Heath Zenith 5105 User manual

© 2008 HeathCo LLC 598-1102-06
Model 5105
Motion Sensor
Light Control
TEST
2 Shells
Features
• Creep Zone™ Technology.
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• DualBrite®Timer.
• Photocell keeps the lighting off during daylight hours.
• LED indicates motion was sensed (day or night).
TEST 1 5 20
ON-TIME
Off 3 6 Dusk to
Dawn
DualBrite®
Put ON-TIME switch
on the sensor bottom
toTEST and the Dual-
Brite®switch OFF.
OPERATION
* resets to Auto Mode at dawn.
ON-TIME
TEST 1 5 20
... back on.
1 Second OFF
then...
Put the ON-TIME switch in the 1, 5,
or 20 minute position.
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flipthelightswitchoff foronesecond
thenbackontotogglebetweenAUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 20
position.
Note: When first turned on wait about 1 1/2minutes for
the circuitry to calibrate.
This package includes:
Light Control
Sensor
Cover
Plate
Bulb
Holders
Plastic Hanger
Rubber Plug
Gasket
6 Screws
(3 sizes included)
Mounting Strap
Mounting Bolt
2 Wire
Connectors
Requirements
• The light control requires 120-volts AC.
• If you want to use Manual Mode, the control must be
wired through a switch.
• Some codes require installation by a qualified
electrician.
• This product is intended for use with the enclosed
gasket and with a junction box marked for use in wet
locations.
Mode: On-Time Works: Day Night
Test 5 Seconds x x
Auto 1, 5, or 20 Min x
Manual To Dawn* x
Accent 3, 6 Hr, to Dawn x
AUTO
MANUAL MODE

2598-1102-06
INSTALLATION
For easy installation, select an existing light with a wall
switch for replacement.
For best performance, mount the fixture about 8 ft.(2.4 m)
above the ground. NOTE: If fixture is mounted higher than
8 ft.(2.4 m), aiming the sensor down will reduce coverage
distance.
For eave mount only:
❒Swing the sensor head towards the clamp screw
joint.
If the sensor pops out of the ball joint, loosen the
clamp screw and push the sensor back into the ball
joint. Tighten the clamp screw when done.
❒Then rotate the sensor head clockwise 180° so the
controls face down.
Wall Mount Eave Mount
For under eave installation, the sensor head must
be rotated as shown in the next two steps for proper
operation and to avoid the risk of electrical shock.
DualBrite®Timer
Light comes on half bright for selected time after dusk
(Off, 3 hr., 6 hr., until dawn). Selecting OFF disables
this feature. The motion sensing features will continue
to work as described in this manual.If motion is sensed,
the light turns on full bright for the ON-TIME (1, 5, or
20 minutes) then returns to dim mode.
Move ON-TIME Switch to
1, 5, or 20 minutes
Mode Switching Summary
Flip light switch off
for one second then
back on*
MANUAL MODE
AUTO
TEST
* If you get confused while switching modes, turn the
power off for one minute, then back on. After the cali-
bration time the control will be in the AUTO mode.
Controls
Clamp Screw
Controls
Controls

3
598-1102-06
❒ Remove the existing light fixture.
❒Installthemountingstrapasshownusingtwoscrews
that fit your junction box.
❒The plastic hanger can be used to hold the fixture
while wiring. The small end of the plastic hanger
can be threaded through the hole in the center of
the cover plate. The small end then goes into one
of the slots on the mounting strap.
❒ Route the light control’s wires through the large
gasket holes.
❒Twistthejunctionboxwiresandfixturewirestogether
as shown. Secure with wire connectors.
White to
White
Black to
Black
Junction box ground wire to
green ground screw on fixture.
Gasket
Mounting
Strap
Mounting
Bolt
Rubber
Plug
Mount the Light Control
❒Align the light control cover plate and cover plate
gasket. Secure with the mounting bolt.
❒Align the three slots in the decorative shell with the
bulb holder pins. Push the shell in and then twist
clockwise to lock. Repeat for other shell.
Lock Nut
To avoid water damage and electrical shock,
keep bulb holders 30° below horizontal.
❒ Adjustthebulbholdersbylooseningthelocknutsbut
do not rotate the bulb holders more than 180° from
thefactorysetting.Whenscrewinginthe floodlamps,
do not overtighten.
Keep bulbs at least
1" (25 mm) from the
sensor.Do not allow
the bulbs to block
the lens.Lens
❒Push the rubber plug firmly into place.
❒If a wet location junction box was not used, caulk
the wall plate mounting surface with silicone
weather sealant.
Wire the Light Control
WARNING: Turn power off at circuit breaker
or fuse.
Shell Slot

