Skytech RCAF-1035 Service manual

MODEL: RCAF-1035
INSTALLATION AND OPERATION INSTRUCTIONS
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO
NOT ATTEMPT TO INSTALL OR OPERATE
INTRODUCTION
This remote control system was developed to provide safe, reliable, user-friendly remote control system for gas heating
appliances. The system can be operated manually from the transmitter. It operates a HI/MED/LO step motor.
ON/OFF
H/M/L
WALL CLIP
SLOT
12V
BATTERY
COMPARTMENT
FRON
TB
ACK
SIGNAL
LIGHT
ON/OFF
BUTTON
HI/MED/LO
BUTTON
The transmitter operates on a 12-volt (A23) battery that is included. Install the 12V
battery supplied into the transmitter battery compartment. It is recommended that
ALKALINE batteries always be used for this product. Be sure the batterery is
installed with the (+) and (-) ends facing the correct direction.
The LED signal light should illuminate when either the ON/OFF or HI/MEDIUM/LOW
button is pressed. If the signal light does not illuminate, check the position of the
transmitter’s battery, and if the battery is fully charged.
TRANSMITTER
ON/OFF
H/M/L
1
2
KEY SETTINGS
1. ON/OFF - This turns the appliance ON or OFF.
2. H/M/L - This controls the height of the ame. It has three levels; High, Medium, Low
IMPORTANT
THE REMOTE RECEIVER SHOULD BE POSITIONED WHERE AMBIENT
TEMPERATURES DO NOT EXCEED 130º F.
RECEIVER
Install the (4) AA-size batteries supplied with the unit. It is recommended that ALKALINE batteries always be used for this
product. Be sure the batteries are installed with the (+) and (-) ends facing the correct direction.
The remote receiver has a 2-position slide switch for selecting the
mode of operation, which is OFF/REMOTE.
• REMOTE: The receiver must be in this position if you want to
use the appliance, you must use the transmitter to turn ON
the appliance. If the system does not respond to the transmit-
ter on initial use, check the battery positions in the remote. If
that does not work, see the LEARNING TRANSMITTER TO
RECEIVER section.
• OFF: Disables the remote receiver.
• It is suggested that the slide switch be placed in the
OFF position if you will be away from your home for an
extended period of time.
REMOTE
LEARN
Requires 4-AA 1.5V
alkaline batteries
Learning
button
Remote Receiver
Battery cover slides on/off
Slide
Switch
REMOTE
OFF
OFF
Skytech: RCAF-1035 REV. 5-17-16 Page 1

