SRP S Series Manual

Series S Page 1 LT017 May 14, 2019
Installation, Operation and Service Instructions
INFRARED HEATER
SERIES S
WARNING FOR YOUR SAFETY
Improper installation, adjustment, alteration, service,
or maintenance can cause property damage, injury,
or death. Read the installation, operation, and service
instructions thoroughly before installing or servicing
this heater.
Do not store or use flammable vapors and liquids in the
vicinity of this or any other heater.
If you smell gas:
1. Open windows
2. Don’t touch electrical switches
3. Extinguish any open flame
4. Immediately call your gas supplier
OWNER INSTALLER
Retain this Manual & ensure available for service.
Improper installation, adjustment, alteration, service,
or maintenance can cause injury, death, or property
damage.
Read the installation, operation, and service
instructions thoroughly before installing or servicing
this heater.
Provide Manual to Owner upon completion of
installation!
Read and thoroughly understand these Instructions
before attempting any installation
563 Barton Street, Stoney Creek, Ontario L8E 5S1, CANADA
www.superiorradiant.com

Series S Page 2 LT017 May 14, 2019
CAUTION: FIRE OR EXPLOSION HAZARD
Maintain clearance to combustible constructions as further specified in this manual. Failure to do so
could result in a serious fire hazard. Heaters should not be located in hazardous atmospheres
containing flammable vapors or combustible dusts. Signs should be provided in storage areas
specifying maximum safe stacking height.
CAUTION: MECHANICAL HAZARD
This heater is designed and approved for indoor use only.
CAUTION: FIRE OR EXPLOSION HAZARD
This heater is equipped with an automatic ignition device. Do not attempt to light the burner by hand.
Failure to comply could result in a serious fire and personal injury hazard.
CAUTION: MECHANICAL HAZARD
Do not use high pressure (above 60 mbar) to test the gas supply system with the burners connected.
Failure to do so could result in damage to the burner and its control components requiring replacement.
CAUTION: SERVICE LIFE RISK
Do not install heater in atmospheres containing halogenated hydrocarbons or other corrosive
chemicals. High intensity heaters are not recommended for installation in enclosed swimming pool
areas. Failure to do so may lead to premature heater failure and will invalidate the warranty.

Series S Page 3 LT017 May 14, 2019
CONTENTS
CONTENTS.........................................................................................................................................................................3
INTRODUCTION..................................................................................................................................................................4
CODESANDREGULATIONS...............................................................................................................................................................4
GENERALSPECIFICATIONS..................................................................................................................................................5
GASSUPPLY..................................................................................................................................................................................5
ELECTRICSUPPLY............................................................................................................................................................................5
CONFIGURATION...............................................................................................................................................................5
SEALEVELRATINGS........................................................................................................................................................................5
HIGHALTITUDERATINGS.................................................................................................................................................................5
DIMENSIONALCHARTS.......................................................................................................................................................6
CLEARANCETOCOMBUSTIBLES..........................................................................................................................................7
WARNING.............................................................................................................................................................................7
LAYOUTRECOMMENDATIONS...........................................................................................................................................8
LAYOUTCONSIDERATIONS................................................................................................................................................................8
SPOTHEATING...............................................................................................................................................................................8
FULLBUILDINGHEAT......................................................................................................................................................................9
INSTALLATION..................................................................................................................................................................10
HEATERMOUNTING.....................................................................................................................................................................10
GASSUPPLY.................................................................................................................................................................................11
ELECTRIC....................................................................................................................................................................................11
TypicalWiringLayouts........................................................................................................................................................11
VENTILATION/CONDENSATION........................................................................................................................................13
VENTILATION...............................................................................................................................................................................13
CONDENSATION...........................................................................................................................................................................13
OPERATION/MAINTENENCE............................................................................................................................................14
OPERATION.................................................................................................................................................................................14
ControlOperatingSequence—DirectSparkIgnition...........................................................................................................14
ControlOperatingSequence—MillivoltPilotSystem..........................................................................................................14
ANNUALMAINTENANCE................................................................................................................................................................14
SERVICING‐TROUBLESHOOTING......................................................................................................................................15
REPLACEMENTPARTS.......................................................................................................................................................16
WARRANTY.......................................................................................................................................................................17

