Juniper J2300 Operator's manual

J-series™Services Router Quick Start
12 October 2007
Part Number: 530-021980-01
Revision 1
J-series Services Routers provide IP routing, WAN and LAN connectivity, and
management services. Available in several models, Services Routers typically connect
small, branch, or regional offices to a central site, and link Internet service provider
(ISP) networks.
The J-series Services Router Quick Start provides instructions to initially set up J2300,
J2320, J2350, J4350, and J6350 Services Routers. You need no previous JUNOS
software experience, but must have managed a network and configured other routers.
For more information, see the J-series documentation at http://www.juniper.net/techpubs.
Contents What You Need To Know ................................................................................3
Management IP Address ...........................................................................3
J-Web Access ............................................................................................3
CLI Console Access ...................................................................................3
Required Licenses .....................................................................................3
Slot Numbers ............................................................................................4
Interfaces and Ports ..................................................................................4
Remote Access .........................................................................................4
Before You Begin .............................................................................................4
Installing a Services Router .............................................................................6
Installing J2300 Services Routers ..............................................................6
Installing J2320 and J2350 Services Routers .............................................6
Installing J4350 or J6350 Services Routers ................................................8
Connecting Power to a Services Router ...........................................................8
Basic Connection and Configuration with the J-Web Interface .........................9
Step 1. Connecting, Logging In, and Starting the J-Web Interface .............9
Step 2. Updating the Software with the J-Web Interface ..........................10
■1

Step 3. Adding Licenses with the J-Web Interface ...................................11
Step 4. Configuring Basic Settings with J-Web Quick Configuration .........11
Basic Connection and Configuration with the CLI ..........................................13
Step 1. Connecting, Logging In, and Starting the CLI ..............................13
Step 2. Updating the JUNOS Software with the CLI .................................14
Step 3. Adding Licenses with the CLI ......................................................14
Step 4. Configuring Basic Settings with the CLI .......................................14
J-Web Basics ..................................................................................................15
JUNOS CLI Basics ..........................................................................................16
Safety Warnings Summary ............................................................................18
Compliance Statements .................................................................................21
Related Juniper Networks Documentation .....................................................23
Requesting Support .......................................................................................26
Revision History ............................................................................................26
2■
J-series™Services Router Quick Start

What You Need To Know
Management IP Address
When you first connect a management PC or laptop to a built-in Ethernet port on a
Services Router, the router acts as a DHCP client and attempts to perform an
autoinstallation. If it does not find a DHCP server, the router assigns 192.168.1.1/24
as the IP address for port 0. (If you are connected to port 1, 192.168.2.1/24 is
assigned as the IP address. On the J2320, J2350, J4350 and J6350 routers, port 2
and port 3 are assigned 192.168.3.1/24 and 192.168.4.1/24, respectively.)
Because this address is not part of any explicit configuration, it is removed when
you change the configuration in any way. You must configure an IP address for this
LAN port when you commit your initial configuration. (See “Step 4. Configuring Basic
Settings with J-Web Quick Configuration”on page 11 or “Step 4. Configuring Basic
Settings with the CLI”on page 14.)
J-Web Access
The Web interface to the router—called the J-Web interface—is enabled by default.
To configure the router with the Web interface, you attach a PC or laptop to a built-in
Ethernet port. The examples in this document use the first built-in Ethernet port:
■On J2300 routers, the first built-in Ethernet port is Fast Ethernet PORT 0 (internally
named fe-0/0/0).
■On J2320, J2350, J4350 and J6350 routers, the first built-in Ethernet port is
Gigabit Ethernet port 0/0 (internally named ge-0/0/0).
See “Step 1. Connecting, Logging In, and Starting the J-Web Interface”on page 9.
CLI Console Access
Services Routers are shipped with a console cable and adapter. To configure a Services
Router through the console port with the JUNOS command-line interface (CLI), you
use a terminal emulation program such as Microsoft Windows HyperTermimal. (See
“Step 1. Connecting, Logging In, and Starting the CLI”on page 13.)
Required Licenses
To use the following features on a Services Router, you must purchase a license. (See
“Step 3. Adding Licenses with the CLI”on page 14 or “Step 4. Configuring Basic
Settings with J-Web Quick Configuration”on page 11.)
■Advanced Border Gateway Protocol (BGP) support for route reflectors
■Data link switching (DLSw)
■J-Flow traffic analysis
What You Need To Know ■3
What You Need To Know

