Hearth and Home Technologies RCT-MLT-II User manual

1
Printed in U.S.A. Copyright 2008,
Hearth & Home Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044 100-907F 4/08
RCT-MLT-II Remote Control Kits
- Installation and Operating Instructions -
INTRODUCTION
Theremotecontrolsystemcanbeoperatedthermostati-
cally or manually from the transmitter. The system oper-
atesonradiofrequencies(RF) withina20 footrange.Can
be used with DSI, IPI or Standing Pilot systems.
This remote control kit has a hand held transmitter that
can be used as a remote on/off or as a thermostat. The
transmitterdisplayshowsthecurrentroomtemperature,
target temperature, timer setting, on/off status, low bat-
tery indicator, current time, burner/valve operation and
fan operation. Electrical ratings for the receiver are: 110
VAC, 60 Hz, 6 W.
If pertinent, see additional fireplace wiring diagrams on
pages 9 to 11.
INSTALLATION PRECAUTIONS
This remote control kit is tested and safe when installed
in accordance with this installation manual.
FCC REQUIREMENTS
WARNING: DO NOT CONNECT 110-120 VAC
WIRING TO THE GAS CONTROL VALVE OF THIS
APPLIANCE.
It is the responsibility of the installer to read all instruc-
tions before starting installation and to follow these
instructions carefully during installation. Modification of
the remote control system or any of its components will
void the warranty and may cause a fire hazard.
NOTE: The factory installed junction box in the gas
fireplace must be wired with 110 VAC before install-
ing this kit. See Installation Instructions section.
CAUTION: All wiring should be done by a qualified
electrician and shall be in compliance with local codes
and with the National Electric Code ANSI/NFPA No. 70-
current (in the United States), or with the current CSA
C22.1 Canadian Electric Code (in Canada).
NOTE: A manometer MUST be used to set the
manifold pressure on the gas valve.
Installation of this kit MUST be done by a qualified
service technician.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designedtoprovidereasonable protection against harm-
ful interference in a residential installation. This equip-
ment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
theinstructions,maycauseharmfulinterferencetoradio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
ortelevisionreception,whichcanbe determined by turn-
ing the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
- Consult the dealer or an experienced radio TV techni-
cian for help.
Canadian Equipment Requirements
Thisdigital apparatusdoesnot exceedthe(ClassA/Class
B)* limits for radio noise emissions from digital appara-
tus set out in the Radio Interference Regulations of the
Canadian Department of Communications. Le present
appareilnumeriquen’emet pas debruitsradioelectriques
depassant les limites applicables aux appareils nume-
riques (de la class A/de la class B)* prescrites dans le
Reglement sur le brouillage radioelectrique edicte par le
ministere des Communications du Canada.
This device complies with RSS-210 of Industry and Sci-
ence Canada. Operation is subject to the following two
conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, includ-
ing interference that may cause undesired operation of
the device.
WARNING: CHANGES OR MODIFICATIONS TO
THIS UNIT NOT EXPRESSLY APPROVED BY
THE PARTY RESPONSIBLE FOR COMPLIANCE
COULDVOID THEUSER’SAUTHORITYTOOPER-
ATE THE EQUIPMENT.

2
Figure 1
REMOTE RECEIVER
Important: The remote receiver should be positioned
close to front in right or left corner where ambient
temperatures do not exceed 170º F.
Theremotereceiverispoweredby110-120VAC. It plugs
into a standard polarized duplex receptacle.
Locating Receiver and Operating Functions
Thisremotereceivercanbepositionedunderthefirebox
in the control compartment of the fireplace if ambient
temperatures do not exceed 170º F. This system is de-
signed to control the following components:
INSTALLATION INSTRUCTIONS
Installing Electrical Service to the Junction Box
RECEIVER WIRING INSTRUCTIONS
Incorrect wiring connections WILLcause damage to the
gas valve or electronic module operating the gas appli-
ance and may also damage the remote receiver.
Wiring Flame Function (Standing Pilot, DSI, IPI)
Connect the remote receiver by connecting the two red
wires leading from the remote receiver to the red and
brown remote wires labeled “FOR USE WITH REMOTE
OR WALL SWITCH ONLY”. See Figure 2.
Figure 2.
