HazeBase piccola User manual

Manual

piccola
Scope of delivery
1 fog machine Piccola
1 magnetic Banded
1 250ml tank incl. Cover and quick coupling
1 3,4Ah / 12V AGM Battery incl. Holder
1 charger incl. Primary adapter
1 carrying case
1 instruction manual
Please check the completeness of the delivery
1

piccola
Table of content
1. Introduction 3
2. Safety 4
3. Name of the parts 5
4. Preparation 7
4.1 Selecting the location 7
4.2 Filling the tank 7
4.3 Hose cover 7
5. Working with the Piccola 8
5.1 Display of the Piccola 8
instructions5.2 Operation in stand-alone mode 8
5.3 mode selection in the 5 pin XLR connectors 9
5.4 operation DMX / RDM 10
5.5 operating cable remote control (optional) 10
5.5 operating by radio remote control (optional) 10
5.6 off the Piccola 11
6. the battery pack 12
6.1 change the battery pack 12
6.2 treatment of Battery packs 12
6.3 Charging the battery pack 13
6.4 Safety instructions for the battery pack 13
7. Vaporizer 13
7.1 Changing the vaporizer 13
8. Care and maintenance 15
9. Troubleshooting 16
10. Technical data 17
11. Guarantee 18
2

piccola
1. Introduction
The Piccola is a battery-operated smoke machine for use both as a fog effect in the
entertainment area, as well as for flow tests or leak detection. It only needs the
shortest heating times (1 sec.) And also has a compact housing with low weight
(2.6kg).
The Piccola only takes energy from the battery when a fogging process is started. This
process runs according to the following scheme.
1. Heating up (approx. 1 second)
2. Fluid pump delivers and fog is generated.
3. Follow-up time of 10 seconds (the heating is still active while the pump is
switched off).
The triggering of the fogging process can either take place via the trigger button on
the handle, or via the 5-pin XLR socket. There are three different operating modes
available for this.
1. DMX-512
2. Cable remote control (optionally available)
3. Radio remote control (optionally available)
ATTENTION!
The battery must be disconnected from the device when the Piccola is not in use. In
case of longer storage, the battery must be charged at regular intervals (every 6
months at the latest). Never store a discharged battery.
3

piccola
2. Safety
instructions Very hot steam comes out of the mist outlet opening. Caution,
risk of burns!
During the fogging process, very hot fluid droplets can occasionally emerge
from the fog outlet opening. For this reason, no people or heat-sensitive
objects may be located within 1.5 m of the fog outlet.
Never tamper with the mist outlet opening during operation or when it is
activated.
The device must be set up in a location that is not sensitive to heat.
Maintain a minimum distance of 60 cm to inflammable, combustible and
heat-sensitive objects.
The fog fluid used contains a glycol, which burns with a slightly bluish,
almost invisible flame. Therefore, never smoke into strong ignition sources
such as open fire.
Never open the device connected to a power source.
Occasional leakage of hot fluid droplets is possible during operation. Care
should therefore be taken to ensure that these cannot become a danger to
people. Maintain a safety distance of 3m from the fog outlet nozzle.
Do not ingest the fog fluid and keep it away from children. In the event of
contact with the eyes, rinse with plenty of water. Consult a doctor in case of
accidental ingestion.
Spilled or splashed fluid can create a slip hazard. Collect fluid and dispose of
according to regulations.
Do not let the visibility drop below 2m, you are responsible for people who
move in the foggy room.
The generated fog can trigger smoke alarms.
The method used here to generate artificial fog is largely harmless and is used
worldwide in the entertainment sector. We are not aware of any case in which a
healthy person was harmed by the use of this artificial mist. Nevertheless, we
recommend sick people or people with previous respiratory tract damage or
a tendency to allergies to contact with artificial fog avoid!
4

