Heat & Glo T-HVBI-AUB User manual

1
Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
MODELS:
ST-HVBI-AUB
ST-HVBILP-AUB
SAI Global
Owner’s Manual
Installation and Operation
• DO NOT USE OR STORE FLAMMABLE
MATERIALS NEAR THIS APPLIANCE.
• DO NOT SPRAY AEROSOLS IN THE VICIN-
ITY OF THIS APPLIANCE WHILE IT IS IN
OPERATION.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
- If you cannot reach your gas supplier, call
the re department.
• Installation and service must be performed
by a qualied installer, service agency, or the
gas supplier.
WARNING: If the information in these
instructions is not followed exactly, a re
or explosion may result causing property
damage, personal injury, or death.
WARNING
This appliance has been supplied with an integral barrier
to prevent direct contact with the xed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other ammable
materials.
• DO NOT PLACE ARTICLES ON OR AGAINST THIS
APPLIANCE.
• Keep clothing, furniture, draperies and other ammable
materials away.
This is a room sealed appliance and no other ventilation is
required than what is provided.
DO NOT DISCARD THIS MANUAL
NOTICE
• Leave this manual with
party responsible for use
and operation.
DO NOT
DISCARD
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
WARNING! DO NOT modify this appliance.
Ref No GSCS20165
AS 4553:2008

2Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
IMPORTANT: Read all instructions carefully before starting installation.
Failure to follow these installation instructions may result in a possible re
hazard and will void the warranty. Save this manual for future reference.
MODEL ST-HVBI-AUB
SAI GLOBALAPPROVED FOR NATURAL
GAS OR PROPANE AS A BALANCED FLUE
HEATER.
Refer to the appliance data plates for gas consump-
tions and pressures.
Installation of this appliance should only be carried
out by an authorized person in accordance with the
manufacturers instructions. All relevant codes and
regulations laid down by the gas tting authorities,
municipal building regulations, electrical wiring
regulations, and the requirements of the AGA Gas
Installation Code must be observed.
This appliance and its components are tested and
safe when installed in accordance with this Installa-
tion Manual. Report to your dealer any parts dam-
aged in shipment, specically check glass condition.
The gas logs and ue system components are in
separate packages. Read all instructions before
starting installation and follow these instructions
PLEASE READ THIS MANUAL BEFORE INSTALLING AND
USING THIS APPLIANCE.
carefully during installation to ensure maximum
benet and safety. Failure to follow them will void
your warranty and may present a re hazard.
The Heat & Glo warranty will be voided by, and
Heat & Glo disclaims any responsibility for the fol-
lowing actions:
• Installation of any damaged heater or ue
system component.
• Modication of the heater or balanced ue
system installation other than as instructed by
Heat & Glo.
• Improper positioning of the gas logs or the
glass door.
• Installation and/or use of any component part
not manufactured or approved by Heat & Glo,
not withstanding any independent testing
laboratory or other party approval of such
component part or accessory.
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
Copyright 2015 • Printed in U.S.A.

3
Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
= Contains updated information.
TABLE OF CONTENTS
1.0 INSTALLATION INSTRUCTIONS...................................................................... 4
1.1 Locating the Heater ..................................................................................... 5
1.2 Framing the Heater...................................................................................... 6
1.3 Exhaust Restrictor Installation..................................................................... 9
1.4 Flue System Approvals and Installations..................................................... 10
1.5 Connecting the Gas Supply......................................................................... 22
1.6 Ignition System Wiring................................................................................. 23
1.7 Blower Wiring .............................................................................................. 24
1.8 Mantel Clearances....................................................................................... 25
1.9 Log Placement............................................................................................. 26
1.10 Installation / Removal of Optional Vanity Panel.......................................... 28
1.11 Control Module Heat Shield Instruction ...................................................... 29
1.12 Installer Testing .......................................................................................... 30
2.0 OPERATING INSTRUCTIONS.......................................................................... 31
2.1 Operation Cautions...................................................................................... 31
2.2 Safety and Lighting Information................................................................... 31
2.3 Control Module Operation ........................................................................... 33
2.4 Remote Control Operation........................................................................... 34
3.0 SERVICING AND MAINTENANCE................................................................... 39
3.1 Removal of Covers for Servicing ................................................................. 41
3.2 Removal of Components for Service........................................................... 41
3.3 Parts Replacement ...................................................................................... 41
3.4 Adjustments and Replacement Parts .......................................................... 41
3.5 Maintenance Tasks...................................................................................... 42
3.6 Troubleshooting ........................................................................................... 43
4.0 SERVICE PARTS............................................................................................... 44
Limited Lifetime Warranty................................................................................... 47


4Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
Figure 1. Diagram of the ST-HVBI-AU
1.0 INSTALLATION INSTRUCTIONS
When planning a heater installation, it’s necessary to
determine:
• Where the unit is to be installed.
• The ue system conguration to be used.
• Gas supply piping.
• Electrical wiring.
• Framing and nishing details.
• Whether optional accessories—devices such as
wall switch, or remote control—are desired.
If the heater is to be installed on carpeting or tile, or on
any combustible material other than wood ooring, the
heater should be installed on a metal or wood panel
that extends the full width and depth of the heater.
32-1/2 in.
(816mm)
36-3/16 in.
(919.3mm)
2-1/4 in.
(58mm)
4-3/4 in.
(121mm)
4-1/2”
(114mm)
4-1/16”
(102mm)
34-3/4 in.
(882mm)
4-1/2”
(114mm)
2-9/16”
(64mm)
24 in.
(610m)
9-11/16”
(245mm)
17-15/16”
(456mm)
42”
(1067mm)
ELECTRICAL
ACCESS
GAS LINE
ACCESS
Ø8”
(202mm)
12”
(306mm)46-5/8”
(1184mm)
Ø7-7/8”
(202mm)
12”
(306mm)
5-1/4”
(132mm)½”
(13mm)
FLUE COLLAR
TOP STANDOFFS
FLUE
COLLAR
TOP
LOUVER
BOTTOM
LOUVER
GAS CONTROLS
& LABELS
GAS LINE
ACCESS ELECTRICAL
ACCESS

5
Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
1.1 Locating the Heater
The diagram below shows space and clearance re-
quirements for locating a heater within a room.
Minimum Clearances
from the Heater to Combustible Materials
Figure 2. Heater Dimensions and Locations
For minimum clearances, see the direct ue termination
clearance diagrams on pages 6 and 7 in this manual.
Minimum Clearances
from the Flue Pipe to Combustible Materials
* The clearance to the ceiling is measured from
the top of the unit, excluding the standoffs (see
Figures 1 and 2).
The distance from the unit to combustible construction
is to be measured from the unit outer wrap surface to
the combustible construction, NOT from the screw
heads that secure the unit together.
mm inches
Glass Sides or Ends..........914 ................... 36
Floor ....................................0......................0
Rear Flue............................13 ................... 1/2
Metal Sides or Ends ...........13 ................... 1/2
Top ......................................64 ..................2-1/2
Ceiling* ..............................787 ...................31
mm Inches
Vertical Sections..............25 .................1
Horizontal Sections
Top .....................................76 ................. 3
Bottom ...............................25 ................. 1
Sides..................................25 ................. 1
At Wall Firestops
Top .....................................64 ..............2-1/2
Bottom ...............................13 ............... 1/2
Sides..................................25 ................. 1
Clearance Requirements
The top, back, and sides of the heater are dened by
stand-offs. The minimum clearance to a perpendicular
wall extending past the face of the heater is 1 in. (25
mm). The metal ends of the heater may NOT be
recessed into combustible construction.
914 mm
GLASS
GLASS
914 mm

6Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
A
C
B
D*
E*
A B C D * E *
42-5/8 in. 42-1/2 in. 23.2 in. 35 in. 53-3/4 in.
(1.21 m) (1.08 m) (590 mm) (889 mm) (1.37 m)
Figure 3. Framing Dimensions
* Note: These dimensions show the center
of the horizontal ue pipe. The center of
the framing hole is 1 in. (25 mm) above the
center of the ue pipe. Framing should be
constructed of 2 in. x 4 in. (51 mm x 102 mm)
lumber or heavier.
1.2. Framing the Heater
Framing can be built before or after the heater is set
in place. Framing should be positioned to accommo-
date wall coverings and heater facing material. The
diagram below shows framing reference dimensions.
CAUTION: MEASURE HEATER DIMENSIONS AND
VERIFY FRAMING METHODS AND WALL COVER-
ING DETAILS, BEFORE FRAMING CONSTRUC-
TION BEGINS.
!
WARNING: FRAMING DIMENSIONS AS-
SUME USE OF 10 MM (THICK WALL COV-
ERING MATERIALS ON EXTERIOR OF
FRAMING ONLY AND NO SHEETROCK
ON INTERIOR OF FRAMING.