Alternative Wiring for units with a wall switch
Disconnect the wall switch wire from the TH terminal on
the valve and connect this wire to male connector sup-
pliedonthereceiver. Connect remaining female connec-
tor from receiver to the TH terminal on the valve.
Adding Optional Fan/Blower
Plug 2-prong fan cord directly into the 3 prong polarized
plug on the back of the receiver (see Figure 3). This
receptacle output is 110/120 VAC, 3 AMP.
Wire Colors
• Gas Valve - Millivolt or
Electronic Ignition .............................................. Red
• Fan/Blower - 110 VAC.........................Plug from Fan
• Flame Controller - HI/LO solenoid..................Orange
Figure 3. Adding Fan/Blower
WARNING: LEAVE ELECTRICAL POWER OFF
AT THIS TIME. DO NOT RESTORE POWER UN-
TIL THE REMOTE CONTROL SYSTEM IS COM-
PLETELY INSTALLED.
2. Feed the electrical service wires through the Romex
clamp and secure the wires to the clamp.
3. Using the wire nuts provided, connect the service
wires to the junction box. The black wires to the black
servicewire,thewhitewirestothewhiteservicewire,
and the service ground wire to the ground stud of the
junction box.
4. Re-attach the cover plate to the outside of the fire-
place.
NOTE: Some appliances do not have a cover plate.
Instead, there is a hole through which the Romex clamp
is attached to the outer wrap.
1. Removetheelectrical cover plate from the lower side
ofthefireplace. Remove the knock-out from the plate
and attach the Romex clamp (screws to the outside)
(see Figure 1).
WARNING: TURN ELECTRICAL POWER OFF AT
THE CIRCUIT BREAKER BEFORE BEGINNING
THIS INSTALLATION.
ACCESS HOLE
COVER
PLATE
110 VAC
SERVICE
REMOTE
RECEIVER
ON/OFF
SWITCH REMOTE SWITCH
PIGTAIL
RED
RED
BROWN
RED
TH TH
WALL
SWITCH
TP TP
VALVE
REMOTE
RECEIVER Line cord
from fan
LEARN 110/120 VAC, 3A
(Receptacle on back)

3
Figure 4.
Figure 5.
VARIABLE
REGULATOR
GAS CONTROL
VALVE
FLAME CONTROL
SOLENOI
D
KNOB
SCREW
NUT
VARIABLE REGULATOR
JAM NUT
VARIABLE
REGULATOR
SOLENOID
WASHER
WASHER
PLUNGER
Installing Flame Control Solenoid
1. Removethescrewandknob from the variable regula-
tor and discard.
2. Unscrew the nut from the regulator and discard.
3. Remove the bag containing a washer and blue and
red plungers from the side of the flame control sole-
noid.
4. Place washer on flame control solenoid (see Figure 4).
5. Insert the correct plunger (blue - natural gas, red -
propane) into the flame control solenoid (see Figure 4).
6. Threadtheflamecontrol solenoidwithcorrectplunger
into the thread hole in the variable regulator. Turn
one to two turns only. Do not tighten or damage may
occur.
Wiring the Flame Controller
1. Connectthetwoleadsfrom the flame controlsolenoid
to the orange leads from the receiver.
2. Install a manometer into the pressure tap.
3. Plugtheremotereceiver into the 110/120 VACpower
supply.
4. Light the fireplace as directed in the Owner’s Manual.
5. Setthemanifoldpressureon the gas valve byrotating
the flame control solenoid.Adjust until the reading on
the manometer is 3.5 inches w.c. for natural gas, or
10.0 inches w.c. for LP.
6. Tighten the jam nut (see Figure 4) to the face of the
variable regulator body.
7. Turn the main gas knob on the gas valve OFF.
8. Remove the manometer from the pressure tap and
screw the tap closed.
NOTE: All steps required for installation of the
flame controller MUST be done by a qualified gas
service technician.
NOTE: A manometer MUST be used to set the
manifold pressure on the gas valve.
REMOTE
RECEIVER
JAM NUT
REGULATOR
TOWER
PLUNGER
RED
ORANGE
BLUE

4
The remote receiver has a 3-position slide switch: OFF/
REMOTE/ON (see Figure 6).
Figure 6. Remote Receiver
TRANSMITTER
Important:Before operating remotecontrol, transmit-
ter and receiver must have matching security codes.
