Heater Sports HittingStation 1 User manual

HittingStation # 1
INSTRUCTIONS
IMPORTANT
DO NOT RETURN THIS PRODUCT TO THE RETAIL STORE WHERE
PURCHASED. CALL TOLL FREE: [phone]
WARNING:
Improper use of this product can result in serious injury. Read and follow full instructions for
the proper and safe use of the HittingStation #1. Always wear a helmet with a guard. Adult
supervision is required. Inspect all aspects of the product before each use for evidence
of damage. If damaged, DO NOT USE, call our toll free number for replacement parts.
Keep area clear in front of tee and around the swinging area of the batter.
TM
®
95 West 650 South • St. George, UT 84770 • Toll Free: [phone] • [e-mail]
MODEL# HS4999
PAGE 1
Rev. Date: 09/2017

PARTS LIST
MODEL# HS4999
IF MISSING PARTS, PLEASE CALL [phone]
BATTING TEE BALL NET
PART A
Qty: 1
PART C
Qty: 1
PART D
Qty: 1
PART B
Qty: 1
PART H
Qty: 1
PART G
Qty: 1
PART F
Qty: 1
PART E
Qty: 1
95 West 650 South • St. George, UT 84770 • Toll Free: [phone] • CustomerSer[email protected] PAGE 2
PART L
Qty: 2
PART I
Qty: 1
Qty: 1
PART J
Qty: 1
PART K
Qty: 29

ASSEMBLY INSTRUCTIONS
BATTING TEE
STEP 1 - Make sure PART A’s bottom is touching ground. In the center hole
of PART A (Base), Insert PART C into the three small holes
surrounding the center hole on top of base as shown in Figure 1.
PART A
PART C
STEP 2 - Turn PART A upside down and insert PART B into the center recess
and align the lock holes with the three prongs of PART C as shown
in Figure 2.
NOTE: Align PART C prongs with the large opening of the lock
holes in PART B as illustrated in Figure 3.
PART A
PART B
PART B
Once the parts are aligned, twist PART B counter clockwise until tight.
95 West 650 South • St. George, UT 84770 • Toll Free: [phone] • CustomerSer[email protected] PAGE 3
FIGURE 1
FIGURE 2
FIGURE 3

ASSEMBLY INSTRUCTIONS
BATTING TEE (Cont.)
STEP 3 - Screw the STEM (Parts E-G) onto PART B by twisting clockwise until tight, as
shown in FIGURE 4.
NOTE: The push pin should align with the back of the BASE when fully tight-
ened and allow you to adjust the height of the tee by selecting the
various hole positions on the STEM.
FIGURE 4
STEP 4 - Push PART H (Tee Top) onto PART G (Top Stem) until it stops
as shown in FIGURE 5.
NOTE: PART H (Tee Top) is reversible and can t either way.
FIGURE 5
PART H
STEP 5 - You can now ll the BASE with sand or water to keep the
batting tee from tipping over.
After lling the BASE, push STOPPER (Part D) into the
ll hole until it snaps tight.
The HittingStation #1 Tee is now fully assembled.
95 West 650 South • St. George, UT 84770 • Toll Free: [phone] • CustomerSer[email protected] PAGE 4
PARTS E-G
PART A
PART D

95 West 650 South • St. George, UT 84770 • Toll Free: [phone] • CustomerSer[email protected] PAGE 5
WARNING: USE EXTREME CAUTION WHEN ASSEMBLING POLES AND INSERTING
INTO GROUND. FAILURE TO SECURE POLES COULD RESULT IN
SERIOUS BODILY INJURY.
STEP 1 - Remove net from box and connect pole sections. Once assembled, take each
end of pole assembly and place the bullet cap rods into the ground 8-9” to
form an arch as shown in image.
ASSEMBLY INSTRUCTIONS
BALL NET (Cont.)
STEP 2 - Slide the net over the assembled poles as shown below.
NOTE: If the bottom of the NET is not touching the ground, pull one side of the POLE ASSEMBLY out of the ground and
move closer to the other side until the NET has 3-4” of slack on the ground. You may also need to insert the pole
section deeper into the ground in order to decrease the height.
The HittingStation #1 Net is now fully assembled.
For disassembly, repeat steps backwards.
NOTE: If the ground is hard, hammer a 9 inch screw driver to create a hole, then remove,
and insert the pole section into the hole. DO NOT hammer the pole in to the
ground. You will cut the bungee and void your warranty.

***IMPORTANT SAFETY PRECAUTIONS***
95 West 650 South • St. George, UT 84770 • Toll Free: [phone] • CustomerSer[email protected] PAGE 6
1) Tee the ball up within 6-8 feet from the net - but not so close that you could hit the net with your bat. DO NOT use
this product if you are not sure of your ability to hit or throw a ball into the net.
2) NEVER allow anyone (people or pets) to stand behind the net or in any possible path of a ball should you miss the net
or should the ball go through the net.
3) DO NOT set up net where property damage could occur if the ball should miss or go through net.
4) Use common sense and all the same precautions as you would when playing baseball or softball.
5) Inspect the net before and during each use. If any rips or holes are found - DO NOT USE!
NOTE: Nylon cable ties are available from most hardware stores and can be used to repair small holes in the net. Be
aware of any new holes that may open - and if adequate repairs cannot be made, DO NOT USE!
IF YOU HAVE ANY QUESTIONS REGARDING THE USE OR SAFETY OF THE HITTING STATION #1,
CONTACT HEATER SPORTS AT 1-800-492-9334.