Hde Firefly Instruction Manual

Operating nstruction Manual

FIREFLY

and TESTER

FUSE TOOL & VOLTAGE DETECTOR

1475 Lakeside Drive • Waukegan, llinois 60085 U.S.A. • 847.473.4980

fax 847.473.4981 • website: www.HDElectricCompany.com

Making the Invisible VisibleTM

MPORTANT SAFETY NFORMAT ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

DESCR PT ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

VOLTAGE DETECTOR SELF-TEST OPERAT ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

NSTRUCT ONS FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

OPERAT ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

BATTERY REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

MA NTENANCE AND CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

TECHN CAL SPEC F CAT ONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

OPT ONAL ACCESSOR ES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

WARRANTY AND L AB L TY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

1475 Lakeside Drive • Waukegan, llinois 60085 U.S.A. • 847.473.4980

fax 847.473.4981 • website: www.HDElectricCompany.com

Operating nstruction Manual

FIREFLY

and TESTER

FUSE TOOL & VOLTAGE DETECTOR

MPORTANT SAFETY NFORMAT ON

READ AND UNDERSTAND ALL ELEMENTS OF THIS MANUAL PRIOR TO USE.

WARNING: Use of the FireFly Fuse Tool Voltage Detector in certain corner locations

may result in incorrect indications. Those conditions should be avoided or re-tested

in a nearby location. Voltage cancellation effects inside right angles (conductors

approximately 90° apart) may cause false indications if the Detector is used within

3 feet (1 meter) of the conductors joining. Other operating limitations may exist.

These are found in the nstructions for Use section of this manual (page 6).

DANGER: Never insert the FireFly Detector into metal enclosures, switchgear, through

access holes or use in any situations other than overhead conductors. ncorrect

use of the FireFly Detector can lead to severe injury or death.

SAFETY

Rigorous hotstick work practices should be used at all times. All industry, OSHA and

company work practices and safety procedures shall apply when working on or near

high voltage systems. When used properly, the FireFly Detector reliably provides an

alarm warning of energized conductors.

• Only trained, professional operating personnel should use this equipment. The

voltages these instruments operate at are to be considered live and dangerous

and are lethal. Severe injury or death can occur if improperly used.

• Make certain all other safety considerations have been identified, implemented

and are in place prior to using this equipment. Maintain proper work clearances

at all times.

• Make certain the FireFly Detector is properly rated for use on the system voltages

you will test.

• Prior to using, make certain to inspect the instrument for any physical damage,

cleanliness and check for proper working order using the test button. Remove

from service and do not use if you suspect a problem with any of the above.

• Test the instrument before and after each use by testing on a known voltage source

such as the PT-FTVD Proof Tester® Detector Tester for FireFly Voltage Detectors.

• Never allow another high voltage conductor, or grounded point, to come in

contact with the tool during use. Keep housing of FireFly Detector free and

clear of all structures at all times.

• Hotsticks must be used at all times per industry, OSHA and company work practices.

• Never touch the detector or control panel during contact with high voltage. The FireFly

Detector should be considered to be at the same voltage as the conductor under test.

DESCR PT ON

The FireFly Detector combines a lighted fuse tool with voltage detection adding

an extra margin of safety for those working on distribution lines. Operating

frequency is 60Hz (optional 50Hz available).

The FireFly Detector includes is a single range voltage detector. One range of

operating voltages is set within the unit. A typical range is 4kV-12kV. f the unit

contacts a conductor energized from 4kV (line-to-line) to 12kV (line-to-line),

red LEDs flash and an audible alarm is activated.

Other FireFly Detector voltage ranges are available up to and including 35kV.

Do not use the detector at voltages higher or lower than it is rated. Consult

the product label for the specific range or levels for the unit supplied.

When operating within the unit’s voltage range (see product label), the FireFly

Detector will provide both an audible and visual alarm upon making contact

with an energized conductor. The FireFly Detector units will not give an alarm

due to induced voltage on de-energized conductors, unless the induced voltage

level exceeds the threshold voltage of the detector.