See section ‘Matching Security Codes’.
Important: Review ‘Thermo-Updating/Communication-
Safety Features’ under ‘Transmitter Safety Features’
section. Communication Safety features shut down the
fireplace system when a potentially unsafe condition
exists.
Important: Review‘AutoShutdown’section.This safety
featureshutsdownthefireplaceafter9hoursofcontinu-
ous operation, in ON mode only.
Important: New or fully charged batteries are essential
forproperoperationofthemulti-functiontransmitter.The
transmitter operates on 2 AAA-size 1.5V batteries. Use
Alkaline batteries for longer battery life and maximum
operational performance.
Insert2AAA-size1.5Vbatteries into the batterycompart-
ment on the back of the transmitter. When the batteries
are correctly inserted, the screen will display numbers
(see Figure 7 for LCD Display Screen).
NOTE: If the transmitter is activated from a very cold
condition it may be necessary to allow the transmitter to
stabilize to room temperature (could take up to 15 min-
utes) before accurate room temperatures are displayed
on the screen.
NOTE: LCD screen is equipped with a “backlite” for
easier viewing of LCD screen. Backlite illuminates when
a function button is depressed.After 5 seconds elapses,
LCD screen will return to its normal state.
NOTE: The remote receiver will only respond to the
transmitter when the 3-position slide button on the
remote receiver is in the Remote position. If the
system does not respond to the transmitter on initial
use, see section Matching Security Codes.
1. With the slide switch in the ON position, the system
is on.
2. With the slide switch in the REMOTE position, the
system only operates if the remote receiver receives
commands from the transmitter.
3. With the slide switch in the OFF position, the system
is off.
NOTE:The slide switch should be placed in the OFF po-
sitionifyouwillbeawayfromyourhomeforanextended
periodoftime. Placing theswitchinthe OFF position also
functions as a safety “lock out” by turning the system off
and rendering the remote receiver inoperative.
REMOTE
RECEIVER
Line cord
from fan
LEARN 110/120 VAC, 3A
(Receptacle on back)

5
MATCHING SECURITY CODES
It may be necessary to program the remote receiver to
the security code of the transmitter upon initial use, if
batteries are replaced, or if a replacement transmitter
is purchased from your dealer. To program the remote
receiver:
1. Set the slide button on the receiver to the REMOTE
position.
2. Push the LEARN button (one beep will be heard) on
the top of the remote receiver.
3. Then press the MODE button on the transmitter.
Several beeps indicate the transmitter’s code has
been programmed into the receiver. When an exist-
ing receiver is matched to a new transmitter, the new
securitycodewilloverwritetheoldone.NOTE: When
the LEARN button is depressed, “beeping” sounds
should be heard. If no “beeping” is heard check to
see that the receiver has 110-120VAC power to it.
If you are unsuccessful in matching the security code on
the first attempt, wait 1-2 minutes before trying again.
Figure 7. Transmitter LCD Display Screen
1. LOW - Battery power low. Replace batteries within two weeks.
2. TIMER - Indicates time remaining before system shuts off, when timer-programmed, 9
- hour maximum setting.
3. MODE - Indicates operation MODE of system. ON indicates the system is on, either
manually or thermostatically. THERMO indicates the system will automatically cycle
ON/OFF, dependingon programmed SETtemperature. OFFindicates the entiresystem
is turned off.
4. SET - Indicates desired SET room temperature for THERMO operation.
5. FLAME - Single or double Flame/Hi icon indicates
burner/valve operational.
6. CLOCK - Indicates the current time in AM/PM.
7. ROOM - Indicates CURRENT room temperature.
8. ºF -Indicates degrees Fahrenheit(ºC indicatesdegrees
Celsius).
9. FAN - Indicates fan is on or programmed to come on.
Three speed settings are available.
Transmitter Settings
Flip open the plastic cover on the front of the transmitter
to expose the “SET” buttons.
NOTE: Flashing numbers on the display indicate the
system is waiting for input, such as using the UP and
DOWN buttons to program a new setting. If no change
is made to flashing digits within 15 seconds, the system
will complete the procedure last programmed and reset
the display to its normal state.
Setting the Clock
1. Press and hold the TIMER/TIME button on the trans-
mitter for more than two seconds. The hour digit(s)
will begin flashing (see Figure 7, Location #6).
