Heiko YR-HRC01 User manual

CONTENTS
1. Products Lineup ......................................................................................................................1
2. Remote controller....................................................................................................................2
2.1 YR-HRC01............................................................................................................................2
3. Wired controller .......................................................................................................................6
3.1 YR-C01.......................................................................................... .......................................6

1
1. Products Lineup
No. Control system Model Photo
1Individual control Remote Controller
2
YR-HRC01
YR-C01
Individual control Wired Controller

2
2.Remote controller
MRV
LCAC
Smart Power Super Match R410A ON/OFF R22 ON/OFF
√ √
•On/Off, Mode, Fan speed, Temperature setting, Swing
•°C/ °F selection
•Individual control
•Three grades of fan speed
•Individual blade control for Smart Power Cassette
•Clock & Timer
•Moving eye control (Follow/Evade function)
2.1YR-HRC01

3
External View of Remote Controller Loading of the battery
1. Remove the battery cover;
2. Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder); Be sure that the loading is
in line with the “+”/ “-”;
3. Load the battery, then put on the
cover again.
<1> <2> <3>
Functional description
1. Power-up and Show All: the LCD display shows all
symbols in this function. 3s later, it just shows time and
the initial time is AM 12:00. The initial time is adjustable
and will be conrmed automatically 10s later.
2. ON/OFF Button: press the button for power on. The
initial default mode is SMART, otherwise it will be the
mode before power OFF. Press OFF button after power
on.
3. SMART Button:
(1) SMART button is always valid during power ON/
OFF;
(2) Press SMART button to execute power OFF in
SMART mode;
(3) In OFF and other modes, press SMART button to
enter initial default setting of SMART mode. LCD setting
temperature is not showed;
(4) In SMART mode, press TEMP. +/- button to show
the setting temperature.
4. COOL Button, HEAT Button and DRY Button
(1) When the remote controller in ON, press COOL
button, HEAT button and DRY button to execute COOL
mode, HEAT mode and DRY mode.
(2) For initial power-up, temperature and fan speed
will be showed as follows when entering each mode,
otherwise parameters set last time will be showed;
Mode SMART HEAT COOL DRY FAN
Initial
TEMP. 24°C 24°C 24°C 24°C
Setting
temperature
is not
showed.
Mode SMART HEAT COOL DRY FAN
Initial
Fan
Speed
AUTO LOW HI AUTO LOW
5. FAN Mode
(1) During power OFF, press “HEALTH” button or
“FRESH” button to enter FAN mode with low fan speed.
Meanwhile, the HEALTH or FRESH icon will be showed
on the screen.
(2) Temperature is not showed in FAN mode.
(3) Auto fan speed is not available when switching fan
speed in FAN mode.

