Hawking HNC320W User manual

1

Trademarks & Copyright
Windows 95/98/ME and Windows NT/2000/XP are registered trademarks of Microsoft Corp. All other brands and product names are
trademarks of their respective companies.
No part of this publication may be reproduced in any form or by any means or used to make any derivative (such as translation,
transformation or adaptation) without the express written consent of the manufacturer as stipulated by the United States Copyright Act
of 1976.
FCC Certifications
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
x Reorient or relocate the receiving antenna.
x Increase the separation between the equipment and receiver.
x Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
x Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission limits.
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your
authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired
operation.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be
required to take adequate measures.
All trademarks and brand names are the property of their respective proprietors.
Specifications are subject to change without prior notification.
2

HAWKING LIMITED WARRANTY
Hawking Technology guarantees that every HNC300 Network Camera and every HNC320W Wireless Network
Camera is free from physical defects in material and workmanship under normal use for (1) year from the date of
purchase. If the product proves defective during this one-year warranty period, call Hawking Customer Service in
order to obtain a Return Authorization number. Warranty is for repair or replacement only. Hawking
Technology does not issue any refunds. BE SURE TO HAVE YOUR PROOF OF PURCHASE. RETURN
REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. When returning a product, mark
the Return Authorization number clearly on the outside of the package and include your original proof of
purchase.
IN NO EVENT SHALL HAWKING TECHNOLOGY’S LIABILTY EXCEED THE PRICE PAID FOR THE PRODUCT
FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE
USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE OR ITS DOCUMENTATION. Hawking Technology makes
no warranty or representation, expressed, implied or statutory, with respect to its products or the contents or use of this
documentation and all accompanying software, and specifically disclaims its quality, performance, merchantability, or fitness
for any particular purpose. Hawking Technology reserves the right to revise or update its products, software, or
documentation without obligation to notify any individual or entity. Please direct all inquiries to:
[email protected].
3

About This User’s Manual 6
Introduction 7
System Requirements 8
Features and Benefits 9
Physical Description 10
HNC300
Front Panel 10
Power LED 10
Link LED 10
Rear Panel 11
Network Cable Connector 11
DC Power Connector 11
Reset Button 11
Top Panel 12
Screw Hole 12
Bottom Panel 12
Screw Hole 12
HNC320W
Front Panel 13
Power LED 13
Link LED 13
Rear Panel 14
Network Cable Connector 14
DC Power Connector 14
Reset Button 14
Antenna Connector 14
Top Panel 15
Screw Hole 15
Bottom Panel 15
ScrewHole 15
Unpacking the Camera 16
Hardware Installation 17
HNC300
Connect an Ethernet Cable 17
Attach the External Power Supply 17
HNC320W
Attach Wireless Antenna 18
Connect an Ethernet Cable 18
Attach the External Power Adapter 19
Security 20
Software Installation 21
Web Configuration 21
Main Menu Page 21
4

System Administration 22
System: HNC300 22
HNC320W 27
Image 32
Users 33
Date/Time 34
Email (HNC320W Only) 36
Upload 36
Information 38
Tools 39
View Image – ActiveX Mode 40
View Image – Java Mode 41
Camera Applications 42
Applications 42
Home Applications 42
SOHO (Small Office, Home Office) Applications 43
IPView SE Application Installation 44
IPView SE – Getting Started 49
IPView SE Control Panel 49
How to Add Camera 50
How to Change Cameras 53
How to Connect/Disconnect the Image 54
How to Delete a Camera 55
Extera Information 56
How to Adjust the Property Setting 56
How to Adjust the Recording Setting 60
Appendix 61
A. Frequently Asked Questions 61
B. Ping Your IP Address 62
C. Troubleshooting 62
D. Upgrade Firmware 64
E. Time Zone Table 65
F. Xplug Control Installation 66
G. Adjusting the Camera Focus 69
H. Specifications: HNC300 70
HNC320W 72
I. How to View Your Camera via the Internet 74
J. Glossary of Terms 79
5

This user’s manual gives a full explanation of the HNC300 (Wired) Network Camera and HNC320W Wireless Network
Camera, including a description of features, installation procedures, web configuration, and other functions. Also
included in the user’s manual are the operating procedures for the IPView SE application.
6