2. Press the UP or DOWN button until the desired hour
is displayed in AM or PM.
3. After setting the desired hour, press and release the
TIMER/TIME button again to set the minutes; the
minute digits will begin flashing.
4. Press the UP or DOWN button until the desired min-
utes are displayed.
5. Pressandhold theTIMER/TIME buttonagainfor more
than two seconds. The time digits will cease flashing,
indicating the clock has been successfully set. You
may also press the SET button on the transmitter to
stop the time digits from flashing and set the time.
OPERATING INSTRUCTIONS
To operate the system, press the MODE button (Figure
7) on the transmitter to select the operational MODE
desired.
• ON indicates the system is on, either manually, timed
or thermostatically.
• THERMOindicatesthe system will automatically cycle
ON/OFF, depending on programmed set tempera-
ture.
• OFF indicates the entire system is turned off.
1
4
8
2
5
6
7
3
ON
OFF
FLAME
TIMER
AM
ROOM SET
F
F
THERMO
LCDDISPLAYSCREEN
MODE
SET
DOWN
FLAME
FAN
UP
TIMER
TIME

6
Figure 8. Setting Button/Child Proof Lockout
Setting ºF/ºC Scale
The factory setting for temperature is degrees Fahrenheit
(ºF). To change this setting to degrees Centigrade (ºC):
1. Removethebatterycoveronthe back of the transmit-
ter and locate the “setting button” at the top center of
battery compartment (see Figure 8).
2. Push setting button and ºF will begin flashing on the
LCD screen (see Figure 7, Location #4).
3. Push the DOWN button on the transmitter to change
ºF to ºC.
4. Push “setting button” on transmitter and Centigrade
(ºC) degree readings will display on LCD screen.
5. Repeatthisprocessto change backtoFahrenheit(ºF)
reading,thistime pushing the UPbutton. NOTE: LCD
screen will return to normal state if setting button is
not pushed within 15 seconds.
Setting Desired Room Temperature -
Thermo Operations
This remote control system can be thermostatically
controlled when the transmitter is in the THERMO
mode.(THERMOmustbedisplayedonthescreen).The
transmitter will “sense” the room temperature every two
minutes automatically turning the fireplace ON or OFF
thermostatically. To set the desired room temperature:
1. Press the MODE button to place the transmitter into
THERMO mode. THERMO ON or OFF will display.
2. PresstheUPorDOWNbuttontoselectthedesiredroom
temperature.ThehighestSETtemperatureis99ºF(32º
C). The lowest SET temperature is 45º F (6º C).
NOTE: To prevent repeated thermo-cycling of the gas
appliance,thesensingunitinthetransmitterwill only ac-
tivatetheremotereceiverwhenthe temperature change
exceeds 2º F (1º C) above or below the SET (desired)
temperature.
When the transmitter is in the THERMO mode, it should
be kept away from direct sources of heat such as fire-
places,incandescentlighting anddirectsunlight.Leaving
thetransmitterin direct sunlight, forexample,willcauseit
to read the room temperature higher than it actually is.
Setting the Countdown Timer
This remote control system can operate with a built-in
countdown timer when the transmitter is in the ON or
THERMO modes (THERMO or ON must be displayed
on the LCD screen).
1. Press and release the TIMER/TIME button on the
transmitter. The word TIMER and 0:15 flash on the
screen (see Figure 7, Location #2).
2. Press the UP and DOWN button to begin advancing
througheachof thecountdowntimeoptions.Available
countdown times are 15 min, 30 min, 45 min, 1 hour,
1 hr 30 min, and each additional half hour up to nine
hours.
3. To set the TIMER, press the SET button on the trans-
mitter. If the system is ON, it will remain on until the
“time” has expired. If the system is in the THERMO
mode,itwillcycleonandoffas the room temperature
requires until the “time” has expired.
NOTE: When the timer is used in the THERMO mode,
the THERMO operation will discontinue when the “time”
has expired.
Operating the Fan -
Operates in ON or THERMO mode
Thisremote controlsystemhas thecapabilityofoperating
a 110 VAC fan or blower system that may be included
with your gas fireplace. The fan will only operate when
thetransmitter isintheONorTHERMO mode.(THERMO
or ON must be displayed on LCD screen).