piccola
3. Designation of the parts
Front
Rear view
5

piccola
Top view
battery pack
6

piccola
4. Preparation
4.1 Selecting the location
The location at which the Piccola is operated must
●have good ventilation behave
●free of vibrations and shocks
●a non-flammable surface that is
●far enough away from easily flammable objects
●an ambient temperature between 5 ° C and 45 ° C
4.2 Filling the tank
1. If necessary, remove the two XLR plugs
2. Push the sleeve of the quick coupling (6) in the direction of the tank. The
plug-in socket (7) is then unlocked and can be removed from the quick
coupling.
3. Remove holder.
4. Unscrew the tank from the tank cap and fill it with original Base B fluid.
Make sure that no dirt gets into the tank. The suction strainer may have to
be cleaned.
5. Slide the tank back into the tank holder.
6. Insert the plug-in socket (7) back into the quick coupling (6). When this
locks, a distinct "click" sound be heard.
4.3 Hose
The Piccola is supplied with a hose cover for 15mm hoses. Please only use hoses that
can handle the temperatures. The hose cover is held by a magnet on the device. The
protruding ring on the hose cover is used for centering. This fits exactly into the mist
exit hole on the device.
The longer the mist duration is through the hose, the hotter the hose and the quality
of the mist decreases (becomes increasingly grayish). Small ventilation holes in the
hose directly on the hose cover can help improve this effect. Nevertheless,
condensation inevitably forms in the hose, which must be removed after each use.
7

piccola
5. Working with the Piccola
The Piccola is a battery-operated smoke machine with a directly heated evaporator. It
can generate the smallest clouds of fog to locate leaks, but it can also emit a larger,
effective fog cloud. The amount of mist can be set from 25% to 100% in 25% steps.
A single shot mode is also implemented.
5.1 Display of the Piccola
The operation of the Piccola takes place via the three buttons (minus / left, plus /
right, enter) and the OLED display. In the upper part of the display, the charge status
of the battery can be read on the left. The selected amount of fog is displayed in the
upper right part. The selected menu item is displayed in the middle. The respective
values are shown in the lower part of the display.
If a menu item is selected (see "Pump" above), the respective value can be changed
with the Minus / Left (9) and Plus / Right (10) buttons. The menu item can be
reached or exited with the Enter (11) key.
The Piccola is switched on using the release button (1) or one of the other three
buttons (9-11).
5.2 Operation in stand-alone mode
The simplest control case is stand-alone mode. This can be started with the release
button (1).
8

piccola
If the trigger button (1) has been used, the fogging process starts immediately,
according to the preset amount of fog. As soon as the trigger button is released, the
reheating process begins to empty the evaporator tube. After 10 seconds the Piccola
is switched off again and therefore no longer uses any electricity.
The following display appears in this stand-alone mode
No menu item has yet been selected. You can now switch
through the menu with the minus / left (9) and plus / right
(10) buttons. The menu sequence is Pump → Mode →
Info.
Use the Enter (11) key to switch to the menu item Pump setting. The following
settings can now be made here: single → 25% → 50% → 75% → 100%.
With the setting single-shot, only three pump blows are generated. This creates a
small burst of fog. To generate a second burst of fog, the release button must be
released and then pressed again. Leak tests can be carried out with this mode.
5.3 Mode selection of
the 5-pin XLR socket The next menu item is the setting of the mode for the 5-pin XLR
socket. When changing to this menu item, the following options are available: Manual
→ DMX → Remote.
The socket is deactivated in manual mode. The device can only be using started the
trigger button.
In DMX mode, the socket is used to receive a DMX-512 telegram. Furthermore, the
Piccola is RDM capable, so the DMX address can also be using an RDM changed
capable lighting console. A firmware update via RDM is also possible.
In remote mode, the Piccola can be using triggered wired remote control or a radio
remote control.
If a mode other than manual is selected, the main menu is expanded to include the
corresponding sub-items.
9

piccola
5.4 Operation via DMX / RDM
The menu item DMX has now been added to the main
menu. By selecting this menu item you get to the setting of
the DMX address.
This can be changed using DMX address the minus button
(9) and plus button (10). The address is automatically
adopted after two seconds. This is indicated by flashing the
address .
If a valid DMX signal is received, a small "R" appears above
the quantity display.
Since the Piccola needs energy from the battery for DMX reception, in this case it
switches off one hour after the last valid DMX signal. This saves the battery.
5.5 Operation via cable(option)
The remote control “Remote” menu item has now been
added to the main menu. Selecting this menu item takes
you to the settings for the connected remote control. If a
remote control has not yet been connected, “no remote
found” appears in the display. As soon as a cable remote
control is connected, however, an "analog found" appears.
If a valid signal is received, a small "R" appears above the
quantity display. If the potentiometer on the remote control
is turned over 10% and the switch is switched on, the
fogging process is started. The output can now be 25%. 50%, 75% and 100% can be
set.
5.5 Operation via radio remote control (option)
If a radio remote control is connected, "radio found"
appears in the display. The fogging process can be
triggered by pressing the appropriately programmed button
on the hand transmitter. The pump value is adopted from
the setting on the device.
When using a radio remote control, several hand-held
transmitters can be trained on the receiver. A selection of
10