7
Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
NOTES: 1. All distances are measured vertically or horizontally along the wall to a point
in line with the nearest part of the terminal.
2. Prohibited area below electricity meter or fuse box extends to ground level.
3. See clause 5.13.6.6 for restrictions on a ue terminal under a roofed area.
4. See Appendix J, Figure J1(a) and J2(a) for clearances required from a ue
terminal to a LP Gas cylinder. A ue terminal is considered to be a source of ignition.
MINIMUM CLEARANCES REQUIRED FOR BALANCED FLUE TERMINALS
OR THE FLUE TERMINALS OF OUTDOOR APPLIANCES
Figure 4
T= Flue terminal M= Gas meter Shading indicates prohibited
I= Mechanical air inlet P = Electricity meter or fuse box areas for ue terminals
f
c
n
I
openable
window
j
jj
door
h
h
h
T
e e
P
T
g
k
k
db
d
M
a
c
g
See note 2
See note 3
T
a - Below eaves, balconies or other projections: MIN. CLEARANCE - in. (mm)
Appliances up to 50 MJ/h input .................................................................................... 12 (300)
Appliances over 50 MJ/h input ..................................................................................... 20 (500)
b - From the ground or above a balcony............................................................................... 12 (300)
c - From a return wall or external corner............................................................................... 20 (500)
d - From a gas meter (M) ...................................................................................................... 39 (1000)
e - From an electricity meter or fuse box (P)......................................................................... 20 (500)
f - From a drain or soil pipe .................................................................................................... 6 (150)
g - Horizontally from any building structure (unless appliance approved
for closer installation) or obstruction facing a terminal..................................................... 20 (500)
h - From any other ue terminal, cowl, or combustion air intake .......................................... 20 (500)
j - Horizontally from an openable window, door, non-mechanical air
inlet, or any other opening into a building, with the exception of
sub-oor ventilation:
Appliances up to 150 MJ/h input .................................................................................. 20 (500)
Appliances over 150 MJ/h input ................................................................................... 59 (1500)
k - From a mechanical air inlet, including a spa blower ....................................................... 59 (1500)
n - Vertically below an openable window, non-mechanical air
inlet or any other opening into a building, with the exception of ...................................... See table
sub-oor ventilation................................................................................................................ below
CLEARANCE
Space Heaters All other appliances
Up to 50 MJ/h input Up to 50 MJ/h input Over 50 MJ/h input and
Up to 150 MJ/h input Over 50 MJ/h input
6 in. (150 mm) 20 in. (500 mm) 39 in. (1000 mm) 59 in. (1500 mm)

8Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
NOTE: PIPES OVERLAP 32 mm (1-1/4 in.) AT EACH JOINT.
Figure 5. DVP-Series Direct Flue Component Specications (127 mm (5 in.) inner pipe / 203 mm (8 in.) outer pipe)
DVP90ST
320 mm
286 mm
185 mm
32 mm
18 mm
218 mm
DVP36
DVP48
1219 mm
610 mm
914 mm
102 mm
152 mm
DVP4
DVP6
305 mm
DVP12
51 mm MIN.
DVP12A
310 mm MAX.
DVP24
251 mm
45
261 mm
DVP45
362 mm
º

9Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
1.3. Exhaust Restrictor Installation
Exhaust restrictors are recommended for these verti-
cally terminated products which have excessive draft.
Exhaust restrictors will compensate for high draft and
restore visual ame height. If the vent conguration
has a total vertical of 15 ft. - 40 ft. (4.6 m - 122 m)
an exhaust restrictor may be needed. The exhaust
restrictor can be located in the manual bag.
Exhaust Restrictor Instructions:
1. Locate the center vent hole of the air passage
on the inside rebox chamber as shown in
Figure 6.
2. Center the exhaust restrictor such that the
center hole of the restrictor aligns with the center
vent hole of the air passage inside the rebox
chamber.
3. Use (2) 1/2 in. (13 mm) self-tapping screws to
secure exhaust restrictor to the rebox air pas-
sage. See Figure 7.
4. In some applications, such as those that where
the replace is elevated off the oor, the exhaust
restrictor may be painted but painting is not
required.
NOTICE: Before painting, contact your dealer for
information on the appropriate high temperature
paint.
AIR PASSAGE
Figure 6. Air Passage Inside Firebox
EXHAUST RESTRICTOR
Figure 7. Exhaust Restrictor - Air Passage

10
Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
Figure 8. Flue System Components and Termination Kits
1.4 Flue System Approvals and Installation
A. Flue System Approvals
These models are approved to use DVP series direct
ue pipe components and terminations (see Figures 5
and 8). Approved ue system components are labeled
for identication. This pipe is tested and listed as an
approved component of the heater. The pipe is tested
to be run inside an enclosed wall. There is no require-
ment for inspection openings at each joint within the
wall. There is no required pitch for horizontal ue runs.
NO OTHER FLUEING SYSTEMS OR COMPONENTS
MAY BE USED.
Detailed installation instructions are included with each
ue termination kit and should be used in conjunction
with this Installers Guide.
The ame and ember appearance may vary based on the
type of fuel burned and the ueing conguration used.
Identifying Flue Components
The ue systems installed on this gas heater may
include one, two, or three 90° elbow assemblies. The
relationships of vertical rise to horizontal run in ue
congurations using 90° elbows MUST BE strictly
adhered to. The rise to run relationships are shown in
the ueing drawings and tables. Refer to the diagrams
on the next several pages.
This model has a 45° elbow built into it. It may be posi-
tioned to ue either horizontal or vertical. Depending on
the installation, decide which direction the elbow should
be facing. Remove the 8 screws from the corner cover
plate. Position the 45º elbow as desired and replace
the corner cover plate with the 8 screws.
HORIZONTAL TERMINATION
WALL FIRESTOPS
90º ELBOW
VERTICAL
TERMINATION
STORM COLLAR
ROOF FLASHING
PIPE LENGTH
CEILING FIRESTOP
TERMINATION KITS
DVP-TRAP2 DVP-TVHW

11 Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
Figure 9
STRAIGHT OUT
HORIZONTAL FLUEING
H
Max. Run
610 mm (24 in.)
Figure 10
V
TERMINATION CAP
H
STRAIGHT UP
VERTICAL FLUEING
V (FT.)
12.2 M MAX. (40 ft.)

12
Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
Figure 12. Flueing with One 90° Elbow
Figure 11. Flueing with One 90° Elbow
V
H
H
V
NATURAL GAS - FLUEING WITH ONE 90° ELBOW
V (FT.) H (FT.)
1’ MIN. (305 mm) 3’ MAX. (914 mm)
2’ MIN. (610 mm) 6’ MAX. (1.83 m)
3’ MIN. (914 mm) 9’ MAX. (2.7 m)
4’ MIN. (1.22 m) 12’ MAX. (3.6 m)
5’ MIN. (1.5 m) 15’ MAX. (4.5 m)
6’ MIN. (1.83 m) 18’ MAX. (5.5 m)
V + H = 40’ MAX. (12.2 m)
PROPANE - FLUEING WITH ONE 90° ELBOW
V (FT.) H (FT.)
1’ MIN. (305 mm) 2’ MAX. (610 mm)
2’ MIN. (610 mm) 4’ MAX. (1.22 m)
3’ MIN. (914 mm) 6’ MAX. (1.83 m)
4’ MIN. (1.22 m) 8’ MAX. (2.4 m)
5’ MIN. (1.5 m) 10’ MAX. (3.0 m)
6’ MIN. (1.83 m) 12’ MAX. (3.6 m)
V + H = 40’ MAX. (12.2 m)
NATURAL GAS
FLUEING WITH ONE 90° ELBOW
V (FT.) H (FT.)
1’ MIN. (305 mm) 3’ MAX. (914 mm)
2’ MIN. (610 mm) 6’ MAX. (1.83 m)
3’ MIN. (914 mm) 9’ MAX. (2.7 m)
4’ MIN. (1.22 m) 12’ MAX. (3.6 m)
5’ MIN. (1.5 m) 15’ MAX. (4.5 m)
V + H = 40’ MAX. (12.2 m)
PROPANE
FLUEING WITH ONE 90° ELBOW
V (FT.) H (FT.)
1’ MIN. (305 mm) 2’ MAX. (610 mm)
2’ MIN. (610 mm) 4’ MAX. (1.22 m)
3’ MIN. (914 mm) 6’ MAX. (1.83 m)
4’ MIN. (1.22 m) 8’ MAX. (2.4 m)
5’ MIN. (1.5 m) 10’ MAX. (3.0 m)
V + H = 40’ MAX. (12.2 m)

