HF Protoss-PG46 User manual

Protoss-PG46 User Manual
http://www.iotworkshop.com - 1 -
Protoss-PG46
RS485/Ethernet to 4G Router
User Manual
V 1.0
Overview of Characteristic
Use MIPS MCU (32MB SRAM) and 16MB Flash, based on Linux OS
Support LTE-TDD, LTE-FDD, WCDMA, TD-SCDMA, cellular network, sub-type to support specific
cellular network
Support RS485 to 2G/3G/4G Data Transmission, UART baud rate Up to 460800bps
Support 10/100M Ethernet to 2G/3G/4G Data Transmission
Supports Max 5 Channel TCP/UDP connections, Each Connection Supports 1400 Bytes of Data
Cache
Support Multiple Working Modes: Network Transparent Transmission Mode, HTTP Mode, MQTT,
WebSocket

Protoss-PG46 User Manual
http://www.iotworkshop.com - 2 -
Support Modbus Master Function
Support IOTService Tool, Remotely and Dynamically Modify Module Parameters
Support APN
Support VPN(PPTP, L2TP, L2TP+IPSEC)
Supports Registration Packet, Heartbeat Packet Function, and Packet Supports Combination of
ICCID, IMEI, IMSI, Software Version, cellular network Connection Status.
Support NTP
Support Modbus TCP to Modbus RTU
Support IOTBridge for Remote Control and Config.
Support IOTBridge working time, for example only works from 10:00 to 10:30 to save the data flow
charge.
Support Network OTA Upgrade Firmware.
Multiple Type of Different Power Input：
◼Protoss-PG46-H：100～240VAC@50～60Hz
◼Protoss-PG46-M：9～48VDC@1A
Size: 102.03 x 64.95 x 27.50 mm (L x W x H) ，C45 rail installation

Protoss-PG46 User Manual
http://www.iotworkshop.com - 3 -
TABLE OF CONTENTS
TABLE OF CONTENTS....................................................................................................................3
LIST OF FIGURES............................................................................................................................4
LIST OF TABLES .............................................................................................................................4
1. PRODUCT OVERVIER ........................................................................................................5
1.1. General Description.........................................................................................................5
1.2. Device Parameters...........................................................................................................5
1.3. Key Applications..............................................................................................................7
2. HARDWARE INTRODUCTION ...........................................................................................8
2.1. APPEARANCE..................................................................................................................8
2.2. Interface Definition ..........................................................................................................9
2.3. RS485 Interface..............................................................................................................10
2.4. Mechanical Size .............................................................................................................10
2.5. Product Installation .......................................................................................................12
2.6. Product Order Information............................................................................................13
3. FUNCTION DESCRIPTION ...............................................................................................14
APPENDIX A: CONTACT INFORMATION....................................................................................15

Protoss-PG46 User Manual
http://www.iotworkshop.com - 4 -
LIST OF FIGURES
Figure 1. Protoss-PG46 Appearance..............................................................................................................8
Figure 2. Protoss-PG46 Interface ...................................................................................................................9
Figure 3. Protoss-PG46-H Interface Definition................................................................................................9
Figure 4. Protoss-PG46-H Interface Definition..............................................................................................10
Figure 5. Protoss-PG46 Mechanical Size.....................................................................................................12
Figure 6. C45 Rail Installation.......................................................................................................................12
Figure 7. Protoss-PG46 Product Order Information......................................................................................13
LIST OF TABLES
Protoss-PG46 Series Defination.............................................................................................................5
Protoss-PG46 Technical Specifications..................................................................................................5
HISTORY
V 1.0 05-29-2020. First Version