Thank you for purchasing either the HNC300 Network Camera or the HNC320W Wireless Network Camera. The
HNC300 connects directly to an Ethernet or Fast Ethernet network. The HNC320W can also connect directly to an
Ethernet or Fast Ethernet network, but also supports the IEEE 802.11b wireless standard. The HNC300 Series (the
collective title for the HNC300 & HNC320W models) network cameras are different from conventional PC cameras in
that they are standalone systems with built-in CPUs and web servers. Therefore, they connect directly to the local area
network (LAN) and do not need to be connected to a designated PC. Thus, they provide a low cost solution that can
transmit high quality video images for monitoring and surveillance. The network cameras can be managed remotely, and
can be accessed and controlled from any PC/Notebook over the LAN or Internet using only a web browser. The simple
installation procedures and web-based interface offer easy integration to your network application environments.
7

HNC300 & HNC320W
Network:
Local Area Network (HNC300 & HNC320W): 10Base-T Ethernet or 100Base TX Fast Ethernet
Wireless Local Area Network (HNC320W): IEEE 802.11b Wireless LAN
\
Recommended PC or Notebook to Access the HNC300 & HNC320W:
System requirements:
CPU: Pentium II, 266 MHz or above
Memory Size: 32 MB (64 MB recommended)
VGA card resolution: 800x600 or above
Web Browser:
x Internet Explorer 5.0 or above (ActiveX & JAVA Mode – Image View for Windows OS and JAVA Mode –
Image View for other OS)
x Netscape 6.0 or above (JAVA Mode – Image View)
IPView SE Application:
x Supported Operating Systems: Win 98 SE, Win 2000, Win Me, Win XP
x System requirements for IPView SE:
CPU: Pentium III, 450 MHz or above
Memory Size: 128 MB (256 MB recommended)
VGA card resolution: 800x600 or above
8

This section describes the features and benefits of the HNC300 Network Camera & HNC320W Wireless Network
Camera.
Simple to Use
The HNC300 and HNC320W are standalone systems with built-in CPUs, and thus, require no special hardware or
software such as PC frame grabber cards. The HNC300 and HNC320W support both ActiveX mode for Internet Explorer
and Java mode for Internet Explorer and Netscape Navigator. Therefore, all that is required is web browser software such
as Internet Explorer 5.0 or above, or Netscape 6.0 or above. All you need is a valid IP address to view the picture from
your network camera.
Supports a Variety of Platforms
The HNC300 & HNC320W both support TCP/IP networking, SMTP e-mail, HTTP and other Internet related protocols.
Both models can be utilized in mixed operating system environments such as Windows, Unix, and Mac. They can easily
be integrated into other Internet/Intranet applications.
Web Configuration
Using a standard web browser, the administrator can configure and manage the HNC300 or HNC320W directly from its
own web page via the web.
HNC300
The administrator can set up to 8 usernames and passwords via the privilege settings.
HNC320W
The administrator can set up to 64 usernames and passwords via the privilege settings.
Remote Utility
The powerful IPView SE application assigns the administrator a pre-defined user ID and password through which, he/she
can modify the HNC300/HNC320W settings from a remote site via the Intranet or Internet. For added convenience, when
new firmware becomes available, the administrator can also upgrade remotely over the network. Users are also allowed
to monitor the images and take snapshots.
Broad Range of Applications
Using today’s high-speed Internet services, the HNC300/HNC320W network cameras can provide an ideal high
performance, cost-effective solution that delivers live video images over the Intranet and Internet for remote monitoring
and surveillance. The network cameras allow remote access from a web browser for live image viewing. They also allow
administrators to manage and control the network cameras anytime from anywhere in the world. You can set up the
network cameras to monitor various objects and locations such as homes, offices, banks, hospitals, child-care centers,
amusement parks and a variety of other industrial and public areas. The network cameras can also be used for intruder
detection, still image capture for archiving, and many other applications.
9

