Heatmiser PRTHW-W User manual

Model: PRTHW-W
REF: PRTHW-W
Revision 1.1 12/11

1
Contents Page
Install Procedure 2-3
Pairing the Thermostat 4-7
Icons Explained 8
Temperature Display 9
Seng the Clock 9
Locking the Thermostat 10
Seng the Comfort Levels 11-13
Seng the Hot Water Switching Times 13
Hot Water Override 14
Temperature Hold 14
Turning the Heang On/Off 15
Holiday Feature 16
Factory Reset 17
Oponal Feature Setup 18-25

2
$()"")%$'%*'

%+$***(#%)***/","4

$()"")%$

(+""/)&(**(%$*"%*
*(#%)**(%#*!&"*/&"$
)#"""**(#$"(,($*%*)"%*)
%$*%**%#%**(#%)**4


.*!&"**%*-""4"&*(%$*%
**(#%)***%*!&"*4




@

3
$()""$)))'(
@**()()+&&"-***(#%)**4


%))***(/%"(1&+)$
(")*%#&(*#$*%%(9"%*%$
*%**%#%**(#%)**:

$)*""***()$*%"(1%""%-$
*&%"(*/%***()4$&+)*
%"(!$)**(#%)**4

%+)%+"(&"***()$**(#%)**-$*
**(/%$))&"/%$*4$/%+,*!$*
**()%+*%**(#%)**1$)+(/%+(&"***()
-*$?#$+*$%((*%(*$*+(($*"%!)**$4


A

4
Pages 17-24 explain the different features available on this
thermostat.
Pairing with the RC1-W Receiver
If using with the UH1-W wiring centre, turn to page 6.
With the thermostat turned off:
numbers appear.
•The small number 01 in the top right corner of the LCD is the
feature number.
01 = RC1-W receiver.
•Use the Up/Down keys to set feature 06 to 01 (RC1-W).
You can now select a Receiver Address from 01-32.
•Use the Up/Down keys to set feature 07 to 01. (You should set
a unique receiver address for each receiver installed).

5
•Press A to accept, the display will now go blank.
Pairing the thermostat
Comms LED comes on.
5 seconds. The thermostat will send a signal for 1 minute, and
will flash the RF signal icon.
If successful, the Comms LED on the receiver will flash.
pairing.
•If the pairing is unsuccessful, check features 06 and 07 have
been configured correctly, to eliminate a possible signal issue
repeat the pairing process again.
Feature 08 does not need altering as the heang
output will always be assigned to zone 1 on the
receiver & the hot water output will be on zone 2.

6
Pairing with the UH1-W Wiring Centre
On the UH1-W wiring centre, take note of the
number set on the rotary switch (Board ID number
1-9). Each UH1-W on the system will need a different ID number.
With the thermostat turned off:
numbers appear.
•The small number 01 in the top right corner of the LCD is the
feature number.
RC1-W receiver.
•Use the Up/Down keys to set feature 06 to 00 (UH1-W).
Address).

7
• Use the Up/Down keys & set the large digits to the board
address of the UH1-W, this is the number set on the UH1-W
rotary switch. (You should set a unique board address on each
UH1-W installed).
• Press Clock again unl you see feature 08 (Zone Number,
01-08). The UH1-W is an 8 zone receiver. Use the up/down
buons to select the zone this thermostat should be linked to.
• Press Clock again unl you see feature 09.
00 = Under-floor heang, 01 = Radiators. Use the up/down
buons to select if the thermostat is controlling Under-Floor
heang or radiators.
• Press A to accept, the display will now go blank.
• Press the power buon once to turn the thermostat back on,
press the up buon & set the target temperature above the
room temperature, the flame symbol should then appear and
the assigned zone on the UH1-W should now be acvated.
This indicates pairing between the thermostat & the UH1-W is
successful.

8
He ng On
He ng Off – Frost Mode
Key Lock
RF Signal Ac ve
Ba ery
Holiday Ac ve
Timer On/Off Hot water on/off

9
#&')*'(&".
%%##&K))*+(($*(%%#*#&(*+(4
)K))**#&(*+(/%+(*(/$*%,$/%+(
%#4

))$)"%!
%)**"%!1%""%-*)*&)"%-4
•***(#%)***+($%$1&())*"%!+**%$
*(*#)
•%+($%-"*%)**%+()+)$*&5%-$
!/)
•())*%&*
•%+($%-"*%)**#$+*)+)$*
&5%-$!/)
•())*%&*


G


10
•%+($%-"*%)**/%*-!+)$*
&5%-$!/)
•())*%)*%($.*


%!$)'#%())
*(#%)**)!/6"%!"*/4%$"1%""%-*)
)*&)2

•())$%"*$%-$!/%(?>)%$)
•%+-"")*"%!)/#%"&&(
•%+$"%!1(&**)*&)%,4






?>

11
Comfort Levels Explained
The Heatmiser PRTHW-W provides Weekday/Weekend or 7 Day
The thermostat is supplied with comfort levels already
pro
are:
08:00 – 21C (Wake)
09:30 – 16C (Leave)
16:30 – 22C (Return)
23:00 – 17C (Sleep)
If you only want to use 2 levels, you should program the unused
levels to --.––

12
• To begin programming the comfort levels, press Clock
Once
• If your thermostat is setup for Weekday/Weekend
programming, you will see Mon-Fri shown. For 7 day
programming you will see Monday, you need to use
Up/Down arrow keys to select which day you would
like to program and then press H key to confirm.
• Using the Up/Down arrow keys, enter the required
Wake me
• Press H
• Using the Up/Down arrow keys, enter the required
Wake temperature
• Press H
• You will see Leave
• You should repeat the programming for each period,
entering --.– for unused periods.
• Press A to accept to confirm any changes made.

13
•
•
•
•
•
•
•

14
•
•
•
•
•

15

16
•
•
•
The Heatmiser PRTHW-W has a holiday funcon. This allows you to
enter a holiday seng. During a holiday, the thermostat will
maintain the frost set temperature. At the end of your holiday,
the thermostat will revert back to the programmed seng
ensuring that your home is warm on your arrival.

17
•
•

18