Protoss-PG46 User Manual
http://www.iotworkshop.com - 5 -
1.PRODUCT OVERVIER
1.1. General Description
The Protoss-PG46 support LTE-TDD, LTE-FDD, WCDMA, TD-SCDMA, cellular network full network.
4G network support maximum download data rate 150Mbps, upload data rate 50Mbps.
The Protoss-PG46 supports TCPIP protocol, with its RS485 interface, it makes traditional UART
device easy connecting to IOT.
Protoss-PG46 include different sub-type, as following table.
Protoss-PG46 Series Defination
1.2. Device Parameters
Protoss-PG46 Technical Specifications
Item
Parameters
System Information
Processor/Frequency
320MHz
Flash/SDRAM
16MB/32MB
Operating System
OpenWRT Linux
2G/3G/4G Interface
Transmit Power
LTE-TDD: Class 3(23dBm+1/-3dB)
LTE-FDD: Class 3(23dBm±2dB)
WCDMA: Class 3(24dBm+1/-3dB)
TD-SCDMA: Class 3(24dBm+1/-3dB)
GSM900: Class 4(33dBm±3dB)
DCS1800: Class 1(30dBm±3dB)
GSM900 8-PSK: Class E2(27dBm±3dB)
DCS1800 8-PSK: Class E2(26dBm±3dB)

Protoss-PG46 User Manual
http://www.iotworkshop.com - 6 -
Receive Sensivity
FDD B1: -96dBm(10M)
FDD B3: -96dBm(10M)
FDD B5: -96dBm(10M)
FDD B8: -96.5dBm(10M)
TDD B38: -96dBm(10M)
TDD B39: -97dBm(10M)
TDD B40: -96.5dBm(10M)
TDD B41: -96dBm(10M)
WCDMA B1: -110dBm
WCDMA B8: -111dBm
TDSCDMA B34: -109dBm
TDSCDMA B39: -109dBm
GSM 900M: -109dBm
GSM 1800M: -109dBm
LTE
Maximum Support non-CA CAT4
Support 1.4~20MHz RF Bandwidth
Downstream Support Multiple Users MIMO
FDD: Maximum Upstream Rate 50Mbpsm Maximum
Downstream Rate 150Mbps
TDD: Maximum Upstream Rate 35Mbpsm Maximum
Downstream Rate 130Mbps
WCDMA
3GPP R8 DC-HSPA+
16-QAM,64-QAM and QPSK Modulation
Maximum Upstream 5.76Mbps
Maximum Downstream 42Mbps
TD-SCDMA
CCSA Relese 3
Maximum Upstream 2.2Mbps
Maximum Downstream 4.2Mbps
GSM/cellular network
R99：
CSD Transmission Rate：9.6Kbps/14.4Kbps
cellular network：
Support cellular network multi-slot class 12
Code Method：CS-1/CS-2/CS-3/CS-4
Ethernet
Port Number
1
WAN/LAN switchable
Interface
10/100M Base-T
Transformer
Integrated
Serial Port
Port Number
1
Interface Standard
RS485
Data Bits
7,8
Stop Bit
1,2
Check Bit
None,Even,Odd
Baud Rate
TTL：1200 bps~460800 bps
Flow Control
No Flow Control
Half-Duplex(RS485)
Software Flow Contorl
Software
Configuration
Serial AT Command
IOTService Serial Port Configuration Software
IOTService Network Configuration Software
Firmware Upgrade
UART or OTA Upgrade
Network Protocol
IP，TCP，UDP，DHCP，DNS，HTTP Server/Client，ARP，

Protoss-PG46 User Manual
http://www.iotworkshop.com - 7 -
AutoIP，ICMP，Telnet，NTP，Modbus TCP
Encryption
TLS v1.2
AES 128Bit
DES3
Basic Parameter
SIM Card
Nano SIM card(1.8V/3V)
Size
102.03 x 64.95 x 27.50 mm
Operating Temp.
-25 ~ 70°C
Storage Temp.
-45 ~ 105°C, 5 ~ 95% RH（no condensation）
Input Voltage
Protoss-PG46-H：100～240VAC@50～60Hz
Protoss-PG46-M：9～48VDC@1A
Average Working
Current
~300mA@9V
Peak Current
2A
1.3. Key Applications
The Protoss-PG46 module connects the serial device to the Internet and conforms to the TCP/IP
protocol for transmitting serial data.
⚫Remote device monitoring
⚫Production asset tracking and monitoring
⚫Security field
⚫Industrial sensors and controllers
⚫Health medical equipment
⚫ATM equipment
⚫Data acquisition equipment
⚫UPS power management equipment
⚫Telecommunication equipment
⚫Data display device
⚫Hand-held device
⚫Attendance system and terminal equipment