HNC300
This section describes the externally visible features of the HNC300.
Front Panel
Link LED
Power LED
Power LED
The “Power” LED is located to the right of the camera’s lens (when facing the camera). A steady blue light confirms that
the camera is powered on.
Note:
The “Power” LED has three settings with which to control the light illumination while monitoring: Normal / Off /
Dummy. Please refer to the “Web Configuration” section for detailed information and usage.
Link LED
The “Link” LED is located on the far right side of the network camera’s lens (when facing the network camera). It is
located to the right of the “Power” LED. A steady orange light confirms a good connection. Depending on the data
traffic, the LED will begin to flash to indicate that the camera is receiving/transmitting from/to the network.
Note:
The “Link” LED has three settings with which to control the light illumination while monitoring: Normal / Off /
Dummy. Please refer to the “Web Configuration” section for detailed information and usage.
10

Rear Panel
Ethernet Cable
Port
Reset Button
10/100 Ethernet
DC 5V
Reset
DC Power
Connector
Network Cable Connector
The rear panel of the network camera features an RJ-45 connector for 10Base-T Ethernet or 100Base-TX Fast Ethernet
connections (using Category 5 twisted-pair cabling). The port supports the N-Way protocol, thereby allowing the network
camera to automatically detect or negotiate the transmission speed of the network.
DC Power Connector
The DC power input connector is located on the rear panel of the network camera and is labeled DC 5V with a single jack
socket to supply power to the camera. Power will be generated when the power supply is connected to a wall outlet.
Reset Button
Reset will be initiated when the reset button is pressed once and the “Power” LED begins to flash.
Factory Reset will be initiated when the reset button is pressed continuously for at least three seconds or when the “Power
LED” begins to light up. Release the reset button and the “Power” LED will begin to flash, indicating that the network
camera is utilizing the factory reset. When factory reset is completed, the IP address will return to the default setting of
192.168.0.20.
11

Top Panel
Screw Hole
Located on the top panel of the network camera, the screw hole is used to connect the camera stand onto the camera by
attaching the screw head on the camera stand into the screw hole of the camera.
Bottom Panel
Screw Hole
Screw Hole
Located on the bottom panel of the network camera, the screw hole is used to connect the camera stand onto the camera
by attaching the screw head on the camera stand into the screw hole of the camera.
12

HNC320W
This section describes the externally visible features of the HNC320W.
Front Panel
Link LED
Power LED
Power LED
The “Power” LED is located to the right of the camera’s lens (when facing the camera). A steady blue light confirms that
the camera is powered on.
Note:
The “Power” LED has three settings with which to control the light illumination while monitoring: Normal / Off /
Dummy. Please refer to the “Web Configuration” section for detailed information and usage.
Link LED
The “Link” LED is located on the far right side of the network camera’s lens (when facing the wireless network camera).
It is located to the right of the “Power” LED. A steady orange light confirms a good connection. Depending on the data
traffic, the LED will begin to flash to indicate that the camera is receiving/transmitting from/to the network.
Note:
The “Link” LED has three settings with which to control the light illumination while monitoring: Normal / Off /
Dummy. Please refer to the “Web Configuration” section for detailed information and usage.
13

Rear Panel
Network Cable
Connector
DC Power
Connector
Reset Button
Antenna
Connector
10/100 Ethernet
DC 5V
Reset
ANT
Network Cable Connector
The rear panel of the wireless network camera features an RJ-45 connector for 10Base-T Ethernet or 100Base-TX Fast
Ethernet connections (using Category 5 twisted-pair cabling). The port supports the N-Way protocol, thereby allowing
the wireless network camera to automatically detect or negotiate the transmission speed of the network.
DC Power Connector
The DC power input connector is located on the rear panel of the wireless network camera and is labeled DC 5V with a
single jack socket to supply power to the camera. Power will be generated when the power supply is connected to a wall
outlet.
Reset Button
Reset will be initiated when the reset button is pressed once and the “Power” LED begins to flash.
Factory Reset will be initiated when the reset button is pressed continuously for at least three seconds or when the
“Power” LED begins to light up. Release the reset button and the “Power” LED will begin to flash, indicating that the
wireless network camera is utilizing the factory reset. When factory reset is completed the wireless camera will be set to
Channel 11 by default and the ESS-ID is set as “NULL String”. (This default setting will let the wireless camera
connect to ANY access point on the infrastructure network). The IP address will also return to the default setting of
192.168.0.20.
Antenna Connector
There are two SMA-type antenna connectors located on the rear panel of the wireless camera, thereby providing
connection for two, high sensitivity antennas that are included with the device.
14