The FireFly Detector should be tested both prior to and after line testing to make

certain the unit is working properly. The FireFly Voltage Detector has a built-in

self-test feature to make certain the unit is working properly. Push the TEST button,

which will test the battery, the electronic circuitry and the audible and visual alarm

(see page 5 for more information). To test the FireFly Detector on a known voltage

source before and after each use, the PT-FTVD Proof Tester FireFly Voltage Detector

Tester can be used (see page 10 for more information).

f the FireFly Detector does not pass the self-test, the voltage detector batteries

should be replaced and the unit re-tested. f the unit still does not pass the test,

the unit should be sent in for repair. NEVER USE THE F REFLY DETECTOR F THE

SELF-TEST S NOT SUCCESSFULLY PASSED! See Self-Test Operation Section (page 5).

Four (4) 3V lithium batteries power the FireFly Voltage Detector and white lights.

Even though the voltage detector is always “ON” and sensing voltage, the voltage

sensor batteries should last for approximately one year under normal use. We do

recommend however, replacing the batteries every six months. f the instrument

is to be stored for a year or more, remove the battery during storage.

A universal spline adapter is built into the aluminum housing of the FireFly Detector

units. Extension hotsticks are required for use at all times. Hotsticks are available from

HD Electric Company and must be used when placing the FireFly Detector in contact

with any conductor.

VOLTAGE DETECTOR SELF-TEST OPERAT ON

The self-test feature provides a full test of the battery, the voltage detection circuitry

and the audible and visual alarm.

NOTE: The self-test should be used both prior to and after testing the conductor to

confirm proper operation.

1) Push and hold the self-test button on

the front panel to operate the self-test.

The red (alarm) LED lights will flash

and the buzzer will beep. The unit

is ready for operation (Figure 1).

2) f pressing the test button does not cause

the events listed in Step 1, the unit should

not be placed in operation. The battery

may need replacement, see Battery

Replacement section (page 8). f changing

the battery does not produce the results

shown in Step 1, remove the unit from service

and send in for repair.

3) After completing the voltage detection on the conductor (see next section), always

confirm proper function of the FireFly Detector by completing Step 1 again. f the

self-test does not function as above, DO NOT assume that the test results are correct.

Re-test the conductor, preferably with a different FireFly Detector.

4) Verify the operation of the white lights by pressing the Lights ON/OFF button.

Verify both the top and side white lights turn on. Replace the two Lights batteries

if the lights do not come on (page 8).

NOTE: Never use the self-test if the FireFly Detector is in contact with any voltage source.

F gure 1

NSTRUCT ONS FOR USE

S tuat ons To Avo d

Within certain situations and because of various system configurations, electrical field

interference capable of affecting the operation of the FireFly Voltage Detector may

occur. Within these areas it is imperative that you be aware of and identify all such

conditions which may exist. Some examples of these situations are discussed here.

1) 90° CORNER CONFIGURATIONS: Using the FireFly Detector on the inside of 90°

corners may cause reduced voltage sensitivity or a failure to indicate voltage.

2) SAME PHASE INTERFERENCE: When two conductors of the same phase are

in close proximity to one another, the field generated could shield the FireFly

Detector, causing it not to operate.

3) OPPOSITE PHASE INTERFERENCE: This condition may occur when testing

a grounded and de-energized conductor which is in close proximity to

a live, ungrounded conductor. n this situation the FireFly Detector may indicate live

voltage when the conductor being contacted is at ground potential.

NOTE: Only use the FireFly Detector within the voltage range specified on the product

label. Do not use the FireFly Detector above or below the product label rating.

DANGER: Never allow the body of the FireFly Detector to bridge across, or come

in contact with, another conductor or grounded point.