1. To turn fan ON, press and release the FAN button
on the transmitter (see Figure 7, Location #9). The
fan will operate at HI speed, and fan blade icon will
appear on LCD screen.
2. To change fan speed to MED, press and release FAN
button again. To change fan speed to LO, press and
release FAN button again.
3. ToturnfanOFF, press and release FAN button again.
Fan blade icon will disappear from LCD screen.

7
Adjusting the Flame Height -
Operates in ON or THERMO mode
This remote control system allows the user to control
the height of the FLAME when the gas valve is factory
equipped with a FLAME CONTROLLER.
1. Press and release FLAME button to change flame
height to HI (see Figure 7, Location #5), (a second
flame icon appears).
2. Press again to return flame to normal state.
Low/Battery Indicator
An “X” outlined by a battery on the right side of the LCD
screen will appear when battery power has dropped
significantly. At this time, approximately two weeks of
battery power remains.
Child Proof Lockout (CP)
The transmitter contains a “Child Proof” lockout feature
thatpreventsunauthorizeduseof the remote control. To
accessthe“ChildProof”activationbutton, remove cover
on BACK of transmitter. To activate LOCKOUT:
1. Press and hold in the “setting button” for 5 seconds.
The letters CP will display on the LCD screen (see
Figure 8). This prevents the activation of fireplace.
When any function button is pressed ON/OFF etc.
the letter CP will display on the LCD screen.
To deactivate LOCKOUT:
1. Pressandholdinthe“settingbutton”for5seconds.The
LCDwill display CPuntil5 seconds haveelapsed,and
then the LCD screen will return to its normal state.
TRANSMITTER SAFETY FEATURES
It is recommended that the TRANSMITTERS always be
located within a 20 foot operating range of the fireplace,
preferablyin the sameroomin which thefireplacesystem
is located. The TRANSMITTER features several safety
features that alert the user when the TRANSMITTER is
placed outside the 20 foot normal operating range.
Thermo-Updating and Communication-Safety Fea-
tures
This remote control has a COMMUNICATION-SAFETY
functionbuiltintoits software. It provides an extra margin
of safety when the TRANSMITTER is out of the normal
20footoperating range ofthereceiver.Itis also activated
when the batteries become weak or are removed from
the transmitter.
In the THERMO-UPDATING feature (only in the THER-
MO or TIMER modes) the transmitter normally reads
the ROOM temperature every 2 minutes. In addition to
checkingthetemperature,thetransmittersendsasignal
to the receiver indicating that the transmitter and its bat-
teries are still active.
In the COMMUNICATION-SAFETY feature, at all times
and in all OPERATING MODES the transmitter sends a
signal every fifteen (15) minutes to the receiver, indicat-
ing that the transmitter is within the normal operating
range of 20 feet.
Should the receiver NOT receive a transmitter signal
every 15 minutes (COMMUNICATION-SAFETY fea-
ture), the RECEIVER will begin a 2 HOUR (120 minute)
countdown timing function. If during this 2 hour period,
the receiver does not receive a signal from the transmit-
ter, the RECEIVER will shut down the fireplace being
controlledbythereceiver. The RECEIVER will then emit
a series of rapid “beeps”. Then, after 10 rapid “beeps”,
theRECEIVERwill continue toemitasingle “beep” every
4 seconds until a transmitter signal is again received.
The intermittent 4 second beeping will go on indefinitely
until reset.
To “reset” the RECEIVER and operate the fireplace
system:
1. Press the MODE button on thetransmitter.Theword
ON must display on the LCD screen. The COMMU-
NICATION -SAFETY operation is overridden and the
system will return to normal operation depending on
the MODE selected at the transmitter.
We recommend the user check the batteries in the
TRANSMITTER to make sure the voltage is no less
than 2.7 volts.
Auto Shutdown
ThisremotecontrolhasanAutoShutdownfeatureincor-
porated into its system. When the transmitter MODE is
inthe ON position the fireplace will continuously operate
for 9 hours. After 9 hours, the fireplace will shut down.
To relight the fireplace:
1. Press the MODE button. The fireplace will operate
continuously for up to 9 hours beforeAuto Shutdown
repeatscycle.TheAuto Shutdown signal comes from
the transmitter. The transmitter must be positioned
withina 20 footoperatingrange for theAutoShutdown
feature to operate.
