Heatilator Gas Fireplace NDV3630I User manual

1
Heatilator • SIM-3630, SIM-3933, SIM-4236, SIM-4842 Decorative Front Instructions • 2382-930 Rev. B • 9/17
SIM-3630, SIM-3933, SIM-4236, SIM-4842
Installation Instructions
Leave this manual with party responsible for use
and operation.
WARNING! Risk of Fire! Combustible materials MUST
NOT overlap or be placed under a surround.
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
CAUTION! Do not install damaged components.
WARNING! Risk of Fire! DO NOT apply combustible ma-
terials beyond the minimum clearances. Comply with all
minimum clearances to combustibles as specied. Over-
lapping materials could ignite and will interfere with proper
operation of doors and louvers.
CONTENTS:
• Decorative Front Assembly
• Shoulder Screws (2)
• Installation Instructions
PREPARATION:
• Verify and remove contents from packaging before be-
ginning installation.
• Refer to cleaning instructions on page 3.
For Models:
NDV3630I-B, NDV3630IL-B, NDV3933I-B,
NDV3933IL-B, NDV4236I-B, NDV4236IL-B,
NDV4236I-NVR, NDV4842I-B, NDV4842IL-B
NBV3630I-B, NBV3933I-B, NBV4236I-B, NBV4842I-B
NNXT3933IF-B, NNXT3933ILF-B, NNXT4236IF-B,
NNXT4236ILF-B
TOOLS REQUIRED:
• 1/4 inch drill driver with 1/4 hex bit
Proceed to “Install Hood.”
For the models listed below, it will be necessary to
remove the lower magnet latches and replace with a
shoulder screw:
NDV3630I,NDV3630IL,NDV3933I,NDV3933IL,
NDV4236I, NDV4236IL, NDV4842I, NDV4842IL
NBV3630I, NBV3933I, NBV4236I, NBV4842I
NNXT3933IF, NNXT3933ILF, NNXT4236IF,
NNXT4236ILF
TOOLS REQUIRED:
• 1/4 inch drill driver with #2 Phillips bit and 1/4 hex bit
1. Locate the magnetic latches in the bottom corners of
the appliance. Using a #2 Phillips bit, remove the two
screws retaining both latches. See Figure 1.
Figure 1. Remove Screws from Magnetic Latches
CONTENTS:
• Decorative Front Assembly
• Hood
PREPARATION:
• Verify and remove contents from packaging before be-
ginning installation.
• Refer to cleaning instructions on page 3.

2Heatilator • SIM-3630, SIM-3933, SIM-4236, SIM-4842 Decorative Front Instructions • 2382-930 Rev. B • 9/17
INSTALL HOOD (All Models)
1. Locate the four screws inside the upper section of the
appliance.
2. Loosen and partially unscrew all four screws about 1/8
inch using a 1/4 inch drill driver.
3. Slide the hood into position under the screw heads.
See Figure 3.
4. Using a 1/4 inch drill driver, tighten the four screws. Do
not overtighten.
Figure 3. Install Hood
2. Install a shoulder screw in the outermost hole from
where the latches were removed. See Figure 2.
Shoulder screws are located in the manual bag. Tight-
en shoulder screw until snug. Do not overtighten.
Figure 2. Install Shoulder Screw (1 Per Side)
OUTERMOST LATCH HOLE

3
Heatilator • SIM-3630, SIM-3933, SIM-4236, SIM-4842 Decorative Front Instructions • 2382-930 Rev. B • 9/17
Cleaning Instructions for Decorative Fronts
Use a microber cloth and Windex® Original Glass
Cleaner or 03M003 Stove Bright® Glass Cleaner to
clean the decorative front immediately after installation
to remove acids deposited by the installer or technician.
Spray the cleaner onto the microber cloth and carefully
wipe the entire surface. The decorative front should
be cleaned in this manner annually by the homeowner
to remove ngerprints or other contaminants. Once
oxidation of the paint pigment has occurred, cleaning will
not restore the original color.
Please contact your Heatilator dealer with any questions
or concerns.
For the location of your nearest Heatilator dealer,
please visit www.heatilator.com.
Heatilator, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.heatilator.com
1. Check that the hanging brackets are bent to an ap-
proximate 90 degree angle as shown in Figure 4.
Figure 5. Hang Decorative Front on Shoulder Screws
Figure 4. Hanging Hooks Bent Correctly
INSTALL THE SIMON DECORATIVE FRONT
(All Models)
UPPER
LOWER
SHOULDER SCREWS
2. Install the decorative front by hanging it on the four
shoulder screws on the appliance. See Figure 5.
Note: It may be necessary to adjust the hanging brackets
slightly to make the decorative front hang squarely
in the appliance opening.