hebvest BW01HD User manual
hebvest.com t 800.469.8908 | f 407.264.6309 | mike@hebvest.com
operator’s manual
Belgian Waffle Baker - 7”
performance • reliability • simplicity
Model No. Description Watts.
BW01HD Belgian Waffle Baker 7” 1000
hebvest.com t 800.469.8908 | f 407.264.6309 | mike@hebvest.com
Belgian Waffle Baker - 7”
general installation:
operating instructions:
programming of baking temperature:
programming of baking time:
1. Install the Waffle Baker in the most convenient location for ease of
cleaning, maintenance and general operation. If the appiance is to
be positioned in close proximity to a wall, partitions, kitchen furniture,
decorative finishes, etc. it is recommended that they be made of a
non-combustible material. If not, they shall be clad with a suitable
non-combustible heat insulating material, and the closest attention
be paid to fire pre-vention regulations.
2. Switch power on via “Mains” rocker switch (A). The buzzer will sound
three times The LED display will appear with the set baking time.
1. Allow the unit to preheat to the set temperature. An amber light on the front panel will be illuminated
while the unit is still preheating.
2. Once the green light illuminates on the front panel, the unit has reached the set temperature, and is
ready for baking.
3. Generously apply “SPRAY AND COOK” or similar product onto the plates.
4. Place the desired amount of batter on the bottom plate, close the top lid using the handle provided,
and turn the handle clockwise by 180 degrees.
5. To activate the rundown timer, press the “Stop / Start” key (F) once.
6. The rundown timer will now proceed to count down.
7. Once the baking cycle is complete, the buzzer will sound, alerting the user that the product is baked.
8. To reset, press the “Stop / Start” key (F) once.
9. To remove the product, using the handle provided, turn the handle “counter clockwise” by 180
degrees, open the unit and remove the product.
10. Before continuing with the next bake, ensure that the green light is illuminated, indicating that the
preheat temperature has been attained.
1. Press and hold down the “Set” key (B) and then press the “start /stop” key (F). The LED display will
show the set baking temperature.
2. To change the temperature, scroll “Up” or “Down” using the keys (D) and (E) on the keypad until
the required temperature is reached.
3. Once the desired temperature has been reached, press the “Set” key(B) to store the setting.
4. To check the set temperature repeat step 1
1. The timer can be set in minutes and seconds, as indicated on the LED display.
2. To increase the baking time, press and hold down the “Up” key, then press the “Start / Stop” key (F)
repeatedly to set the required time.
3. To decrease the baking time, press the “Down” key, then press the “Start/ Stop” key (F) repeatedly
to set the required time.
4. Press the “Set” key (B) to store the preset time.
hebvest.com t 800.469.8908 | f 407.264.6309 | mike@hebvest.com
Belgian Waffle Baker - 7”
exploded view:
Part No. Description
1 LID/BASE PRESSING
2 LID CLAMPING PLATE
3 SMALL LID SPACER
4 LARGE LID SPACER
5 ELEMENT CLAMPING PLATE
6 115V 500W ELEMENT
7 TOP WAFFLE BAKER CASTING
8 TEMPERATURE PROBE
9 HANDLE EXTENSION
10 WAFFLE BAKER HANDLE
11 BOTTOM WAFFLE BAKER CASTING
12 NON-ILLUMINATED ROCKER SWITCH
13 CONTROL PC BOARD
14 CONTROL FACIA
15 PIVOT REST
16 RUBBER FOOT
17 BOTTOM PIVOT CASTING
18 TOP PIVOT CASTING
19 PIVOT AXLE
20 OUTER ENCLOSURE
21 BOTTOM COVER PLATE
22 COMPONENT MOUNTING PLATE
23 CONTACTOR
24 CERAMIC CONNECTOR BLOCK
25 TRANSFORMER
26 BACK POST
27 BRASS PIVOT BUSH
28 SMALL PIVOT BRACKET
29 LARGE PIVOT BRACKET
30 PIVOT LOCKING BUSH
31 BACK PLATE
32 CABLE GLAND
33 POWER CORD
hebvest.com t 800.469.8908 | f 407.264.6309 | mike@hebvest.com
Belgian Waffle Baker - 7”
wiring diagram:
cleaning guide:
LEGEND DESCRIPTION PART NUMBER
MSI Main Switch RS-WBA-1001
RI 12V Relay 1-RELAY-WBA1001
E1/E2 Element 500W 115V 5-500W-WBA1001
P1 Temperature Probe 1-TC-WBA1001
EC1 Electric Control 1-PCB-WBA1001
T1 Transformer 1-TRA-WBA-1001
1. Always ensure that the appliance is disconnected from the main power supply before
cleaning.
2. This appliance should not be cleaned with a water jet or immersed in water. use only
a damp cloth or sponge dipped in soapy water. Failure to observe this instruction will
invalidate the warranty
3. Wipe off the appliance with a dry cloth and wait at least half an hour before re –
connecting to the main power outlet.
4. The plates are Teflon coated and should only be cleaned with a damp cloth. Under no
circumstances should the plates be cleaned with abrasive wool as this will invalidate
the warranty