4
6. FAN SPEED Button:
(1) In other modes except for Fan mode, LOW, MED, HI
and AUTO fan speed is adjustable, switching sequence
is as LOW-MED-HI-AUTO-LOW.
LOW, MED and HI fan speed
circulate automatically
LOW MED HI AUTO FAN SPEED
(2) After TURBO or QUIET is set. Press TURBO
button to show on the screen with fan speed as
, then press “FAN SPEED” button to exit;
press QUIET button to show on the screen with
fan speed as , then press “FAN SPEED” button to
exit. To cancel TURBO and QUIET, press TURBO and
QUIET buttons respectively, and icons
will disappear and the fan speed will return to the last
one.
(3) This button is invalid during power OFF.
7. TEMP. +/- Button:
(1) This button is invalid in FAN mode;
(2) Temperature adjustment range in SMART, HEAT,
COOL and DRY mode: 16 ~30°C.
(3) Press and hold “TEMP. +/- “ button, the temperature
changes once; long press the button, the temperature
changes rapidly.
8. Four-side Embedment
(Available for some models):
(1) Initial position of all modes for rst power on:
SMART HEAT COOL DRY FAN
Four-side
Embedment
Show
all
Show
all
Show
all
Show
all
Show
all
SWING
Angle
Position
3
Position
5
Position
3
Position
3
Position
3
(2) After power on, press “Four-side Embedment” button
for the rst time and the recycle approach is as follows:
four-side simultaneous control of Four-side Embedment
→ Four-side Embedment 1 → Four-side Embedment
2 → Four-side Embedment 3 → Four-side Embedment
4 → Four-side simultaneous control of Four-side
Embedment.
(3) When pressing “Four-side
Embedment” button to select air deector, the selected
air deector ashes. Press “Up-and-down Angle” button
to adjust angle of air deector at the moment.
10. Right-and-left SWING Angle (Available for some
models):
Recycle approach: 34 showed (Position 1)→25 showed
(Position 2)→16 showed (Position 3)→1 showed
(Position 4)→2 showed (Position 5)→5 showed (Position
6)
→6 showed (Position 7)→Auto swing
Auto swing approach:
1→2→3→4→5→6→5→4→3→2→1 are
showed circularly.
9. Up-and-down SWING Angle:
1: Position 1; 2: Position 2; 3: Position 3; 4:
Position 4;
5: Position 5; 6: Position 6 (reserved)
Recycle approach: Position 1→Position
2→Position 3 →Position 4→Position
5→AUTO→Position 1
Auto swing: 1→2→3→4→5→4→3→2→1 is
showed circularly.
1
2
3
654
1
2
3
654
1236
5
4
11. HEALTH AIRFLOW (Available for some models):
Press "HEALTH AIRFLOW" button to show icon on
LCD display. Each air deector of swings on four sides
alternates circularly to indicate that the swing rotates
to exhaust air. Meanwhile, up-and-down SWING angle
shows AUTO SWING. Press it again to cancel HEALTH
AIRFLOW.
12. SLEEP:
(1) Valid during power on.
(2) The SLEEP time is fixed to 8 hours and is not
adjustable.
(3) It is invalid in FAN mode. When setting TIMER ON or
TIMER ON to TIMER OFF after setting SLEEP function,
once the timer setting is successful, the SLEEP function
will be cancelled; after setting TIMER ON or TIMER
ON to TIMER OFF, the SLEEP function cannot be set.
SLEEP function can be set from TIMER OFF to TIMER
ON, TIMER OFF and SLEEP function have priority in
canceling the opposite side.
13. HEALTH:
(1) During power-on or power-OFF, press “HEALTH”
button to display icon on LCD display, and press
“HEALTH” button again to cancel.
(2) During power-OFF, press “HEALTH” button to enter
Fan mode, start low wind and HEALTH function, display
icon .
(3) Switch among modes, and keep HEALTH function.
(4) If HEALTH function is set, power OFF and then on to
stay in HEALTH mode.
14. ECO:
(1) Press ECO button and the display will show .
(2) ECO is valid under all modes, it is memorized
among switch of all modes.
(3) ECO function power-on or power-OFF is memorized.
15. Turbo/Quiet:
(1) Press button “Turbo”, display icon on remote
LCD display, display icon of fan speed;
Press button “Quiet”, display icon on remote
LCD display, display icon of fan speed.
(2) Turbo and QUIET functions can not exist at the
same time, the latter will replace the former.
Show 1s Show 1s Show 1s Show 1s Show 1s

