Heatilator I80 User instructions

28-1/2"
[724]
55-1/2"
[1410]
effective height
49-1/8"
[1248]
49-5/8"
[1260]
59-1/4"
[1505]
7-5/8"
[194] 42" [1067]
Gas
Knockout
18-1/2"
[470]
8-5/8"
[219]
Gas
Knockout
8-5/8"
[219]
9-5/8"
[244]
9-1/2"
[241]
9-1/4"
[235]
Outside
Air
34-1/2"
[876]
9-1/2"
[241]
27-1/2"
[699]
50-1/2"
[1283]
Top View
Front View
Left Side View Right Side View
*Header must be installed after unit
* Framing must be filled in to top of front
standoff after unit is installed.
Specifications
Additional information can be found online at www.heatilator.com or www.fireplaces.com
I80
Please consult the manufacturer’s
installation manual for all details and
requirements before making a final
design layout decision.
Icon I80
42" Wood Fireplace
MODEL FRONT WIDTH BACK WIDTH HEIGHT DEPTH FIREPLACE OPENING
I80 Actual Framing Actual Framing Actual
Rough
Opening
Framing*
Actual Framing 42 x 28-1/2
50-1/2 51-1/2 34-1/2 51-1/2 59-1/4 59-3/4 27-1/2 28-1/2

CLEARANCES TO COMBUSTIBLES
FRAMING DIMENSIONS
MANTEL LEG/WALL PROJECTIONS
HEARTH EXTENSION CONSTRUCTION
APPLIANCE LOCATION
MANTEL PROJECTIONS
HEARTH EXTENSIONS
65-5/8" [1667]
46-3/8"
[1178]
21-1/2"
[546]
51-1/2"
[1308]
1/2" [13] all
configurations
In an exterior
chase or projecting
into a garage
Across a
corner
As a
room
divider
Along a wall
59-1/2"
[1511]
51-1/2"
[1308]
28-1/2"
[724]
28-1/2"
[724]
28-1/2"
[724]
59-1/2" [1511]
51-1/2" [1308]
59-1/2" [1511]
51-1/2" [1308]
48"
[1219]
min.
24"
[610]
24"
[610]
92-3/4"
[2356]
24"
[610]
**28-1/2"
[724]
51-1/2"
[1308]
Header MUST NOT
be notched!
*8"
[203]
* 4"
duct. Extra space needed for outside
air connection. If outside air duct has
no bend, this dimension may be reduced
as long as minimum clearances are met.
Header will sit on
top of front stand
offs after fireplace
is installed.
** If interior of chase will be drywalled,
add the thickness to this measurement
2" [51]
17"
[432]
42" [1067]
24"
[610]
24"
[610]
19-3/4"
[502]
22-3/8"
[568]
FLUSH
FRONT
4"
[102]
BRICK
FRONT
50° angle
39° angle
Grid represents
1" scale
50-1/2" [1283]
2" [51]
required
Continuous,
non-combustable
sealant
Tile, stone or other
non-combustible
material
Floor constructed of
wood or other combustible
material
HX4 Hearth Ext
or equivalent insulation.
See install manual
Fireplace
Protective
Metal Hearth
Strip
66" [1676] 20"
[508]
12"
[305]
(insulation)
0" to level of
standoffs
Attic
Insulation
Shield
(ceiling)
(roof)
(attic)
(ceiling)
Ceiling Firestop
Offset/Return (secured
with hanger straps)
Storm Collar
Roof Flashing
Back & sides of unit
1-1/2" [38] (except at nail
flanges where it is
1/2" [13]
Must have 2" [51] minimum
clearance to header
0" to floor
2" [51] min.
Shaded areas represent
2" [51] minimum air space
clerance required around
pipe.
Combustible Object
48"
[1219]
Adapter attached here (not shown)
7 ft [2134]
minimum base
of fireplace
to ceiling
Combustible Wall
2 x 4 stud wall
Standoffs
Measured from top of
fireplace opening
12" [305]
12" [305]
minimum
1-1/2" [38]
maximum
6" [152]
mimimum
Combustible
Decorative Facing
Seal joint with
non-combustible
sealant
Noncombustible
Decorative Facing
such as: stell, iron,
brick, tile, concrete,
slate, glass, plasters
1/2"
[13]
Fireplace must be set out
1/2 [13] in front of the face
of the framing material.
Specifications
WS/HTL/I80_0615
Additional information can be found online at www.heatilator.com
PRODUCT LISTING CODES
US UL 127
CAN ULC-S610
Product information provided is not
complete and is subject to change without
notice. Product installation must adhere
strictly to instructions accompanying
product to avoid risk of fire and potential
injury.
Lakeville, MN Phone: [phone]
Web: www.heatilator.com
I80