Top Panel
Screw Hole
Screw Hole
Located on the top panel of the wireless camera, the screw hole is used to connect the camera stand onto the camera by
attaching the screw head on the camera stand into the screw hole of the wireless camera.
Bottom Panel
Screw Hole
Screw Hole
Located on the bottom panel of the wireless camera, the screw hole is used to connect the camera stand onto the camera
by attaching the screw head on the camera stand into the screw hole of the wireless camera.
15

Unpack and Inspect
Open the package and carefully remove all items.
The complete HNC300 package consists of:
x One HNC300 (Wired) Network Camera
x One Installation CD-ROM
x One Quick Installation Guide
x One DC power adapter
x One Camera Stand
x One RJ-45 Ethernet Cable
The complete HNC320W package consists of:
x One HNC320W Wireless Network Camera
x One External Wireless Antenna
x One Installation CD-ROM
x One Quick Installation Guide
x One DC power adapter
x One Camera Stand
x One RJ-45 Ethernet Cable
Please check to make sure that the unit was not damaged during shipping and that no items are missing. If you encounter a
problem, please contact your dealer.
Please read this manual thoroughly, and follow the installation and operation procedures contained within.
Connecting the HNC300/HNC320W to the Camera Stand
The HNC300 and HNC320W packages include a camera stand (installation is optional) with a swivel ball screw head that
can be attached to the camera’s screw holes. Attach the camera stand to the camera and orient it in the most appropriate
position for your specific application. In addition, there are three holes located on the base of the camera stand, thereby
allowing the camera to be securely mounted on the ceiling or wall.
16

This section describes the hardware installation procedures for the HNC300 and HNC320W.
HNC300
Connect an Ethernet Cable
Connect an Ethernet cable to the Ethernet cable port located on the rear panel of the camera, and attach the other end to
the network.
10/1 00 Ether net
DC 5V
Reset
Attach the External Power Supply
Attach the external power supply to the DC power input connector located on the rear panel of the camera. The input
connector is labeled “DC 5V”. Connect it to your local power supply.
10/1 00 Eth ernet
DC 5V
Reset
Note:
Confirm that the device is receiving power by making sure that the “Power” LED is illuminated.
17

HNC320W
Attach Wireless Antenna
On the rear panel of the wireless camera, screw into the antenna connector the single external antenna that was included in
the product packaging.
Connect an Ethernet Cable
Connect an Ethernet cable to the Ethernet cable port located on the rear panel of the camera, and attach the other end to
the network.
18

Attach the External Power Supply
Attach the external power supply to the DC power input connector located on the rear panel of the camera. The input
connector is labeled “DC 5V”. Connect it to your local power supply.
Note:
Confirm that the device is receiving power by making sure that the “Power” LED is illuminated.
19

To ensure the highest security and prevent unauthorized usage of the HNC300 or HNC320W, the network administrator
has an exclusive privilege to access the cameras’ System Administration to change settings and control requirements that
allow entry and authorized privileges for all users. The HNC300 and HNC320W support multi-level password protection.
Access to the cameras is restricted to defined users only, who have a "User Name" and "User Password" that has been
assigned by the administrator.
Administrators can release a public user name and password so that when remote users access the HNC300 or HNC320W,
they will have access to view the images transmitted by the cameras.
Note:
When the HNC300 or HNC320W is used for the first time, it is highly recommended that the administrator set the
"Admin ID" and "Admin Password" to restrict users’ access to the cameras since the Default settings are the Null
String (i.e., the default Admin ID and Admin Password are blank). Once the ID and Password are defined, only
the administrator has access to manage the cameras. This operation should be performed as soon as possible since
the security features of the HNC300 and HNC320W will not be enabled until the "Admin ID" and "Admin
Password" are defined.
20