4598-1102-06
❒Loosen the clamp screw in the
sensor ball joint and gently
rotate the sensor.
❒Walk through the coverage
area noting where you are
when the lights turn on (also,
the LED will flash several times
whenmotionisdetected).Move
the sensor head up, down, or
sideways to change the cover-
age area. Keep the sensor at
least 1" (25 mm) away from
the bulbs.
❒Adjust the RANGE as needed.
RANGE set too high may
increase false triggering.
❒Secure the sensor head by
tightening the clamp screw.
Do not overtighten the screw.
❒Set the amount of TIME you want the lights to stay
on after motion is detected (1, 5, or 20 minutes).
❒Set the DualBrite®switch to the amount of time after
dusk you want the lights on at low level (Off, 3, 6
Hrs., Dusk-to-Dawn).
Clamp
Screw
Ball
Joint
Aim Sensor
Down for Short
Coverage
Aim Sensor
Higher for Long
Coverage
WARNING - Risk of fire. Do not aim the bulbs
at a combustible surface within 3 ft. (1 m).
Bottom of Sensor
Avoid aiming the sensor at:
• Objects that change temperature rapidly, such as
heating vents and air conditioners. These heat
sources could cause false triggering.
• Areas where pets or traffic may trigger the control.
• Nearby large, light-colored objects reflecting light
may trigger the shut-off feature. Do not point other
lights at the sensor.
MAX
MIN
RANGE
ON-TIME DUAL BRITE™
TEST 1 5 20
MINUTES
OFF 36DUSK TO
DAWNHOUR
C
R
E
E
P
Z
O
N
E
™
B
O
O
S
T
Maximum
Maximum Range Coverage Angle
Motion
Motion
15 ft.
(4.6 m)
70 ft. 100 ft.
(21 m) (30.5 m)
Boosted
Sensor
240°
Least Sensitive Most Sensitive
NOTE: Iffixtureismountedhigherthan8ft.(2.4m),aiming
the sensor down will reduce coverage distance.
The detector is less sensitive to motion directly towards it.
Creep Zone™
Creep Zone™
Creep Zone™ Creep Zone™
NOTE: Creep Zone™ is a new zone of detection
which was added as an option to select Heath®/Zenith
motion sensing products. This feature adds a zone
of detection under the motion sensor. Creep Zone™
requires no additional adjustment and operates in
conjuction with the forward-looking sensor.
TEST AND ADJUSTMENT
❒Turn on the circuit breaker and light switch.
NOTE: Sensor has a 1 1/2minute warm up period
before it will detect motion. When first turned
on, wait 1 1/2minutes.
❒Turn the RANGE control to the medium position
(halfway betweenMINandMAX),DualBrite®toOFF,
and the ON-TIME control to the TEST position.

5
598-1102-06
SPECIFICATIONS
Range . . . . . . . . . . . . Up to 70 ft. (21 m); 100 ft.
(30.5m)withRangeBoost.[varies
with surrounding temperature]
Vertical Range . . . . . . Up to 15 ft. (4.6 m)
Sensing Angle . . . . . . Up to 240° horizontal. Up to 80°
Vertical
Electrical Load. . . . . . Up to 300 Watt Maximum In-
candescent [Up to 150 Watt
maximum each bulb holder.]
Power Requirements . 120 VAC, 60 Hz
Operating Modes. . . . TEST, AUTO and MANUAL
MODE
Time Delay . . . . . . . . 1, 5, 20 minutes
DualBrite®Timer . . . . 3, 6 hours, Dusk-to-Dawn
HeathCo LLC reserves the right to discontinue prod-
ucts and to change specifications at any time without
incurring any obligation to incorporate new features
in products previously sold.
TROUBLESHOOTING GUIDE
SYMPTOM POSSIBLE CAUSE SOLUTION
Lights will not come
on.
1. Light switch is turned off.
2. Flood lamp is loose or burned out.
3. Fuse is blown or circuit breaker is turned off.
4. Daylight turn-off is in effect.
5. Incorrect circuit wiring, if this is a new installation.
6. Light control aimed in wrong direction.
1. Turn light switch on.
2. Check flood lamp and replace if burned out.
3. Replace fuse or turn circuit breaker on.
4. Recheck after dark.
5. Verify wiring is correct.
6. Re-aim light control to cover desired area.
Lights come on in day-
light.
1. Light control may be installed in a relatively dark
location.
2. Light control is in TEST.
1. The fixture is operating normally under these condi-
tions.
2. Set control switch to 1, 5, or 10 minutes.
Lights come on for no
apparent reason.
1. Light control may be sensing small animals or auto-
mobile traffic.
2. Range is set too high.
3. DualBrite®timer is on.
1. Re-aim light control.
2. Reduce range.
3. The fixture is operating normally under these condi-
tions.
Lights turn off too late in
Dusk-to-Dawn setting.
Light control may be installed in a relatively dark loca-
tion.
Relocate light control, or use 3 hr. or 6 hr. setting.
Lights stay on continu-
ously.
1. A flood lamp is positionedtooclose to the light control
or pointed at nearby objects that cause heat to trigger
the light control.
2. The light control may be picking up a heat source
like an air vent, dryer vent, or brightly painted, heat-
reflective surface.
3. Light control is in manual mode.
1. Reposition the flood lamp away from the light control
or nearby objects.
2. Reduce range.
3. Switch light control to AUTO.
Lights flash on and off. 1. Heat or light from the flood lamps may be turning the
light control on and off.
2. Heat being reflected from other objects may be turn-
ing the light control on and off.
3. Light control is in the TEST mode and warming up.
4. Light may be leaking through the flood lamp reflec-
tors.
1. Reposition the flood lamp away from the light con-
trol.
2. Reposition light control.
3. Flashing is normal under these conditions.
4. Replace the flood lamps with new high quality PAR
38 lamps. (Make sure the metal lamp protectors are
installed).
Lights flash once, then
stay off in manual
mode.
Light control is detecting its own lights. Reposition flood lamps to keep area below the light
control relatively dark.