Series S Page 4 LT017 May 14, 2019
Important
The manufacturer’s instructions, the layout drawing, national and local codes and ordinances, and all
applicable standards which apply to gas piping and electrical wiring comprise the basic information needed to
complete the installation. These criteria must be thoroughly understood before proceeding.
Only personnel who have been trained and understand all applicable codes should undertake the installation.
SRP Representatives are Factory Certified in the service and application of this heater and can be called on
for helpful suggestions about installation.
INTRODUCTION
Superior Radiant Products is a company in the infrared heating industry founded on the principles of product quality
and customer commitment.
Quality commitments are evidenced by superior design, a regard for design detail, and an upgrade of materials
wherever justifiable.
Customer commitment is apparent through our ready responses to market demands and a never ending training
and service support program for and through our distributor network.
Superior Radiant offers more than 20 years of infrared expertise in a cost effective radiant heater design as
culmination of that commitment.
Series S model is a high intensity infrared heater.
Codes and Regulations
Installations must comply with all local building codes or in their absence; the latest edition of the national
regulations and procedures applicable to gas fired and suspended heaters.
General Installation and Gas Codes/Electrical Codes
Heaters must be installed only for use with the type of gas appearing on the rating plate, and the installation must
conform to the National Fuel Gas Code, ANSI Z.223.1 (NFPA 54) in the US and CSA B149.1 and B149.2
Installation Codes in Canada. For electrical requirements refer to the latest editions of the National Electrical Code
ANSI/NFPA 70 or Canadian Electrical Code C22.1
This heater is approved for indoor installation only.
Not for use in residential dwellings, refer to Rating plate.
Note: A residential dwelling is a domicile intended for use by one or more persons and that includes one or
more areas, such as those used for cooking, eating, living, sleeping, or a sanitary facility. A residential
dwelling does not include an attached and detached garage, workshop, or outdoors.
Aircraft Hangar Installation
Installation in aircraft hangars must conform to the Standard for Aircraft Hangars, ANSI/NFPA 409 in the US and
CSA B149.1 and B149.2 Installation Codes in Canada
Public Garages
Installation in public garages must conform to the Standard for Parking Structures, NFPA 88A or the Standard for
Repair Garages, NFPA 88B, in the US and CSA B149.1 and B149.2 Installation Codes in Canada.
Parking Structures
Technical requirements are outlined in ANSI/NFPA 88A (USA)

Series S Page 5 LT017 May 14, 2019
GENERAL SPECIFICATIONS
Gas Supply
Supply Pressure
Natural Gas:
Propane:
Minimum
6.5"W.C.
11.0"W.C.
Maximum
14.0"W.C.
14.0"W.C.
Manifold Pressure
Natural Gas:
Propane:
6.0"W.C.
10.0"W.C.
Inlet Connection ½” female NPT
Electric Supply
(Two options) 24Vac, 20 VA
Millivolt pilot system (750mVdc)
CONFIGURATION
Sea Level Ratings
Model # S3 S6 S9 S12 S16
Nominal Input
(BTU/hr)
Natural Gas 33,000 66,000 99,000 132,000 160,000
Propane 30,000 60,000 90,000 120,000 N/A
High Altitude Ratings
For Canada, 0-4500 feet above sea level. In the U.S. 0-2000 feet above sea level, anything over 2000 feet
is de-rated by 4% per thousand feet above sea level as per National Fuel Gas Code.

Series S Page 6 LT017 May 14, 2019
DIMENSIONAL CHARTS
Figure 1: Overall Dimensional Information
Model # S3 S6 S9 S12 S16
DIMENSION
in cm in cm in cm in cm in cm
A
16.3 41.4 23.1 58.7 30 76.2 36.9 93.7 36.9 93.7
B 24.4 62 24.4 62 24.4 62 24.4 62 24.4 62
C 4.2 10.7 4.2 10.7 4.2 10.7 4.2 10.7 4.2 10.7
D 12.9 32.8 19.8 50.3 26.7 67.8 33.6 85.4 33.6 85.4
E 14.8 37.6 14.8 37.6 14.8 37.6 14.8 37.6 14.8 37.6
F 16.3 41.4 16.3 41.4 16.3 41.4 16.3 41.4 16.3 41.4
G 5 12.7 5 12.7 5 12.7 5 12.7 5 12.7
H 17.1 43.4 17.1 43.4 17.1 43.4 17.1 43.4 17.1 43.4
J
15.2 38.6 22.1 56.1 29 73.7 35.9 91.2 35.9 91.2
Radiating Surface Area
in
2
cm
2
in
2
cm
2
in
2
cm
2
in
2
cm
2
in
2
cm
2
90 581 180 1161 270 1742 360 2323 360 2323
Shipping Weight
lbs Kg lbs Kg lbs Kg lbs Kg lbs Kg
36 16.4 44 20 56 25.4 64 29.1 64 29.1
Table 1: Configuration Information