13 Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
Figure 13. Flueing with Two 90° Elbows
H
1
H
V
V
V
1
H
NATURAL GAS
FLUEING WITH TWO 90° ELBOWS
V (FT.) H + H1 (FT.)
1’ MIN. (305 mm) 3’ MAX. (914 mm)
2’ MIN. (610 mm) 6’ MAX. (1.83 m)
3’ MIN. (914 mm) 9’ MAX. (2.7 m)
4’ MIN. (1.22 m) 12’ MAX. (3.6 m)
5’ MIN. (1.5 m) 15’ MAX. (4.5 m)
V + H + H1 = 40’ MAX. (12.2 m)
H + H1 = 15’ MAX. (4.5 m)
PROPANE
FLUEING WITH TWO 90° ELBOWS
V (FT.) H + H1 (FT.)
1’ MIN. (305 mm) 2’ MAX. (610 mm)
2’ MIN. (610 mm) 4’ MAX. (1.22 m)
3’ MIN. (914 mm) 6’ MAX. (1.83 m)
4’ MIN. (1.22 m) 8’ MAX. (2.4 m)
5’ MIN. (1.5 m) 10’ MAX. (3.0 m)
V + H + H1 = 40’ MAX. (12.2 m)
H + H1 = 10’ MAX. (3.0 m)
NATURAL GAS
FLUEING WITH TWO 90° ELBOWS
V + V1(FT.) H (FT.)
1’ MIN. (305 mm) 3’ MAX. (914 mm)
2’ MIN. (610 mm) 6’ MAX. (1.83 m)
3’ MIN. (914 mm) 9’ MAX. (2.7 m)
4’ MIN. (1.22 m) 12’ MAX. (3.6 m)
5’ MIN. (1.5 m) 15’ MAX. (4.5 m)
V + V1 + H = 40’ MAX. (12.2 m)
PROPANE
FLUEING WITH TWO 90° ELBOWS
V + V1(FT.) H (FT.)
1’ MIN. (305 mm) 2’ MAX. (610 mm)
2’ MIN. (610 mm) 4’ MAX. (1.22 m)
3’ MIN. (914 mm) 6’ MAX. (1.83 m)
4’ MIN. (1.22 m) 8’ MAX. (2.4 m)
5’ MIN. (1.5 m) 10’ MAX. (3.0 m)
V + V1 + H = 40’ MAX. (12.2 m)

