HCO ADAMM-RSM User manual

Placing Device on Body
Place the ADAMM-RSM™ wearable anywhere on the upper torso (the area below the base of
the neck and above the stomach on the front, side, or back).
Tip: Do not slouch when sticking on the ADAMM-RSM.
Tip: Figure out a few comfortable positions to wear the ADAMM-RSM and alternate
wearing it in those positions from day to day.
Charging
• Remove any adhesive from the back of the wearable.
• Place the wearable in the charging cradle with the gold points lined up as shown.
Close the cradle and secure it with the strap.
• Make sure the cradle is connected to the wall adapter and the wall adapter is plugged
into the electrical outlet.
NOTE: Only use the provided USB Adapter.
• The indicator light 7will light on the wearable (it may take a few seconds). If the lights
do not show, power ON the wearable. Reset if required.
- Flashing RED - indicates the wearable is charging
- Steady RED - indicates the wearable is fully charged
• The device should NEVER be worn while charging.
Wi-Fi Syncing
• Press the wi-fi sync button 1to enable Wi-Fi Sync feature on the ADAMM-RSM™ device.
During this time the indicator light 4will flash BLUE in color.
NOTE:
Use Wi-Fi to upload data to cloud nightly or at least a few times a week.
How to Use ADAMM-RSM
Quick Start Guide
1 Pleasant St, Ste 442
Rochester, NY 14604 USA
Office: 585-471-8215
Email: [email protected]
QSG-B0001

You should have:
ADAMM-RSM
Adhesive Pack
Charging Cradle
USB Wall Adapter
Turning ON and Turning OFF ADAMM-RSM
1. Turning ON:Press and hold 2for 4 seconds and then release. 5blinks blue and then
green as it powers UP.
2. Turning OFF:Press and hold 2until the device vibrates (approximately 10 seconds) and
release as soon as the device starts to vibrate. If 5lights up during this time, stop and
repeat in one minute.
3. Reset If Not Turning ON:Press and hold 2for 20 seconds. If 5lights up during this
time, stop the reset, as the light means the device is now turning ON.
Tip: A vibration will occur when you press 1if the device is ON.
Applying the Adhesives
Quick Reference for using ADAMM-RSM
1
1
2
2
6
7
4
4
5
5
7
6
3
3
‘ON’ Check & Sync Button
Power Button
Voice Journal (optional)
Indicator Light
Indicator Light
Charging Contacts
Indicator Light
1. Hold the clear liner and
peel the white liner away
from the adhesive pad.
2. Hold the clear liner and
match the adhesive shape
with the device.
3. Press the adhesive pad
onto the device as shown.
4. Peel the clear liner
off without lifting the
adhesive off the device.

You should have:
ADAMM-RSM
Adhesive Pack
Charging Cradle
USB Wall Adapter
Turning ON and Turning OFF ADAMM-RSM
1. Turning ON:Press and hold 2for 4 seconds and then release. 5blinks blue and then
green as it powers UP.
2. Turning OFF:Press and hold 2until the device vibrates (approximately 10 seconds) and
release as soon as the device starts to vibrate. If 5lights up during this time, stop and
repeat in one minute.
3. Reset If Not Turning ON:Press and hold 2for 20 seconds. If 5lights up during this
time, stop the reset, as the light means the device is now turning ON.
Tip: A vibration will occur when you press 1if the device is ON.
Applying the Adhesives
Quick Reference for using ADAMM-RSM
1
1
2
2
6
7
4
4
5
5
7
6
3
3
‘ON’ Check & Sync Button
Power Button
Voice Journal (optional)
Indicator Light
Indicator Light
Charging Contacts
Indicator Light
1. Hold the clear liner and
peel the white liner away
from the adhesive pad.
2. Hold the clear liner and
match the adhesive shape
with the device.
3. Press the adhesive pad
onto the device as shown.
4. Peel the clear liner
off without lifting the
adhesive off the device.

Placing Device on Body
Place the ADAMM-RSM™ wearable anywhere on the upper torso (the area below the base of
the neck and above the stomach on the front, side, or back).
Tip: Do not slouch when sticking on the ADAMM-RSM.
Tip: Figure out a few comfortable positions to wear the ADAMM-RSM and alternate
wearing it in those positions from day to day.
Charging
• Remove any adhesive from the back of the wearable.
• Place the wearable in the charging cradle with the gold points lined up as shown.
Close the cradle and secure it with the strap.
• Make sure the cradle is connected to the wall adapter and the wall adapter is plugged
into the electrical outlet.
NOTE: Only use the provided USB Adapter.
• The indicator light 7will light on the wearable (it may take a few seconds). If the lights
do not show, power ON the wearable. Reset if required.
- Flashing RED - indicates the wearable is charging
- Steady RED - indicates the wearable is fully charged
• The device should NEVER be worn while charging.
Wi-Fi Syncing
• Press the wi-fi sync button 1to enable Wi-Fi Sync feature on the ADAMM-RSM™ device.
During this time the indicator light 4will flash BLUE in color.
NOTE:
Use Wi-Fi to upload data to cloud nightly or at least a few times a week.
How to Use ADAMM-RSM
Quick Start Guide
1 Pleasant St, Ste 442
Rochester, NY 14604 USA
Office: 585-471-8215
Email: [email protected]
QSG-B0001