piccola
the button on the hand-held transmitter can also be specified.
To learn a hand-held transmitter, please activate the menu
item "add sender". Then “searching” appears in the display.
Now please press a button on your hand transmitter. When
the hand-held transmitter has been taught successfully in,
"adding" appears on the display.
You can then continue by selecting the button on the hand transmitter.
To do this, select buttons 1 to 4 using the plus and minus
buttons. Here, too, the set value is automatically saved after
two seconds.
The Piccola now triggers the fogging process when the set
button is confirmed.
It is also possible to delete the learned hand-held
transmitters from the memory. To do this, select the “del all
sender” menu.
All learned hand-held transmitters are now removed from
the memory.
5.6 Switching off the Piccola
The Piccola switches itself off automatically after the
fogging process in order to extend the battery life.
However, if a mode other than "Manual" is set, the Piccola
can be switched off using the "Off" menu item.
Note that the machine can then only be switched on using the buttons on
the device !
11

piccola
5.7 Machine information
In the “Info” menu item, the serial number and the
firmware version of the Piccola can be read.
6. The battery pack
The supplied battery pack contains a maintenance-free 12V lead-gel battery. This can
be used independently of the location. The Piccola is connected via a 4-pin. XLR
connector. The charger is connected via a low voltage socket.
When used properly, the battery retains its capacity for several years and has several
hundred charge / discharge cycles.
6.1 Changing the battery pack
To change the battery pack, first disconnect the battery from the device (4-pin XLR
plug). Then disconnect the hose connection to the tank and remove the tank from the
battery pack.
Now loosen the two knurled screws (3) and remove the device from the battery pack.
Mount the new battery pack in reverse order.
6.2 Handling the battery pack
The lead gel battery is a robust energy storage device that requires little care and
maintenance. Nevertheless, incorrect use and storage can greatly reduce the service
life.
Therefore: Never discharged battery store!
As a result, the battery can lose a large part of its capacity within a few weeks. If the
battery is stored for a longer period, it must be recharged regularly (at least every 6
months).
For safety reasons, always disconnect the battery from the device during
transport.
12

piccola
6.3 Charging the battery pack
Please use the power supply unit supplied to charge the battery pack. The charge
control indicator lights up red during the charging process. When the battery is
charged, the color changes to green.
6.4 Safety instructions for
●the battery pack Never short-circuit the battery, never reduce the cable
cross-sections.
●Always operate the battery in a ventilated housing.
●Never disassemble the battery.
●Never expose the battery to fire or burn it. This could cause an explosion.
●Keep the battery away from sources of heat. A battery temperature above
45 ° C should not be exceeded.
7. Evaporator
7.1 Replacing the evaporator
If the mist emission decreases, the
evaporator should be replaced.
To do this, please loosen the two
screws on the top of the cover.
13

piccola
The four screws on the underside of the device
can then be removed.
Now carefully remove the lid of the Piccola.
Carefully remove the ribbon cable from the
connector on the motherboard.
Then remove the screw from the evaporator
board.
The evaporator can now be released by
levering a small screwdriver through the
two openings.
Now remove the fluid hose from the old vaporizer
and attach it to the new one.
Remove all fluid residues in the unit using a cloth.
Then mount the new evaporator in the device in reverse order and close the housing.
The new vaporizer can be used immediately.
14