OPERAT ON

NOTE: Direct, metal-to-metal contact with the conductor must be made for the

FireFly Voltage Detector to operate correctly.

1) Place the FireFly Detector at the end of a hotstick adequate for protection for the

voltage range being tested. Company, OSHA and industry safety procedures

MUST BE FOLLOWED AT ALL T MES. Connect the detector to the hotstick by

way of the built-in universal spline, making certain it is securely attached.

2) f the FireFly Detector will be used at night or in the dark, test the Lights before

use. The lights will shut off automatically 10 minutes after the most recent

voltage detection or self-test, or they can be turned off manually.

3) Place the FireFly Detector in direct contact with the conductor being tested for

voltage or inside the loop of the fuse cutout or switch. The FireFly Detector

should be positioned as close to a 90° orientation (perpendicular) to the fuse

or switch as possible. f the conductor is energized, the detector will give both

an audible (beeping tone) and visual (red blinking lights) indication. f the

conductor is not energized no signal is given.

When operating within the unit’s voltage range (see product label), the FireFly

Detector will provide both an audible and visual alarm upon making contact

with an energized conductor. The FireFly Detector unit will not give an alarm

due to induced voltage on de-energized conductors, unless the induced

voltage level exceeds the threshold voltage of the detector.

4) Test the FireFly Detector for proper voltage detection after each use by

pushing the TEST button. See the Self-Test Operation section (page 5).

The PT-FTVD Proof Tester FireFly Voltage Detector Tester can also be used to

test the FireFly on a known voltage source before and after use (page 10).

BATTERY REPLACEMENT

Replace the four batteries as needed with EC type CR17345 including Duracell® 123,

Panasonic® CR123A and Energizer® 123. Note: Panasonic® type CR17335 or BR-2/3A

are not acceptable replacements. Two of the four batteries power the voltage detector

and the other two power the white lights. Always replace the two batteries for each

function in pairs, but it is not necessary to replace all four batteries at the same time.

1) Remove the molded plastic inner housing from the aluminum outer housing by

pressing and holding the two latches on the front of the unit and pushing through

the hole in the back of the unit.

2) Pull the battery cover off of the back of the molded housing.

3) Replace batteries as needed for the voltage detector and/or the white lights. Verify

correct battery polarity.

4) Replace the battery compartment cover and push the molded housing back into

the aluminum holder right side up. Ensure both latches snap into place.

MA NTENANCE AND CARE

STORAGE - t is recommended for protection of the FireFly Detector that you always

store it and its accessories in the carrying bag provided. f a prolonged period of

storage is anticipated (six or more months), remove the batteries. Remember to

replace the batteries prior to using the FireFly Detector again.

CLEANLINESS - The aluminum outer housing is very rugged, but it should be kept

clean and free of dirt, grease and any other foreign materials. The inner plastic housing

should also be kept clean and dry. f either housing surface integrity has been

compromised in any way, return the FireFly Detector to the factory for repair or

replacement. Do not use.

DAMAGE - f you suspect any mechanical or electrical damage, do not use the

FireFly Detector and arrange for repair by returning to the factory.

BATTERY REPLACEMENT - See Battery Replacement section (page 8)

for additional information.

CALIBRATION & TESTING - t is recommended that every twelve months the

FireFly Detector is sent in for testing, cleaning and inspection. We recommend

this to be done at a factory trained repair facility, the HD Electric Company factory,

or other qualified location.

Minimal maintenance is required for the FireFly Detector. The carrying bag that is supplied

with the unit is recommended for storage of the FireFly Detector when it is not in use.