14 Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
Figure 14. Flueing with Two 90° Elbows
Figure 15. Flueing with Two 90° Elbows
H
1
V
H
V
H
H
1
NATURAL GAS
FLUEING WITH TWO 90° ELBOWS
V (FT.) H + H1 (FT.)
1’ MIN. (305 mm) 3’ MAX. (914 mm)
2’ MIN. (610 mm) 6’ MAX. (1.83 m)
3’ MIN. (914 mm) 9’ MAX. (2.7 m)
4’ MIN. (1.22 m) 12’ MAX. (3.6 m)
5’ MIN. (1.5 m) 15’ MAX. (4.5 m)
V + H + H1 = 40’ MAX. (12.2 m)
H + H1 = 15’ MAX. (4.5 m)
PROPANE
FLUEING WITH TWO 90° ELBOWS
V (FT.) H + H1 (FT.)
1’ MIN. (305 mm) 2’ MAX. (610 mm)
2’ MIN. (610 mm) 4’ MAX. (1.22 m)
3’ MIN. (914 mm) 6’ MAX. (1.83 m)
4’ MIN. (1.22 m) 8’ MAX. (2.4 m)
5’ MIN. (1.5 m) 10’ MAX. (3.0 m)
V + H + H1 = 40’ MAX. (12.2 m)
H + H1 = 10’ MAX. (3.0 m)
NATURAL GAS
FLUEING WITH TWO 90° ELBOWS
V (FT.) H + H1 (FT.)
1’ MIN. (305 mm) 3’ MAX. (914 mm)
2’ MIN. (610 mm) 6’ MAX. (1.83 m)
3’ MIN. (914 mm) 9’ MAX. (2.7 m)
4’ MIN. (1.22 m) 12’ MAX. (3.6 m)
5’ MIN. (1.5 m) 15’ MAX. (4.5 m)
V + H + H1 = 40’ MAX. (12.2 m)
H + H1 = 15’ MAX. (4.5 m)
PROPANE
FLUEING WITH TWO 90° ELBOWS
V (FT.) H + H1 (FT.)
1’ MIN. (305 mm) 2’ MAX. (610 mm)
2’ MIN. (610 mm) 4’ MAX. (1.22 m)
3’ MIN. (914 mm) 6’ MAX. (1.83 m)
4’ MIN. (1.22 m) 8’ MAX. (2.4 m)
5’ MIN. (1.5 m) 10’ MAX. (3.0 m)
V + H + H1 = 40’ MAX. (12.2 m)
H + H1 = 10’ MAX. (3.0 m)

15
Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
Figure 16. Flueing with three 90° elbows
H
H
1
H
2
V
H
V
H1
V1
NATURAL GAS
FLUEING WITH THREE 90° ELBOWS
V + V1 (FT.) H + H1 + H2 (FT.)
1’ MIN. (305 mm) 3’ MAX. (914 mm)
2’ MIN. (610 mm) 6’ MAX. (1.83 m)
3’ MIN. (914 mm) 9’ MAX. (2.7 m)
4’ MIN. (1.22 m) 12’ MAX. (3.6 m)
V+ V1+ H + H1 + H2 = 36’ MAX. (10.9 m)
H + H1 + H2 = 12’ MAX. (3.6 m)
PROPANE
FLUEING WITH THREE 90° ELBOWS
V + V1 (FT.) H + H1 + H2 (FT.)
1’ MIN. (305 mm) 2’ MAX. (610 mm)
2’ MIN. (610 mm) 4’ MAX. (1.22 m)
3’ MIN. (914 mm) 6’ MAX. (1.83 m)
4’ MIN. (1.22 m) 8’ MAX. (2.4 m)
V+ V1+ H + H1 + H2 = 36’ MAX. (10.9 m)
H + H1 + H2 = 8’ MAX. (2.4 m)
NATURAL GAS
FLUEING WITH THREE 90° ELBOWS
V + V1 (FT.) H + H1 (FT.)
1’ MIN. (305 mm) 3’ MAX. (914 mm)
2’ MIN. (610 mm) 6’ MAX. (1.83 m)
3’ MIN. (914 mm) 9’ MAX. (2.7 m)
4’ MIN. (1.22 m) 12’ MAX. (3.6 m)
5’ MIN. (1.5 m) 15’ MAX. (4.5 m)
V+ V1+ H + H1 = 36’ MAX. (10.9 m)
H + H1 = 15’ MAX. (4.5 m)
PROPANE
FLUEING WITH THREE 90° ELBOWS
V + V1 (FT.) H + H1 (FT.)
1’ MIN. (305 mm) 2’ MAX. (610 mm)
2’ MIN. (610 mm) 4’ MAX. (1.22 m)
3’ MIN. (914 mm) 6’ MAX. (1.83 m)
4’ MIN. (1.22 m) 8’ MAX. (2.4 m)
5’ MIN. (1.5 m) 10’ MAX. (3.0 m)
V+ V1+ H + H1 = 36’ MAX. (10.9 m)
H + H1 = 10’ MAX. (3.0 m)

