground. Release wheel locks. Carefully move the QR-CL-H with the
cylinder to the vehicle.
Placing a full cylinder in the vehicle
1. Press the QR-CL-H switch (41) to raise Rack Assembly (9) high enough to clear Legs (1) when Rack
Assembly is rotated.
2. Pull the Lock Handle (19A) and manually rotate Rack Assembly until it locks into the horizontal position.
3. Move QR-CL-H into position next to the vehicle. Raise Rack Assembly to the proper height to align with
cylinder compartment. Activate wheel locks.
4. Loosen strap and unbuckle cylinder.
5. Rotate Footplate Handle (11) until Footplate (10) is clear and cylinder can be slid into compartment.
6. Remove safety cap. Slide full cylinder into compartment and secure. Attach oxygen line.

Ziamatic Corp.
10 West College Avenue, P.O. Box 337, Yardley, PA 19067-0587 • [phone] • FAX: [phone]
*ZICO is a registered trademark for re, safety and marine products made by Ziamatic Corp.Copyright Ziamatic Corp. 9-15
www.ziamatic.com
TOLL FREE: 800-711-3473
Page 7