heimgard 16A User manual

Quick start guide version 1.0
Requires a heimgard hub
In-wall Switch
16A

Device
overview
NC
S
Zigbee In-Wall Switch
FRONT VIEW
Load output
Switch input
AC 100-240V
power input
Reset button LED Indicator

Device
Specications
Input voltage Output
voltage
Output
current
Size
(LxWxH)
100-240VAC 100-240VAC 16A max 45.5x45x20.3 mm

Product
Specications
Compatible Load Types
Load Symbol Load Type Maximum Load Remarks
LED lamps with
transformers
1220W @ 230V
580W @ 110V
Due to variety of LED lamp designs,
maximum number of LED lamps is
further dependent on power factor
result when connected to switch
LED drivers 1220W @ 230V
580W @ 110V
Maximum permitted number of
drivers is 1220W divided by driver
nameplate power rating
Incadescent lighting,
HV Halogen lamps
3680W @ 230V
1760W @ 110V
Low voltage halogen
lighting with electronic
transformers
1220W @ 230V
580W @ 110V
Electrical appliances
such as television,
refrigerator, water
heating etc.
3680W @ 230V
1760W @ 110V

Wiring
Notes for the diagrams:
L - terminal for live lead
N - terminal for neutral lead
L1 - output terminals of the device
(controlling connected light source)
S - terminal for external switch
NC - No Connection
L
N
NC
S
Zigbee In-Wall Switch
GND

Connecting to
the Hub
These steps are to be followed after the switch
has been properly installed and wired by a
certied electrician.
1. At the circuit breaker, turn o the power to the
switch.
Open the Heimgard app and follow the steps
listed here to connect to your device
2.
Manage
Devices

3. Turn the circuit breaker power on to your switch.
It will automatically enter pairing mode.
The LED indicator light on the switch will ash 2
times slowly to indicate pairing.
4. When the LED indicator ashes 5 times and then
remains on the device has been found in your
app.
5. You will now see the In-wall switch in your new
devices list. Congure the switch by giving it a
name and adding it to a room.
Your device is able to be controlled by your app,
remote control or with on-wall switch.

Factory Reset
If your switch has previously been connected to a dierent Hub, you
may need to perform a factory reset.
Quickly press the reset button 5 times continuously.
If you do not have access to the device, turn on and
o the power supply 5 times from the either the
curcuit breaker or light switch.
NC
S
Zigbee In-Wall S wit ch
Press 5
times
1.

2. The device that is connected to this switch will
ash or turn on/o 3 times to indicate success-
ful reset.
You will have to recongure your device.
Note: make sure your light bulb is functioning
properly

Website: heimgard.com/support
Email: [email protected]
Facebook: facebook.com/heimgardnorge/
Telephone: [phone]
Need help?
Visit heimgard.com for
more information and tips
on how to use.

Important safety
information
1. Read through these instructions and follow accordingly.
2. Clean only with dry soft cloth. Household cleaners and solvents
can damage the nish on your device.
3. Do not install near any heat sources such as radiators, heat
registers, stoves or other device that produce heat.
4. Do not use this device near water.
5. Warning: To reduce the risk of re or electric shock, do not
expose this device to rain or moisture.
6. Do not expose device to dripping or splashing.
7. Protect the attached cables from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point the
exit the apparatus.
8. Only use attachments/accessories specied by the manufacturer.
9. Unplug this device during lightning storms or when unused for
long periods of time.
10. All servicing should be performed by qualied service personnel.
Servicing is required when the device has been damaged in any
way.
11. Operating temperature: -10°C to +50°C
12. Operating relative humidity: < 95% RH (no condensation)
Dispose the product properly at the end of life. This is electronic
waste which should be recycled accordingly.

heimgard.com