Series S Page 7 LT017 May 14, 2019
CLEARANCE TO COMBUSTIBLES
The stated clearance to combustibles represents a surface temperature of 90°F (50°C) above room temperature.
Building materials with low heat tolerance (such as plastics, vinyl siding, canvas, tri-ply, etc…) maybe subject
to degradation at lower temperatures. It is the installer’s responsibility to assure that adjacent materials are
protected from degradation. A general clearance of 500 mm (20”) in every direction is recommended for
servicing. In addition to this, it is very important to observe the minimum clearances to combustibles at all times to
avoid any possibility of property damage or personal injury.
WARNING
・ Clearances as marked on the heater body must be maintained from vehicles parked beneath. Signs should be
posted identifying any possible violation of the clearance distances from the heater in all vehicle areas.
・ Maximum allowable stacking height in storage areas should be identified with signs or appropriate markings
adjacent to the thermostat or in a conspicuous location.
・ Clearances to combustibles DO NOT indicate acceptable distances from PVC paneling. Refer to panel
manufacturers recommendations.
Combustible materials are considered to be wood, compressed paper, plant fibers, plastics, Plexiglas, or other
materials capable of being ignited and burned. Such materials shall be considered combustible even though flame-
proofed, fire-retardant treated, or plastered.
Adequate clearance to sprinkler heads must be maintained.
Model Number Top Sides Rear Below
S3 35" (89 cm) 28" (71 cm) 20" (51cm) 70" (178 cm)
S6 40" (102 cm) 35" (89 cm) 20" (51 cm) 80" (203 cm)
S9 50" (127 cm) 42" (107 cm) 28" (71 cm) 100" (254 cm)
S12 54" (137 cm) 46" (117 cm) 28" (71 cm) 110" (280 cm)
S16 60" (153 cm) 48" (122 cm) 34" (87 cm) 134" (341 cm)
Table 2: Minimum clearance to combustible materials
Figure 2: Clearance to Combustibles

Series S Page 8 LT017 May 14, 2019
LAYOUT RECOMMENDATIONS
Layout Considerations
1. Because high intensity heaters are un-vented, verify local codes for guidance on air supply and dilution air.
Also see section on Ventilation.
2. Check local codes for mounting requirements and the requirement for flexible gas connectors or rigid
mounting.
3. Do not locate heaters near windy locations such as door openings.
4. Do not locate heaters in very dusty environments.
5. Avoid placing heaters below sprinkler heads or provide more than adequate clearance.
Spot Heating
High intensity heaters are ideal for spot heating applications. The following are key considerations to the
success of the application:
1. Minimize any wind in order to maximize the effect of the radiant heat.
2. Placing two smaller heaters opposing each other will be more comfortable than placing one large
heater.
3. Hang the heaters back and at an oblique angle (rather than directly overhead) in order to maximize the
exposure of the peoples’ bodies to radiant heat.
The following charts are intended for guidance only. Specific applications may require other parameters.
Suggested Minimum Mounting Heights
Heater Input Rate Mounting Angle
BTU/hr 10° 35°
ft m ft m
30,000-33,000 11 – 13 3.4 – 4.0 10 - 12 3.1 – 3.6
60,000-66,000 14.5 – 16.5 4.5 – 5.0 13 – 15 4.0 – 4.5
90,000-99,000 16 – 18.5 4.9 – 5.6 14.5 – 17 4.5 – 5.2
120,000-132,000 17.5 – 21 5.4 – 6.4 15.5 – 18.5 4.7 – 5.6
160,000 19 – 23 5.8 – 7.0 17 - 21 5.2 – 6.4
Table 3: Suggested Minimum Mounting Heights
Suggested heat loading for indoor spot heating under stated conditions:
Ambient Air
Temperature
BTU/hr per sq. ft of
Floor Area to be Heated
At 50 ft/min of wind
(15.2 m/min)
At 100 ft/min of wind
(30.5 m/min)
40°F / 4°C 150—165 165—180
55°F / 13°C 75—88 85—100
Example:
Work counter for light assembly, space is 4.5 m x 7.6 m, ambient air temperature 4C, located near shipping doors.
Approximately 540 W/m2x (4.5 x 7.6) m2= 18.5 kW
Two heaters at opposing locations would be preferred.