piccola
8. Care and maintenance
Avoid the Piccola without fluid. Otherwise, the pump will run dry.
Avoid overheating the device from direct sunlight or direct headlights. The
permissible ambient temperature can be found in the technical data.
Immediately wipe up any leaked fluid.
Check the suction strainer in the tank from time to time. Clean it or replace
it.
If the same fluid canister is used frequently, you should rinse it out
thoroughly with fresh fluid before filling it. This will avoid contamination.
Clean the surface of the If device necessary, with a suitable, solvent-free
cleaning agent.
If necessary, clean the inside of the device in the area of the evaporator.
PLEASE NOTE: The evaporator of our fog machines does NOT have to be
cleaned! Cleaning fluids that are available on the market can damage the
vaporizer! In this case the guarantee is void.
15

piccola
9. Troubleshooting
The Piccola does not smoke
●Check external control
●Check battery
●Check fluidlevel
●Check the connection on the fluid tank for leaks
●Check the suction strainer in the tank for contamination
●Check the fluid hose and connector for leaks
The Piccola suddenly switches off
●The battery is empty. The message "empty battery" appears in the display.
●The temperature fuse in the evaporator is defective. The error message
"HEM Error" appears in the display.
The Piccola hums loudly when fogging.
●The pump runs dry. This must be avoided at all costs.
●Refill fluid Check
●hose and coupling, engage again if necessary.
16

piccola
10. Technical data
Functional principle
evaporator fog machine, directly heated,
battery operated
Connection
200W, 12V DC Heating
Heating time
1 second
Fluid tank
250ml
fog density
Adjustable in 25%, 50%, 75%, 100%, single
shot
Battery life
Up to 30 min at 25%
Up to 10 min at 50%
Up to 6 min at 75%
Up to 4 min at 100%
fluid consumption
1.5 ml / min at 25%
3.0 ml / min at 50%
4.5 ml / min at 75%
6.0 ml / min at 100%
assisted Protocols
DMX-512, RDM
battery
lead-gel, 12V / 3.4Ah
Charger adapter
15W / 18V DC, wide-range input (90-264V)
with exchangeable primary
Supported types of fluids cover
base*B
Optional accessories
radio remote control, cable remote control via
5-pin XLR, hose, 5-pin XLR cable whip
Weight
2.6kg
Dimensions (LxWxH)
203 x 79 x 163 mm (including battery and
tank holder)
17

piccola
11. Guarantee conditions
For the purchased Piccola smoke, hazebase provides a guarantee according to the
following conditions:
1. We repair free of charge in accordance with the following conditions (No. 2 to 6)
Damage or defects in the device, i.e. e are demonstrably based on
manufacturing defects if they are reported to us immediately after detection and
within 24 months of delivery to the end user. A guarantee obligation is not
triggered by minor deviations from the target quality, which are irrelevant for the
value and usability of the device, by damage from the effects of water and
generally from abnormal environmental conditions or force majeure.
2. The guarantee is provided in such a way that defective parts are repaired free of
charge or replaced by faultless parts, at our option. Devices for which a
guarantee service is claimed with reference to this guarantee must be handed
over to us and sent carriage paid.
The purchase receipt with the date of purchase and / or delivery must be
submitted. Replaced parts become our property.
3. The warranty claim expires if repairs or interventions are carried out by persons
who are not authorized to do so by us or if our devices are provided with
additional parts or accessories that are not matched to our devices.
Furthermore, the guarantee expires if a different from the original hazebase fog
fluid was used. If the devices are sent to us without the fluid canister having
been removed or emptied beforehand, the guarantee is also void, as is the case
with verifiable disregard of the operating instructions or errors due to improper
handling / handling and damage caused by force.
4. We do not grant any performance claims on components or component groups
that are subject to natural wear and tear or normal wear and tear. In particular,
all fluid-conveying parts such as pumps and heating elements / evaporators are
considered wear parts. A goodwill regulation will be checked on a case-by-case
basis.
5. Guarantee services do not result in an extension of the guarantee period, nor do
they initiate a new guarantee period. The guarantee period for installed spare
parts ends with the guarantee period for the entire device.
18

piccola
6. If a damage or a defect cannot be remedied by us, or the improvement is
refused or unreasonably delayed by us, within 6 months from the date of
purchase / delivery, at the request of the end customer, either
a. Replacement delivered free of charge or
b. the reduced value is compensated or
c. the device will be taken back against reimbursement of the purchase price,
but not beyond the market price.
7. Further or other claims, in particular those for replacement of damage caused
outside the device, are excluded - unless liability is mandated by law.
19