16 Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
Figure 17. Flueing with three 90° elbows
V
H
H
1
V
1
V
H
H
1
V
1
NATURAL GAS
FLUEING WITH THREE 90° ELBOWS
V + V1 (FT.) H + H1 (FT.)
1’ MIN. (305 mm) 3’ MAX. (914 mm)
2’ MIN. (610 mm) 6’ MAX. (1.83 m)
3’ MIN. (914 mm) 9’ MAX. (2.7 m)
4’ MIN. (1.22 m) 12’ MAX. (3.6 m)
5’ MIN. (1.5 m) 15’ MAX. (4.5 m)
V+ V1+ H + H1 = 36’ MAX. (10.9 m)
H + H1 = 15’ MAX. (4.5m)
PROPANE
FLUEING WITH THREE 90° ELBOWS
V + V1 (FT.) H + H1 (FT.)
1’ MIN. (305 mm) 2’ MAX. (610 mm)
2’ MIN. (610 mm) 4’ MAX. (1.22 m)
3’ MIN. (914 mm) 6’ MAX. (1.83 m)
4’ MIN. (1.22 m) 8’ MAX. (2.4 m)
5’ MIN. (1.5 m) 10’ MAX. (3.0 m)
V+ V1+ H + H1 = 36’ MAX. (10.9 m)
H + H1 = 10’ MAX. (3.0 m)
NATURAL GAS
FLUEING WITH THREE 90° ELBOWS
V + V1 (FT.) H + H1 (FT.)
1’ MIN. (305 mm) 3’ MAX. (914 mm)
2’ MIN. (610 mm) 6’ MAX. (1.83 m)
3’ MIN. (914 mm) 9’ MAX. (2.7 m)
4’ MIN. (1.22 m) 12’ MAX. (3.6 m)
V+ V1+ H + H1 = 36’ MAX. (10.9 m)
H + H1 = 12’ MAX. (3.6 m)
PROPANE
FLUEING WITH THREE 90° ELBOWS
V + V1 (FT.) H + H1 (FT.)
1’ MIN. (305 mm) 2’ MAX. (610 mm)
2’ MIN. (610 mm) 4’ MAX. (1.22 m)
3’ MIN. (914 mm) 6’ MAX. (1.83 m)
4’ MIN. (1.22 m) 8’ MAX. (2.4 m)
V+ V1+ H + H1 = 36’ MAX. (10.9 m)
H + H1 = 8’ MAX. (2.4 m)

17
Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
HEAT
SHIELD ARROWS
ELBOW
ELBOW
SEAM
TOP VIEW
FRONT VIEW
Figure 20
B. Installing Flue Components
After determining which direction the 45º elbow will be
used follow ueing instructions accordingly.
• This heater requires the attachment of supplied 45º
elbow to unit before connection of ue components.
• To attach the elbow ue, the elbow cover plate must
rst be removed from the unit (see Figure 18).
• The elbow can be removed from the unit by aligning
the seams of the elbow to the arrows on the
surrounding heat shield (see Figure 19).
• Position the elbow in the horizontal or the vertical
position. Snap in place with the starting collar.
• Replace the elbow cover plate aligning it with the
elbow and secure in place with the 8 screws.
• Place the rope ring around the rst section of pipe
and slide it up against the cover plate.
Figure 18
ELBOW COVER PLATE
Figure 19
NOTE: The rope ring is needed for the heat manage-
ment and to prevent cold air inltration.
Fire Risk
Exhaust Fumes Risk
Impaired Performance of Appliance
• Overlap pipe slip sections at least 1-1/2
inches (38 mm).
• Use pilot holes for screws.
• Screws must not exceed one inch
long.
• Pipe may separate if not properly
joined.
WARNING

18 Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
C. Assembling Flue Components
Insert the inner ue of section A into the ared inner
ue of section B.
Start the outer ue of section A over the outer ue of
section B (see Figure 21). Note: The end of the pipe
sections with the lances/tabs on it will face towards
the appliance.
Figure 21 Figure 22
Figure 23. Seams
Note: Make sure that the seams are not aligned to
prevent unintentional disconnection.
CORRECT
INCORRECT
For elbows that are changing the ue direction, two
screws minimum should be put in the outer ue at the
joint to prevent the elbow from rotating.
A
B
Once both inner and outer ues are started, press
section A onto section B rmly until all lances have
snapped into place. Check to make sure they have
snapped together (see Figure 22) and the seams are
not aligned (see Figure 23). Tug slightly on section A
to conrm it has completely locked into place.
Note: Make sure that seams are NOT aligned to prevent
unintentional disconnection.