TECHN CAL SPEC F CAT ONS

ENVIRONMENTAL CONDITIONS

COND T ONS - ndoor and outdoor use

ALT TUDE - Up to 6,566 ft. (2000M)

OPERAT NG TEMPERATURE -40°F to +120°F (-40°C to +49°C)

HUM D TY - 95% to 49°C (non-condensing)

MEASUREMENT CATEGORY V

OVERVOLTAGE CATEGORY V

ENCLOSURE MATER AL - Aluminum, polycarbonite

DIMENSIONS:

LENGTH - 6 in. (15cm), Width 1.2 in. (3cm), Height 6 in. (15cm)

WE GHT - 1 lb. (454g)

BATTERY L FE - Voltage detection - up to 40 hours continuous alert

White lights - up to 8 hours continuous

BATTERY - 3V lithium, ANS -5018LC, EC-CR17345

VOLTAGE DETECT ON RANGE - Voltage ranges available from

4kV to 35kV system voltage, 50/60Hz.

OPT ONAL ACCESSOR ES

PT-FTVD TESTER FOR FIREFLY DETECTORS

The PT-FTVD Proof Tester® FireFly Detector Tester

is for use on all FireFly Detector models. This

tester generates high voltage AC for testing

the FireFly Voltage Detector.

To use, apply the metal plate on the bottom of the

FireFly Tester to the right side of the Firefly Detector

housing as shown. Press and hold the TEST button

on the Proof Tester. A properly operating FireFly

Detector will signal the presence of voltage with

both the beeper and red lights. f the FireFly Voltage

Detector does not operate, replace the Voltage

Detector batteries, per the instructions (page 8).

f the Proof Tester LED does not light, replace the

Proof Tester battery with a 9V lithium

or alkaline type battery.

CAUTION: This device generates high

voltage AC for testing the voltage detection

function in FireFly Detectors. There is no

danger of electric shock when this Tester

is used as directed. Discontinue use and

return to HD Electric Company for service

if the housing is cracked or broken,

or if the battery cover is lost.

WARNING: Do not use this Tester except

as directed. Do not use to test equipment

other than specified FireFly Voltage Detectors.

Do not apply to energized circuits or equipment.

Do not operate this Tester without the

battery cover and do not open the housing.

Refer all servicing to the factory. Failure to

follow these instructions may lead to

electric shock, severe injury or death.

HOTSTICKS

A range of hotsticks are available in lengths starting

at 4’. Contact HD Electric for more details.

LIMITED WARRANTY AND LIMITATION OF LIABILITY

This warranty applies to all products sold by HD Electric Company (the "Products"); provided, however, that the term Products does not include any

third party products purchased through HD Electric Company, for which no warranties are made (the "Third Party Products"). Third Party Products

may be subject to a separate manufacturer's warranty; [should you have any question regarding whether a separate warranty applies, please contact

HD Electric Company].

NOT CE: READ TH S L M TAT ON OF WARRANTY AND L AB L TY BEFORE BUY NG OR US NG THE PRODUCTS CONTA NED HERE N.

t is impossible to eliminate all risks associated with the use of the Products. Risks of serious injury or death, including risks associated with electrocution,

arcing and thermal burns, are inherent in work in and around energized electrical systems. Such risks arise from the wide variety of electrical systems

and equipment to which Products may be applied, the manner of use or application, weather and environmental conditions or other unknown factors,

all of which are beyond the control of HD Electric Company.

HD Electric Company does not agree to be an insurer of these risks, and shall have no liability for any claims arising from such risks.

WHEN YOU BUY OR USE THESE PRODUCTS, YOU AGREE TO ACCEPT THESE R SKS.

HD Electric Company warrants to the original purchaser that the Products (excluding any third party products purchased through HD Electric Company,

for which no warranties are made) will be free from defects in material and workmanship, under normal use and regular service, and preventative

maintenance for a period of one (1) year (ten (10) years for HDE Capacitor Controls) from the date of shipment (the “Warranty Period”). Should any failure

to conform with this warranty be found during the Warranty Period, you must notify HD Electric Company of your claim within thirty (30) days of discovery,

and within the Warranty Period. Your failure to give notice of claims of breach of warranty within the Warranty Period shall be deemed an absolute and

unconditional waiver of claims for such defects. HD Electric Company will have no responsibility to honor claims received after the date the applicable

Warranty Period expires.