Protoss-PG46 User Manual
http://www.iotworkshop.com - 8 -
2.HARDWARE INTRODUCTION
Protoss-PG46 is a cellular network solution for serial device networking. Data transmission via cellular
network makes product integration very easy. This product meets EMC Class B security level and can
pass relevant certification tests in various countries.
2.1. APPEARANCE
Figure 1. Protoss-PG46 Appearance

Protoss-PG46 User Manual
http://www.iotworkshop.com - 9 -
2.2. Interface Definition
Figure 2. Protoss-PG46 Interface
Figure 3. Protoss-PG46-H Interface Definition
Pin
Description
Net Name
Signal
Type
Comment
1
AC Power Input
L
Power
100～240VAC Input
2
AC Power Input
N
Power
5
RS485_B-
IO
RS485 B-
6
Signal GND
GND
Power
Used for RS485 GND, usually leave it
unconnected
7
RS485_A+
IO
RS485 A+
ANT
Antenna
ANT
2G/3G/4G SMA Antenna
RJ45
Ethernet
RJ45
I/O
10/100M Ethernet
Default is LAN function, can be configured to
WAN Function, connect to router LAN port for
network access.
SIM
SIM Slot
Nano SIM
Reload
Restore to factory
setting button
Reload
I
Detailed functions see <Notes>
Reset
Reset button
Reset
I
Hardware reset button
Net
Network status LED
Net
O
Boot On: Bootup is OK.
2s Off -> 2s On: Cellular network Register is
OK.
0.1s Off -> 0.1s On: Cellular network data is
transferring.

Protoss-PG46 User Manual
http://www.iotworkshop.com - 10 -
Pin
Description
Net Name
Signal
Type
Comment
Active
UART/Ethernet
Data Transfer
Active
O
On: Ethernet connection OK
Off: No Ethernet connection
0.1s Off -> 0.1s On: UART data transfer
Power
Power LED
Power
O
On: Power input OK
Off: Power input NG.
Link
Server connection
LED
Link
O
On: SOCK A connection OK.
Off: no Socket A connection.
Figure 4. Protoss-PG46-H Interface Definition
Pin
Description
Net Name
Signal
Type
Comment
1
DC Power Input
VCC+
Power
9～48VDC@1A Input
2
DC Power Input
GND-
Power
Other Pin definition is the same as above
<Notes>:
I —Input; O —Output; Power—Power Supply
nReload Pin (Button) function:
1.After module is powered up, long press this button (“Low” > 3s) and loose to make the
module recover to factory setting.
2.3. RS485 Interface
RS485 use two wire links, A(DATA+), B(DATA-). Connect A(+) to A(+), B(-) to B(-) for communication.
Suggest to connect GND together when interference is very severe.
The RS485 interface support maximum 32 485 device, device. The cable maximum length is 1200
meters. Need to add 120Ohm terminal resistor for over 300 meters.
2.4. Mechanical Size
The dimensions of Protoss-PG46 are defined as following pictures(mm):

Protoss-PG46 User Manual
http://www.iotworkshop.com - 11 -

Protoss-PG46 User Manual
http://www.iotworkshop.com - 12 -
Figure 5. Protoss-PG46 Mechanical Size
2.5. Product Installation
Figure 6. C45 Rail Installation

Protoss-PG46 User Manual
http://www.iotworkshop.com - 13 -
2.6. Product Order Information
Based on customers detailed requirements, we provide different configuration Protoss-PG11, details
as below:
Figure 7. Protoss-PG46 Product Order Information

Protoss-PG46 User Manual
http://www.iotworkshop.com - 14 -
3.FUNCTION DESCRIPTION
Refer to “IOT_Device_Series_Software_Funtion” document for more detailed function.

Protoss-PG46 User Manual
http://www.iotworkshop.com - 15 -
APPENDIX A: CONTACT INFORMATION
------------------------------------------------------------------------------------------------------------
Address: Room1002 , #1Building, No.3000 Longdong Avenue, Pudong District, Shanghai,
China 201202
Website: www.iotworkshop.com or www.hi-flying.com
Contact:
Sales：[e-mail]
Support：[e-mail]
Service：[e-mail]
Business：[e-mail]
---------------------------------------------------------------------------- -------------------------------
For more information about us, please visit our website: www.iotworkshop.com
< END OF DOCUMENT >