SYSTEM CHECK
Millivolt Valves
Light the appliance following the lighting instructions
that came with the fireplace. Confirm that the pilot flame
is on. It must be in operation for the main gas valve to
operate.
1. Slide the 3-position button on the remote receiver to
the ON position. The main gas flame (i.e., the fire)
should ignite.
2. Slide the button to OFF. The flame should extinguish
(the pilot flame will remain on).
3. Slide the button to REMOTE (the center position),
then press the MODE button on the transmitter to
changethesystemto ON. The main gasflameshould
ignite.
4. Press the MODE button on the transmitter to change
the system to OFF. The flame should extinguish (the
pilot flame will remain on).
5. Press the MODE button on the transmitter to change
the system to THERMO.

8
6. Advancethe SET temperature on the transmitter toa
temperature of at least 2º F (1º C) above the ROOM
temperature displayed on the LCD screen and the
system flame will ignite.
7. Set the SET temperature to at least 2º F (1º C) below
theroomtemperature and the system flamewillextin-
guish. Thereafter, it should continue to cycle on and
off thermostatically approximately every two minutes
as the ROOM temperature changes, but only when
thetemperaturedifferentialbetween ROOM and SET
temperatures differs at least 2º F (1º C). The 2º F dif-
ferential is the factory setting.
Electronic Ignition System
1. Slide the 3-position button on the remote receiver to
the ON position. The spark electrode should begin
sparking to ignite the pilot (the pilot may ignite after
only one spark). After the pilot flame is lit, the main
gasvalveshould open and the maingasflameshould
ignite.
2. SlidethebuttontoOFF.Themaingasflameandpilot
flame should BOTH extinguish.
3. Slide the button to REMOTE (the center position).
4. Then press the MODE button on the transmitter to
changethesystem to ON.Thesparkelectrode should
begin sparking to ignite the pilot. After the pilot is lit,
the main gas valve should open and the main gas
flame should ignite.
5. Press the MODE button on the transmitter to OFF.
The main gas flame and pilot flame should BOTH
extinguish.
6. Press the MODE button on the transmitter to change
the system to THERMO.
7. Advance the SET temperature on the transmitter to
temperature of at least 2º F (1º C) above the room
temperature displayed on the LCD screen and the
system flame will ignite.
8. Set the SET temperature to at least 2º F (1º C) below
theroomtemperature and the system will extinguish.
Thereafter, it should continue to cycle on and off
thermostatically approximately every two minutes as
the ROOM temperature changes, but only when the
temperature differential between ROOM and SET
temperatures differ at least 2º F (1º C). The 2º F dif-
ferential is the factory setting.
This REMOTE CONTROL SYSTEM is warranted for 12
months from the date of purchase or installation to the
original purchaser to be free from defects in materials
and workmanship. Damage to the SYSTEM caused by
accident, misuse, abuse, or installation error whether
performed by a contractor, service company, or owner, is
notcovered bythis warranty. Sellerwill notbe responsible
for labor charges and/or damage incurred in installation,
Timer Operation
Thecountdown timer willoperatein either themanualON
or THERMO mode. Once the fireplace system is in an
operating mode, set the countdown timer to turn off in 15
minutes.Thetimerfunctionwillallowoperationto continue
untilthe“countdowntime”ontheLCDscreenexpires.After
15 min. elapses, the system should turn off.
repair, replacement or for incidental or consequential
damages. Batteries and any damage caused by them
are not covered by this warranty.
Some states, provinces, and nations do not allow exclu-
sionor limitationsofincidental orconsequential damages,
sothe abovelimitationsor exclusionsmay notapply.This
warranty gives you specific legal rights. You may have
other rights that vary by state, province or nation.
GENERAL INFORMATION
Transmitter Wall Bracket
The transmitter can be hung on a wall using the bracket
provided. Locate the bracket on an inside wall suffi-
ciently far away from direct sources of heat such as a
fireplace, incandescent lighting, or sunlight so it detects
ambient room temperatures, not a single heat source.
If the bracket is installed on a solid wood wall, drill 1/8”
pilot holes and install with the screws provided. If it is
installed on a plaster/wallboard wall, first drill two 1/4”
holes into the wall, then use a hammer to tap in the two
plastic wall anchors flush with the wall, then install the
screws provided.