Series S Page 9 LT017 May 14, 2019
Full Building Heat
Calculate the total heat input required, ensuring the inclusion of any unheated make-up air due to exhaust fans.
Use the following chart as guidance to heater placement.
Model/BTUH S3
30-33,000
S6
60-66,000
S9
90-99,000
S12
120-132,000
S16
160,000
Heater
Mounting
Mounting
Angle 10°
11 - 15
(3.4 - 4.6)
15 - 20
(4.6 - 6.1)
20 - 25
(6.1 - 7.6)
25 - 30
(7.6 - 9.2)
30 - 38
(9.2 - 11.6)
Height,
ft (m)
Mounting
Angle 35°
10 - 12
(3.1 - 3.6)
13 - 16
(4.0 - 4.9)
16 - 22
(4.9 - 6.7)
18 - 26
(5.5 - 7.9)
24 - 31
(7.3 - 9.4)
Distance of first heater
row from outside wall,
ft (m)
6
(1.9)
10
(3.1)
12
(3.7)
14
(4.3)
16
(4.9)
Distance between heaters
along outside wall*, ft (m)
8 - 20
(2.5 - 6.1)
15 - 30
(4.6 - 9.2)
20 - 40
(6.1 - 12.2)
30 - 50
(9.2 - 15.2)
40 - 60
(12.2 - 18.3)
Distance between rows –
out-side wall row to next
interior row, ft (m)
30 - 60
(9.2 - 18.3)
50 - 80
(15.2 - 24.4)
75 - 110
(22.9 - 33.5)
90 - 115
(27.5 - 35.0)
100 - 125
(30.5 - 38.1)
* Distance between heaters along interior rows should be up to twice the indicated number

Series S Page 10 LT017 May 14, 2019
INSTALLATION
Heater Mounting
Figure 3 illustrates typical rigid and chain mounting configurations for the Series S heaters; verify which is
permissible by local codes.
Heaters must be hung at an angle between 10° and 35°. Typically, at the walls they are at 35° facing into the
building. The gas manifold must always be at the lower side of the heater.
Minimum 3/16" (5mm) diameter S hooks and No. 1/0 chain (200 lb./ 91 kg working load) is recommended.
Close S hooks after installation.
Never use a gas line as a hanging support and never locate gas or electric lines over the heaters.
Maintain clearance to combustibles.
Ensure that there is a plugged tap upstream of the heater or a fitting on the valve itself to verify incoming
pipeline pressure.
Do not leave the heater connected when pressure testing the pipeline. The high pressure will damage the
heater.
Figure 3: Mounting Configurations

Series S Page 11 LT017 May 14, 2019
Gas supply
Only personnel who have been trained and understand all applicable codes should undertake the
installation.
An isolation valve, or valves, has to be fitted immediately adjacent to the heater which, when closed,
allow(s) the complete burner and control assembly to be disconnected for maintenance or repair.
The gas meter and service must be sufficiently large to supply gas to the connected building’s gas load,
including the heater and any other gas fired equipment. Additionally, the gas distribution piping must be
designed according to local and national ordinances.
Before connecting burners to the gas supply system, verify that high pressure testing of the system has
been completed. Failure to do so may expose the burner components to damaging high pressure, requiring
replacement of key components.
Ensure that there is a plugged tap (⅛” NPT) upstream of the heater or a fitting on the valve itself to verify
incoming pipeline pressure.
Do not leave the heater connected when pressure testing the pipeline. The high pressure will damage the
heater.
Test and confirm that inlet pressures are correct. Refer to the heater data plate and packaging to verify fuel
type.
Electric
Figure 4 illustrates typical wiring arrangements for the Series S heater.
Two options are available: 24Vac supply (Figure 5) and Millivolt pilot system (Figure 5A).
Up to six heaters may be operated from one thermostat. (Verify thermostat electrical capacity if non SRP product
is used.)
Ensure the heaters are properly grounded.
If mechanical exhaust is used in the building, it is typical to interconnect these in the heater circuit as
shown in Figure 6.
Perform all work in accordance with local codes or the National Electric Code ANSI/NFPA 70 or Canadian
Electrical Code CSA C22.1.
Typical Wiring Layouts
In some cases the 120/24 Vac transformer can be positioned prior to the thermostat. In this case, evaluate
the contact load across the thermostat contacts, as the load created by the operating heaters may be too
great. In that case a relay should be used.
When using a transformer to power more than one heater, be sure that the control transformer being used
has a sufficient VA (volt amp) rating. Example: Operating five 24Vac model "S" heaters using one transformer
requires 20 VA per heater. 5 units x 20VA = 100VA transformer capacity minimum.