Upon notice of your claim, HD Electric Company will provide a return authorization number, and further instructions on how to return the product for

service. You must follow HD Electric Company’s instruction. You are responsible for all Product removal, handling, re-installation, and shipping (both

to and from HD Electric Company). Products returned for repair, as well as repaired or replacement Products shall be sent postage / freight prepaid. After

receipt of a product which HD Electric Company determines is defective, HD Electric will, at its option, either (1) repair (or authorize the repair of) the

Product or (2) replace the Product, subject to the following: The Products are made using parts sourced from a variety of manufacturers. Due to the rapidly

changing technology environment, parts may become obsolete / unavailable over time (end of life). n the event that a Product cannot be repaired or

replaced due to unavailability of parts, HD Electric Company will use commercially reasonable efforts to obtain substitute parts or conduct work around

design, but cannot guarantee its ability to do so.

tems not found defective will be returned at your expense, or failing receipt of instruction from you on return of such items within five (5) business days

of our notice to you that the product is not defective, HD Electric may dispose of the product at its discretion and with no liability to you. HD Electric

Company’s determination of defects is final. Products repaired or replaced during the Warranty Period shall be covered by the foregoing warranties for

the remainder of the original Warranty Period or ninety (90) days from the date of delivery of the repaired or replaced Products, whichever is longer.

LIMITATIONS:

This warranty is void in the event of misuse, alteration, faulty installation, or misapplication of the product.

This warranty does not cover failure of product or components due to any ACT OF NATURE; lightning, floods, hurricanes, tornadoes or any other such

catastrophic events.

HD Electric Company does not warrant any third party products or associated hardware or their performance or suitability for use and application. Such

items are provided “as-is”.

All repairs must be authorized by HD Electric Company. Unauthorized repairs will not be reimbursed under any circumstances.

HD Electric Company is not required to make replacement or loaner equipment available while Products are being repaired or replaced, or to compensate

you for any in/out labor charges or expenses associated with removal, handling or re-installation of the Products.

TO THE MAX MUM EXTENT PERM TTED BY LAW, TH S WARRANTY AND THE REMED ES SET FORTH ABOVE ARE EXCLUS VE AND N L EU OF ALL OTHER

WARRANT ES, REMED ES AND COND T ONS, WHETHER ORAL OR WR TTEN, EXPRESS OR MPL ED. HD ELECTR C EXPRESSLY D SCLA MS ALL OTHER

WARRANT ES OF ANY K ND, EXPRESS OR MPL ED, NCLUD NG W THOUT L M TAT ON MPL ED WARRANT ES OF F TNESS FOR A PART CULAR PURPOSE,

MERCHANTAB L TY AND NON- NFR NGEMENT.

N NO EVENT SHALL HD ELECTR C COMPANY BE L ABLE FOR ANY ND RECT, NC DENTAL, CONSEQUENT AL OR SPEC AL DAMAGES RESULT NG FROM THE

USE OR HANDL NG OF THESE PRODUCTS. TH S SHALL NCLUDE BUT, NOT L M TED TO, LOST PROF TS OR REVENUE, LOSS OF USE OF THE PRODUCTS,

COST OF SUBST TUTE PRODUCTS, FAC L T ES OR SERV CES, OR DOWNT ME.

N NO EVENT SHALL HD ELECTR C COMPANY HAVE ANY L AB L TY FOR ANY TH RD PARTY PRODUCTS OR ASSOC ATED HARDWARE, OR

CUSTOMER-OWNED SYSTEMS, EQU PMENT OR SOFTWARE.

HD Electric Company must have prompt notice of any claim so that an immediate product inspection and investigation can be made. Buyer and all

users shall promptly notify HD Electric Company of any claims, whether based on contract, negligence, strict liability, or other tort or otherwise be barred

from any remedy.