Heat & Glo SL-5 User manual

1
Heat & Glo • GLASS-5/7/9, GLASS-3X/5X/7X/9X Installation Instructions • 2372-951 Rev. F • 11/18
TOOLS
Screw gun equipped with 1/4 in (6 mm). socket or
1/4 in. (6 mm). wrench or socket
KIT COMPONENTS
(1) Left Glass Panel
(1) Right Glass Panel
(1) Rear Glass Panel
(2) Lower Glass Brackets (1 left, 1 right)
(1) Rear Lower Glass Bracket
(2) Upper Glass Brackets (1 left, 1 right)
(2) 3/8 in. (9.5 mm) Sleeves
(4) 1/2 in. (13 mm) self-tapping Screws
(2) 1-1/4 in. (32 mm) screws
(1) Top Refractory Panel (SL-X series only)
Leave this manual with party responsible for use
and operation.
Installation Instructions
1. Remove existing brick kit liner and logs from appliance,
if installed. The SL-X series ships standard with a four
piece refractory kit.
2. All Models:
Remove the screw that secures the pilot assembly to
the pilot bracket and gently pull the pilot upward about 2
inches (51 mm).
3. SL-X Series with Standard Refractory Installed:
Locate and remove the two screws that secure the rear
refractory bracket in place. See Figure 2. Retain these
screws for later use.
SL-5, SL-7, SL-9, 350X-AU, 550X-AU: Remove the two
screws adjacent to the air passage as shown in Figure 2.
CAUTION! Risk of Cuts or Abrasions. Wear protective
gloves and safety glasses during installation.
NOTICE: Handle refractory panels with care. Refractory
may chip or crack if dropped or impacted.
GLASS-5, GLASS-7, GLASS-9
GLASS-3X, GLASS-5X, GLASS-7X, GLASS-9X
Models: SL-5, SL-7, SL-9, SL-3X, SL-5X, SL-7X, SL-9X, 350X-AU, 550X-AU
Installation Instructions
CAUTION! Do not install damaged components.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
Figure 1. Metal Components - Components Shown Bent
UPPER GLASS BRACKETS
LOWER GLASS BRACKETS
REAR GLASS
BRACKET
NOTE: Install the lower glass bracket so the bend
clearance notch faces the front of the appliance.
BEND CLEARANCE NOTCH
Figure 2. Remove Screws that Secure Rear Bracket to Firebox
REMOVE SCREWS

2Heat & Glo • GLASS-5/7/9, GLASS-3X/5X/7X/9X Installation Instructions • 2372-951 Rev. F • 11/18
5. Remove the new rear lower glass bracket from the
packaging and bend the hand bend features “up” to
about 45 degrees. See Figure 4. Install the new rear
lower glass bracket with screws removed in Step 3.
Note: The new lower glass bracket spans the entire
width of the back wall of the rebox and rests above
the side lower glass brackets. See Figure 4, Detail A.
Figure 4. Bend Tabs on Lower Side and Rear Glass Brackets
6. Gently pull the pilot tube and pilot wires down,
grasping them from beneath the rebox to remove
slack in pilot wires. Reattach pilot assembly to pilot
bracket.
7. Locate, remove and discard the two screws
located below the rear exhaust hole. See Figure
5. Install the sleeve onto each 1-1/4 inch (32
mm)screw and install in holes. See Figure 6.
350X-AU, 550X-AU: These screws attach the upper
heat shield to the back of the rebox. Replace
these screws with the 1-1/4 inch (32 mm) screws
and sleeves without removing the heat shield.
Figure 5. Remove Screws
Figure 6. Install Sleeves
REMOVE SCREWS
REAR GLASS BRACKET
DETAIL A
BEND TABS UP
4. Remove lower glass brackets from packaging and
bend “up” hand bend features. See Figure 3. Install
left and right lower glass brackets by installing them
between the outer edges of the left and right hearth
pieces with the notch facing the front of the appliance.
These pieces will t tightly between the hearth sides
and the rebox. See Figure 3.
Figure 3. Install Lower Glass Bracket (Left Side Shown)
NOTCH FACES FRONT OF APPLIANCE

3
Heat & Glo • GLASS-5/7/9, GLASS-3X/5X/7X/9X Installation Instructions • 2372-951 Rev. F • 11/18
8. Locate the two upper glass brackets that are shipped
at. Bend the “Right” bracket as shown in Figure 7.
Bend the “Left” bracket shown in Figure 8.
9. Install right upper glass bracket by pushing the bracket
“up” to the rebox top and “out” to the front face of the
rebox. The front edge of the bracket should be tight
to the rebox face and the top edge of the bracket
should be tight to the rebox top. Install the bracket
by inserting the two self-tapping screws through the
bracket into the rebox. See Figure 7. Repeat step 9
for left upper glass bracket installation.
350X-AU, 550X-AU: The right and left upper glass
brackets will slide up to the top of the rebox be
tween the rebox side and the edge of the top
heat shield. Figures 7 and 8 are shown without an
upper heat shield.
Figure 7. Bend Upper Glass Brackets
(Upper Right Bracket Shown)
10. Install the rear glass panel by placing the lower edge
into the rear lower glass bracket. Ensure the smooth
side is facing toward the front of the replace. Tip
glass back until the glass touches the screw head
previously installed in step 7. Keep one hand on the
rear glass panel and proceed to step 11.
11. With one hand on the rear glass panel, bend “up”
one hand bend tab on the upper glass bracket to
approximately 90 degrees. See Figure 8. Once
the hand bend tab is properly bent, the glass panel
will not tip forward. Bend “up” the hand bend tab on
the opposing bracket. The rear glass panel is now
installed. This panel will be held in place by the side
panels once they are installed.
12. Install left glass panel by inserting the glass panel
from the front. Slide panel back until it contacts the
rear glass panel. Ensure that the tab shown below is
bent “down” on each upper glass bracket to secure
left/right glass panels. Repeat step 12 for right glass
panel installation.
Figure 8. Upper Glass Brackets Installed (Left Upper Bracket Shown)
Figure 9. Install Left Glass Panel
BEND THESE
FEATURES
SCREW HOLES
HAND BEND TAB
SUPPORT
TAB

4Heat & Glo • GLASS-5/7/9, GLASS-3X/5X/7X/9X Installation Instructions • 2372-951 Rev. F • 11/18
Please contact your Heat & Glo dealer with any
questions or concerns.
For the location of your nearest Heat & Glo dealer,
please visit www.heatnglo.com.
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.heatnglo.com
SL-X Series Only
(Not Installed on 350X-AU or 550X-AU)
Install the top refractory by holding the part horizon-
tally as shown in Figure 11. Insert the top panel into
the space between the rebox top and the top edges
of the side refractory panels as shown in Figure 12.
The refractory panel should rest on all sides of the
glass as shown in Figure 12.
Note: The refractory top panel is designed to t tightly.
It may be helpful to insert the top at a slight angle when
installing as shown in Figure 11.
13. Reinstall logs, glass assembly, and decorative front.
Figure 11. Install Top Refractory Panel
Figure 12. Top Refractory Panel
TOP REFRACTORY
PANEL INSTALLED