WIRING INSTRUCTIONS
DO NOT CONNECT REMOTE RECEIVER DIRECTLY TO 110-120VAC POWER. THIS WILL BURN OUT
THE RECEIVER. FOLLOW INSTRUCTIONS FROM MANUFACTURER OF GAS VALVE FOR CORRECT
WIRING PROCEDURES. IMPROPER INSTALLATION OF ELECTRIC COMPONENTS CAN CAUSE
DAMAGE TO GAS VALVE AND REMOTE RECEIVER.
WARNING
CONNECTING THE RECEIVER TO THE AF-LMF VALVE KIT WITH THE HI/MED/LO STEP MOTOR
• Do not install the 4-AA batteries into the receiver until the DC Step Motor is connected to the receiver.The
receiver will calibrate the step motor once the batteries are installed.
• Connect the 4-pin female connector from the DC step motor to the 4-pin male connector on the wire harness.
• Connect the 4-pin female connector on the wire harness to the 4-pin connector on the back of the receiver.
• Install the 4-AA batteries in to the receiver.
• After receiver is connected to the DC step motor using the supplied wire harness, make sure the plastic receiver
shield (Included) is located over the receiver, then locate the receiver in an area that will not exceed the 130° F. This
location will always be away from the AF-LMF, towards the front of the rebox.
Flat 4 Wire with
4 pin Female
Connector
Flat 4 Wire with
4 pin Male
Connector
Receiver Back
Flat 4 Wire with
4 pin Female
Connector
Flat 4 Wire with
4 pin Male
Connector
AFLMF
THERMO-SAFETY FEATURE
When the ambient temperature inside the receiver case reaches 130°F, the RECEIVER will automatically send power
to the step motor on the valve to shut the replace system off and the RECEIVER will begin emitting a series of four
(4) “beeps” every 2-seconds. When the ambient temperature at the RECEIVER drops between 120° F and 130° F, the
user can reactivate the replace by pushing ON/OFF button on the transmitter. When the ON/OFF button is pressed,
the THERMISTOR “resets” itself and the replace will begin operating again. However, the “beeping” will continue if the
ambient temperature remains between 120° F and 130° F. This “beeping” alerts the user that the RECEIVER should be
repositioned so the ambient temperature drops below 120° F. When the temperature drops below 120° F, and the control
is reset by pressing the ON/OFF button, the “beeping” will cease.
LEARNING TRANSMITTER TO RECEIVER
Each transmitter has a unique security code. It may be necessary to program the remote receiver to learn the security
code of the transmitter upon initial use, if batteries are replaced, or if using a replacement transmitter.
NOTE: This receiver can hold up to 3 transmitter codes. This is for the times when a second hand held transmitter or a
wall transmitter is required.
• Make sure the receiver’s slide switch is in the REMOTE position.
• Press and release the LEARN button on the receiver.
• When you hear the “Beep”, press and hold the ON/OFF or H/M/L button for about 2 seconds on the transmitter.
• You will then hear a series of rapid beeps that indicate that your new transmitter has been accepted by the receiver.
• If you press the LEARN button on the receiver and you hear no beeps, the receiver is unable to retain any more
transmitter codes (make sure that the transmitter and the receiver batteries are properly installed and fully charged).
• To delete all of the transmitter codes on your receiver, press and hold the LEARN button for 10 seconds. Then you
will hear a series of three (3) long beeps, indicating that the receiver’s memory has been cleared.
Skytech: RCAF-1035 REV. 5-17-16 Page 2

BATTERY LIFE
Life expectancy of the alkaline batteries in the transmitter and receiver should be at least 12 months. Check and replace
all batteries:
• Annually.
• When operating range becomes reduced.
• When transmissions are not received by the remote receiver.
• If the remote receiver batteries measure less than 5.3 volts (all four batteries in combination).
• If the hand held transmitter battery measure less than 9.0 volts.
TROUBLE SHOOTING
If you encounter problems with your replace system, the problem may be with either the replace itself or with the
remote. Review the replace manufacturer’s operation manual to make sure all connections are properly made. Then
check the operation of the remote in the following manner:
• Ensure all batteries are correctly installed in the transmitter and receiver. Ensure all batteries are fully charged.
• Check batteries in transmitter to make sure contacts are touching (+) and (-) ends of battery. Bend metal contacts in
for tighter t.
• Be sure receiver and transmitter are within 20 to 25-foot operating range.
• Keep receiver from temperatures exceeding 130º F. Battery life will be shortened if exposed to high temperatures.
• If receiver is installed in a tightly enclosed metal surrounding, the operating distance will be shortened.
• Make sure the hand-held transmitter and remote receiver are communicating properly (see LEARNING
TRANSMITTER TO RECEIVER section).
FCC REQUIREMENTS
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODI-
FICATIONS TO THE EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT
For Technical Service, call: U.S. INQUIRIES
[phone] or [phone]
CANADIAN INQUIRIES
[phone]
MANUFACTURED EXCLUSIVELY FOR SKYTECH II, INC
TRANSMITTER WALL CLIP
The transmitter can be hung on a wall using the clip provided.
• Wood - Drill 1/8’’ pilot holes and install with screws provided.
• Plaster/Wallboard - Drill 1/4’’ holes, tap plastic anchors in with hammer, then
install with the screws provided.
WALL CLIP
SLOT
WALL CLIP
BATTERY
COMPARTMENT
Skytech: RCAF-1035 REV. 5-17-16 Page 3
For Sales: [phone]
Web site: www.skytechpg.com