Battery Life
Lifeexpectancyofthe batteriesinthetransmittershould
beatleast12months.Checkbatteriesannually.Whenthe
transmitter no longer operates the remote receiver from
a distance it did previously (i.e., the transmitter’s range
has decreased) the batteries should be checked.
Specifications
Batteries: Transmitter - 3V 2 ea.; AAA 1.5V, Alkaline
Remote - 110-120 VAC; 60Hz
Operating Frequency: 303.8 MHZ
FCC ID No.’s: Transmitter - K9L300ITX
Receiver - K9L3003RX
Canadian ISC ID No.’s: Transmitter - 2439 102 760
Receiver - 2439 102 760A
Service Parts List
Limited Warranty
DESCRIPTION SERVICE PART NO.
3-PRONG ADAPTER HTI-18-006
SOLENOID-110 VOLT HI/LO HTI-17-006
TRANSMITTER WALL HOLDER HTI-16-006
BATTERIES-TRANSMITTER HTI-14-006
RECEIVER HTI-13-006
TRANSMITTER (RCT-MLT-HNG) HTI-12-006-HNG
TRANSMITTER (RCT-MLT-HTL) HTI-12-006-HTL
HARDWARE PACKAGE HTI-11-006

9
Figure 9. Intermittent Pilot Ignition (IPI) Wiring Diagram
Figure 10. Standing Pilot Ignition Wiring Diagram
TRANSFORMER
3VAC
PLUG IN
RED
BATTERY PACK
THERMOSTAT
WIRE ASSEMBLY
JUMPER WIRE
(TO BROWN)
ORANGE
GREEN
VALVE
GROUND TO
FIREPLACE
CHASSIS
WHITE
ORANGE
IGNITION MODULE 3 VAC INTERMITTENT PILOT IGNITOR
HOT
NEUTRAL
I
S
THERMOSTAT
WIRE ASSEMBLY
PIEZO
WHITE
RED
VALVE
PILOT
THERMOCOUPLE

10
Figure 12. Standing Pilot Ignition Wiring Diagram
Figure 11. Intermittent Pilot Ignition (IPI) Wiring Diagram
BLACK S2
ON
OFF
ON/OFF
SWITCH
WHITE T2
RED T1THERMOPILE
GAS VALUE
BLACK S1
3/16” PIGGYBACK CONNECTOR
THERMOCOUPLE
REMOTE SWITCH
PIGTAIL
OPTIONAL WALL SWITCH,
THERMOSTAT OR REMOTE
IGNITION MODULE
3VAC
TRANSFORMER
3VAC
GRN
ORG
INTERMITTENT
PILOT
IGNITOR
IGNITION
MODULE
(3V)
ON/OFF
WALL
SWITCH
LOW VOLTAGE
PLUG-IN
3V TRANSFORMER
NEUTRAL HOT
GROUND
FLAME SPARKER/
SENSOR
REMOTE
CONTROL
SEE NOTE 1
ORG
WHT
V
ALVE
PIGGYBACK
ON/OFF SWITCH
WHITE WIRE
CAN BE
PLUGGED
INTO ANY
OF #1-#5
LOCATIONS
ON THE
NEUTRAL SIDE
BLACK WIRE CAN BE
PLUGGED INTO ANY OF
#1 - #5 LOCATIONS
ON THE HOT SIDE
BRN
BRN
VALVE
PLUG IN
GROUND TO
FIREPLACE
CHASSIS
S
I

11
Figure 14. Remote Control Standing Pilot Ignition Wiring Diagram
Figure 13. Remote Control Intermittent Pilot Ignition (IPI) Wiring Diagram
Remote Control Wiring Diagrams
V
ALVE
GREEN ORANGE
JUMPER WIRE
(TO BROWN)
PLUG IN
TRANSFORMER
3 VAC
BLACK
RED
GROUND TO
FIREPLACE
CHASSIS
WHITE
ORANGE
INTERMITTENT PILOT IGNITOR
IGNITION MODULE 3 VAC
REMOTE RECEIVER
BATTERY PACK
I
S
PIEZO
WHITE
RED
PILOT
THERMOCOUPLE
VALVE
REMOTE RECEIVER