5
(3) If Turbo function is set, press “SLEEP” button to
exit turbo, which means that setting SLEEP function
while canceling turbo function. At the same time, the
icon disappears and icon is shown; if QUIET
function is set at present, press button “SLEEP” while
QUIET function is still kept.
(4) This function is valid under the mode of COOL or
HEAT.
(5) Turbo/QUIET functions are not memorized among
switch of all modes/the state of on or OFF.
16. IFP:
(1) Press “IFP” button, display , IFP function is
set, and press “IFP” button again to cancel.
(2) Press “Follow/Evade” button, display that
expresses following; press it again, display that
expresses evading. Press it the third time to cancel.
(3) If follow/evade functions are set, air-out angle will
change with position of people, so after setting these
functions, Four-side Embedment icons in all sides, up-
and-down SWING and left-and-right SWING icons will
disappear.
(4) If air conditioner is in the state of HEALTH airow,
follow/evade functions is set, HEALTH airow function is
cancelled, Four-side Embedment, up-and-down SWING
and left-and-right SWING icons will disappear.
17. FRESH:
(1) FRESH function is valid under the state of ON or
OFF. When air conditioner is OFF, press “FRESH”
button, display icon on LCD display to enter Fan
mode and low speed. Press “FRESH” button again, this
function is cancelled.
(2) After FRESH function is set, ON or OFF functions
are kept.
(3) After FRESH function is set, mode switch function is
kept.
18. 10°C Heating Function and °C/°F function
Press “MENU/°F” button to set 10°C Heating function
and °C/°F function. 10°C Heating Function is valid only
under the mode of HEAT, and it is not memorized under
the state of ON or OFF.
19. HEATER:
(1) When HEAT mode is chosen and is displayed on
LCD display, pressing “HEATER” button can cancel and
set HEATER function.
(2) Auto mode will not start HEATER function
automatically, but can set or cancel HEATER function.
20. Timer:
(1) TIMER ON
• Press “TIMER ON” button, character “ON” is ashing,
press “+/-“ button to adjust, then press “CONFIRM”
button to conrm, if “CONFIRM” button is not pressed
within 10 s, TIMER ON function is cancelled.
•If time of TIMER ON is the same as that of clock at
present, character “ON” is always ashing and can
not be veried, it is necessary to readjust time.
•When the time of TIMER ON is end, the setting time
and character “ON” disappear.
(2) TIMER OFF
•Press “TIMER OFF” button, character “OFF” is
ashing, press “+/-“ button to adjust, then press
“CONFIRM” to conrm, if “CONFIRM” is not pressed
within 10 s, TIMER OFF function is cancelled.
•If time of TIMER OFF is the same as that of clock at
present, character “OFF” is always ashing and can
not veried, it is necessary to readjust time.
•When the time of TIMER OFF is end, the setting time
and character “OFF” disappear.
(3) TIMER ON/OFF
•After TIMER ON/OFF is set, remote will automatically
judge sequential order of ON/OFF, arrow indicates
that the one performed rst points to the one performed
second.
• After the time of clock performed rst is end,
corresponding characters of timer “ON/OFF”
disappear.
•If time of TIMER ON is the same as that of TIMER
OFF, and can not be veried, corresponding character
of the latter of setting time is always ashing, it is
necessary to readjust time and conrm again.
•If time of TIMER ON/OFF is the same as that of clock
at present, and can not be veried, it is necessary to
readjust time and conrm again.
(4) After setting timer, display the setting of timer rst
and then display time all the time, when timer is active,
character “ON/OFF” is always displayed.
21. Button +/-:
Press button “+/-“, time will change in terms of 1 min as
unit, pressing and holding the button will change quickly.
22. Clock:
Press “Clock” button, “AM” or “PM” displayed at present
are ashing to enter the state of clock adjustment,
adjust clock and then press “CONFIRM” to conrm.
It is valid under the state of ON/OFF.
23. LIGHT:
No display on remote controller LCD, which is
processed by indoor unit.
24. RESET:
Perform one power on reset operation when RESET
button is pressed.
25. LOCK:
Press button Lock, display Lock symbol on LCD display,
buttons on remote controller can not be used, press
button Lock again to unlock.
26. CODE: Function reserved.
27. INQUIRE Function reserved.
NO. 0150519129

6
3. Wired controller
3.1 YR-C01
MRV
LCAC
Smart Power Super Match R410A ON/OFF R22 ON/OFF
√√√√
•On/Off, Mode, Fan speed, Temperature setting, Swing.
•Individual & Group control (Max.16 indoor units)
•Simple and Smart design, 86*86*13.05mm
•Touch button with back light
•Timer/ Clock
•Easy installation

7
B0TT0M CASE
>ABS<
Dimension

8
Parts and Functions
Interface Display
24-hour, press once to minus one minute. Keep pressing, minus 2 minutes in 1 second’s pressing, then 10
minutes in 5 seconds. The time will keep decreasing at the pace of 10 minutes a time in 10 seconds. Vice-versa.
Press to conrm or it will turn back to the previous state automatically in 10s.
Press this key to execute mode switch. For detailed information, please refer to mode setting.
Note: If using Fresh Air unit, default 3 modes will circulate from cooling→heating→fan→cooling.
Key
ON/OFF
Adjusting key for temperature, clock, timer, sleeping adjustment, temp. compensation and energy saving;
Inquiring key for detail parameter and malfunction inquiry;
Switching key for function switch.
The adjusting accuracy of temperature is 0.5°C. If energy saving mode is not set, the adjusting range is from 16°C
to 30°C. If energy saving mode is set, the lowest temperature limit of cooling/dry and the highest temperature
limit of heating are decided by the setting of the chip, the default cooling/dry temperature is 23°C, and the default
heating temperature is 26°C.
Note:
•If the dip switch Sw2 is “on”, it displays the ambient temp., as well as when powered off. From power off to power
on, mode switching and set temp. adjustment, it ashes to display SET icon and statically displays the set temp..
And then statically displays the ambient temp. and ROOM icon after 3 seconds. In energy saving mode and
temp. compensation mode, the adjusting step is 1°C a time.
• If using Fresh Air unit, set temp. cannot be adjusted. If there is no Central/Lock set, the temp. will be xed at 18°C
in cooling and 22°C in heating. The Up/Down key will not display in normal state, but will display and valid in timer
setting, function selection, unit shift in malfunction inquiry, parameter shift in parameter check, unit No. setting,
sleeping time adjustment, etc.