Series S Page 12 LT017 May 14, 2019
Figure 4: Typical Multi Heater Wiring Diagram
Figure 5: Wiring diagram (24 Vac - Direct Spark Ignition)
Figure 5A: Wiring diagram (Millivolt Pilot System)

Series S Page 13 LT017 May 14, 2019
VENTILATION / CONDENSATION
Ventilation
Buildings using high intensity radiant heaters require ventilation. High Intensity type heaters are considered un-
vented gas fired appliances, requiring ventilation to supply combustion air and dilute/remove the products of
combustion.
Requirements for combustion air supply and dilution air vary by jurisdiction, building type and specific installation
details. See local codes for guidance. In general, where heaters are installed without direct outside combustion
air, fresh air ventilation must be provided to building space (3 cfm per 1000 BTU/Hr in Canada, 4 cfm per 1000
BTU/Hr in the USA). Verify applicable local codes in the USA as requirements change by jurisdiction.
Mechanical exhaust should be electrically interconnected with the heaters and should always be installed in
conjunction with inlet air openings. See “Block Diagram for Interconnecting Fan/Humidistat” above for
details.
Inlet air opening should be relatively small and distributed over the operating area of the heaters. They
must always be located below the level of the heaters. One square inch of net free inlet area per 1000
BTUH is recommended.
Figure 6: Block Diagram
Condensation
The products of combustion for natural gas contain up to 1 liter of water per 100,000 BTU consumed.
This may add substantial amounts of moisture to the building air environment and may become a
problem of condensation on cold surfaces within the building. This is particularly true for poorly insulated
metal roof decks or structural steel framing.
To decrease condensation, increase mechanical ventilation.
Ensure that continuous waterproof barriers are used on the inside of all insulated surfaces.
Ensure that exhausters pull air from the entire space and across the condensing surface.
Humidistat controls may be integrated into the electrical control circuit of the heaters.
When using a humidistat to control exhaust
fans, wire the humidistat to cause the fan to
operate on humidity rise, NOT humidity fall.
Depending on fan horsepower, a relay may or
may not be needed.

Series S Page 14 LT017 May 14, 2019
OPERATION / MAINTENENCE
Operation
Ensure the gas supply line has been purged.
Open all gas cocks to the heaters and electrically energize the system.
Follow the instructions on the heaters Lighting Instructions Label. Check to ensure that the
thermostat starts and shuts down the system.
Control Operating Sequence—Direct Spark Ignition
1. The thermostat calls for heat.
2. The ignition module, after a pre-purge period of approximately 30 seconds, energizes the igniter.
Additionally, the gas valve is energized for this ignition trial period of 15 seconds.
If a flame is detected, the ignition sensing rod "reads" a rectification signal and the gas valve remains
open. The sparking stops when the flame signal is established.
If no flame is detected, the gas valve closes and a 30 sec inter-purge period begins. After the inter-
purge, the module repeats the trial for ignition period. If flame is still not established, a second and final
inter-purge followed by a final ignition trial cycle begins. After three trials, the module will lockout for a
period of approximately 1 hour or until reset (reset is accomplished by removing power from the
module for at least 5 seconds). After this 1-hour period, the module re-attempts the full ignition
sequence.
3. Once operating, the heater will continue to do so until the thermostat is satisfied; shutting off the gas valve.
Control Operating Sequence—Millivolt Pilot System
Lighting Instructions
1. Set the thermostat to the lowest setting.
2. Turn off all electric power to the appliance.
3. Push in gas control knob slightly and turn clockwise to "off".
4. Wait (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, stop!
And follow safety information. If you don't smell gas, go to the next step.
5. Turn knob on gas control counter clockwise to "pilot". Push in control knob all the way and hold in.
Immediately light the pilot with a match.
6. Continue to hold the control knob in for about one (1) minute after the pilot is lit. Release knob and it will
pop back up. Pilot should remain lit. If it goes out, repeat steps 4 through 7.
• If knob does not pop up when released, stop and immediately call your service technician or gas
supplier.
• If the pilot will not stay lit after several tries, turn the gas control knob to "off" and call your service
technician or gas supplier.
7. Turn gas control knob counter clockwise to "on".
8. Turn on all electric power to the appliance.
9. Set thermostat to desired temperature.
Shut Down Instructions
1. Turn down thermostat.
2. Turn off electric power to the appliance.
3. Push in gas control knob slightly and turn clockwise to "off". Do not force.
4. Wait 5 minutes before attempting to re-light.
Annual Maintenance
1. Close the fuel gas valve and de-energize electrical power to the heater.
2. With an air hose regulated to no more than 15 psig blow away accumulated dust. Blow across
the face of the ceramic tiles, not directly at them. Blow into each venturi for about one minute.
3. Verify that there are no cracked tiles.
4. Review the wiring for any loose connections.