19
Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
10 in. (254 mm)
12 in . (305 mm)
INTERIOR
WALL SHIELD
For Vertical Runs - One restop is REQUIRED at the
hole in each ceiling through which the ue passes.
To install restops for vertical runs that pass through
ceilings:
• Position a plumb bob directly over the center of the
vertical ue component.
• Mark the ceiling to establish the centerpoint of the ue.
• Drill a hole or drive a nail through this center point.
• Check the oor above for any obstructions, such as
wiring or plumbing runs.
• Reposition the heater and ue system, if necessary,
to accommodate the ceiling joists and/or obstruc-
tions.
• Cut a 10" x 10" (254 mm X 254 mm) hole through the
ceiling, using the restop pipe opening as a guide.
• Frame the hole with framing lumber the same size
as the ceiling joists.
To install restops (heat shield) for horizontal runs that
pass through either interior or exterior walls:
• Cut a 10 in. x 12 in. (254 mm x 305 mm) hole through
the wall.
Figure 24. 254 mm x 305 mm Hole and Flue Pipe
D. Install Support Brackets
Refer to Cinch Pipe and Termination Cap installation
Instructions.
E. Install Firestops
For Horizontal Runs - Firestops are REQUIRED on
both sides of a combustible wall through which the
ue passes.
• Position the restops on both sides of the hole
previously cut and secure the restops with nails or
screws.
• The heat shields of the restops MUST BE placed
towards the bottom of the restop.
• Continue the ue run through the restop.
Note: Model DVP-TRAP2 does not need an exterior
restop on an exterior combustible wall. The restop is
built into the cap.
Note: The center of the hole is 1 in. (25 mm) above the
center of the horizontal ue pipe.
Note: There must be NO INSULATION or other com-
bustibles inside the framed restop opening.
Figure 25. Heat Shield, Interior & Exterior Firestops
TRIM HEAT
SHIELD IF TOO
LONG, ADD TO
SHIELD IF TOO
SHORT
EXTERIOR
FIRESTOP
INTERIOR
FIRESTOP
HEAT SHIELD
Figure 26. Hole & New Framing Members
CEILING
NEW
FRAMING
MEMBERS
EXISTING CEILING
JOISTS
CHIMNEY
HOLE
10" (254 mm)
10” (254 mm)

20
Heat & Glo • ST-HVBI-AUB • 2082-980 Rev. R • 9/15
If the area above the ceiling IS an attic, position and
secure the restop on top of the previously framed
hole.
Figure 29. Flueing through the Wall
Figure 28. Attic Firestop
• The termination kit should pass through the wall
restops from the exterior of the building.
F. Flue Termination
For Horizontal Terminations - To attach and secure
the termination to the last section of horizontal ue:
• The rear ue heat shield MUST be placed one inch
above the top of the ue between the wall shield and
the base of the termination cap.
• One section of the heat shield is attached to the wall
shield. The other is attached to the termination cap
in the same manner.
• The heat shield sections will overlap to match the
wall thickness (depth).
• If the wall thickness does not allow the required 1-1/2
in. (38 mm) heat shield overlap, an extended heat
shield must be used. The extended heat shield will
need to be cut to the thickness of the wall and be
attached to the wall shield.
• The small leg in the shield rests on top of the ue to
properly space it from the pipe section (see Figure 29).
If the area above the ceiling is NOT an attic, position
and secure the ceiling restop on the ceiling side of
the previously cut and framed hole.
CEILING
CEILING FIRESTOP
RAFTER
NAILS (4 REQUIRED)
JOIST
CEILING FIRESTOP
CEILING
NAILS (4 REQUIRED)
EXTERIOR
INTERIOR
Interior
Wall Shield
Inner Flue
Rear Vent
Heat Shield
1-1/2 in.
(38 mm min.)
overlap
Outer Flue
1-12 in.
38 cm min.
Overlap
Figure 27. Ceiling Firestop (Ceiling Side)
NOTE: There must be NO INSULATION or other com-
bustibles inside the framed restop opening.
NOTE: Keep insulation away from the ue pipe at least
1 in. (25 mm).