Series S Page 15 LT017 May 14, 2019
SERVICING - TROUBLESHOOTING
Symptom Possible Cause Corrective Action
Heater will not turn off Defective thermostat
Stuck solenoid valve
Repair or replace
Repair or replace
Gas Odor Loose pipe connection Verify all connections are sealed
by using an appropriate leak test
Burning of gas/air mixture
inside venturi (flashback)
Cracks between or across ceramic grids
Excessive drafts
Replace burner head assembly
Shield or relocate heater
Heater Cycles on/off
Excessive drafts
Flame sense not grounded
Low gas pressure
Shield or relocate heater
Verify wiring and correct
Verify and correct
Low surface temperature on
ceramic surface
Dirty or plugged ceramics
Low inlet gas pressure
Misaligned manifold/orifice
Insufficient gas supply
See cleaning maintenance
Verify and correct
Replace manifold
Verify capacity of fuel supply lines
No spark, no ignition
No power to control module
Control module defective
No power to spark electrode
No heater ground

Verify and correct/replace
Heater sparks, but will not
light
No gas supply
Defective gas valve solenoid
Defective electronic control
Check shut off valve and
combination gas valve
Verify and correct/replace
Heater lights, but ‘locks out’
after about 15 seconds
Poor ground
Reversed polarity on electric supply
Sense electrode not sensing flame
Defective electronic control
Verify and correct/replace
Check continuity of sense
electrode
Verify and/or replace

Series S Page 16 LT017 May 14, 2019
REPLACEMENT PARTS
Figure 7: Replacement Parts
Millivolt Pilot System Replacement Parts Only
P/N DESCRIPTION
SG012 NAT GAS VALVE
SG037 LP GAS VALVE
SG016 POWERPILE Q313A1022
SG017 PILOT ASS’Y (NAT) Q314A3679
SG018 PILOT ORIFICE (LP) #390686-1

Series S Page 17 LT017 May 14, 2019
Warranty
SERIES S INFRARED HEATERS
WARRANTY
The Manufacturer warrants to the original owner that the product will be free of defects in
material and workmanship. For the Series S, the warranty for all components except for the
ceramic burner head assembly is limited to 24 months from the date of installation. The ceramic
burner head assembly shall be warranted for an additional eight years for units which are proven
to the satisfaction of the manufacturer to be inoperative due to defects in material or
workmanship.
The Manufacturer’s obligation under this warranty is limited to repair or replacement, F.O.B. its
facility, of the defective part. In no event shall the manufacturer be liable for incidental expense
or consequential damages of any kind.
This warranty does not cover any shipping, installation or other labor costs incurred in the
repair or re-placement of the product. No materials will be accepted for return without
authorization.
This warranty will not apply if in the judgment of the Manufacturer the heater has been
improperly in-stalled, unreasonably used, damaged, or modified.
This warranty will not apply to damage to the product when used in corrosive atmospheres and
in particular atmospheres containing halogenated hydrocarbons. No person is authorized to
assume for the Manufacturer any other warranty, obligation or liability.
THE REMEDIES PROVIDED FOR IN THE ABOVE EXPRESS WARRANTIES ARE THE
SOLE AND EXCLUSIVE REMEDIES. NO OTHER EXPRESS OR IMPLIED WARRANTIES
ARE MADE INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE.
ADDRESS QUESTIONS TO YOUR LOCAL DISTRIBUTOR
Heater Series :__________________________
Installed Rate :_____________________Btu/hr
Serial Number :__________________________
Installed Date :__________________________