Slot Numbers
J2300 routers have built-in WAN ports. Other models have slots for replaceable
Physical Interface Modules (PIMs):
■J2320 Services Routers—Slots 1 through 3 are numbered from top to bottom
and left to right.
■J2350 Services Routers—Slots 1 through 5 are numbered from top to bottom
and left to right.
■J4350 and J6350 Services Routers—Slots 1 through 6 are numbered from top to
bottom and left to right.
Interfaces and Ports
Interfaces are named by type, slot number, module number (always 0), and port
number. Port numbering starts with 0. For example:
■On J2300 routers, built-in Fast Ethernet LAN PORT 0 and PORT 1, which are in
slot 0, are named fe-0/0/0 and fe-0/0/1.
■On J2320, J2350, J4350, and J6350 routers, the built-in Gigabit Ethernet LAN
ports 0/0 through 0/3, which are in slot 0, are named ge-0/0/0, ge-0/0/1,
ge-0/0/2, and ge-0/0/3.
■On models with replaceable PIMs, the first port on a T1 PIM in slot 1 is named
t1-1/0/0.
Remote Access
Although Telnet and SSH are both supported, they are disabled by default.
Before You Begin
Before installing and connecting a Services Router, read “Safety Warnings
Summary”on page 18.
Then make sure you have the equipment listed in Table 1 on page 5.
4■Before You Begin
J-series™Services Router Quick Start

Table 1: Equipment Required for Services Router Installation
Management AccessAll Other ModelsJ2300 Model OnlyAll Models
For CLI access:
■Management device,
such as a PC or laptop,
with a serial port (not
provided)
■RJ-45 console (Ethernet
“rollover”) cable, with
an RJ-45-to-DB-9
adapter (both provided)
For J-Web access:
■Management device,
such as a PC or laptop,
with an Ethernet port
(not provided)
■Ethernet cable (not
provided)
■For rack installation,
mounting screws
appropriate for your rack
(not provided).
■Routers with redundant
power supplies require
an AC power cord
(provided) or DC power
cables (not provided) for
each power supply.
■Mounting brackets are
preinstalled on J2320
and J2350 models, and
must be installed on
J4350 and J6350 models.
■For desk installation,
four rubber feet
(provided)
■For rack installation,
four mounting
screws appropriate
for your rack (not
provided)
■For wall installation,
four wall screws or
anchors capable of
supporting the full
weight of the chassis,
up to 12 lb (5.4 kg)
■Electrostatic discharge (ESD)
grounding strap (not
provided)
■For rack or wall installation,
a screwdriver appropriate
for the screws or anchors
(not provided)
■For AC power, an AC power
cord with a plug appropriate
for your geographical
location (provided)
■For DC power, 14 AWG DC
power cables with
appropriate lugs (not
provided)
■For grounding, 14 AWG
grounding cable and lug for
the router (not provided)
CAUTION: A licensed electrician must attach a cable lug to the grounding and power
cables that you supply. A cable with an incorrectly attached lug can damage the
router.
If you are installing a J4350 or J6350 Services Router, take the following steps:
1. Attach the air filter and filter cover, as shown in Figure 1 on page 5.
Figure 1: Attaching Air Filter and Filter Cover
2. Attach the mounting brackets to either the center or front of the chassis, as
shown in Figure 2 on page 6.
Before You Begin ■5
Before You Begin

Figure 2: Attaching Mounting Brackets
Installing a Services Router
WARNING: A DC-powered J2300 Services Router is intended for installation in a
dedicated equipment room where it is accessible by trained personnel only. Other
DC-powered Services Routers are intended for installation in a restricted access
location.
Installing J2300 Services Routers
To install a J2300 Services Router on a desk, attach the rubber feet to the underside
of the chassis.
To install a J2300 Services Router on a wall, attach the rubber feet to the chassis
underside, attach a mounting bracket to each side of the chassis, and attach the
brackets to the wall. (For instructions, see the J2300, J4300, and J6300 Services Router
Getting Started Guide.)
To install a J2300 router in a rack:
1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and
connect the strap to an outside ESD point.
2. Make sure the rack is properly secured to the building in its permanent location.
3. Attach a mounting bracket to each side of the router chassis.
4. Have one person grasp each side of the router, lift the router, and position it in
the rack.
5. Have a second person install a mounting screw into each of the bracket holes
that are aligned with the threaded holes in the rack.
Installing J2320 and J2350 Services Routers
To install the J2320 and J2350 router into a rack:
6■Installing a Services Router
J-series™Services Router Quick Start

1. Have one person grasp the sides of the router, lift the router, and position it in
the rack.
2. Align the top hole in each mounting bracket with a hole in each rack rail as shown
in Figure 3 on page 7 and Figure 4 on page 7, making sure the chassis is level.
Figure 3: Hanging a J2320 Router in a Rack
Figure 4: Hanging a J2350 Router in a Rack
3. Have a second person install a mounting screw into each of the two aligned
holes. With a number 2 Phillips screwdriver, tighten the screws.
4. Verify that the mounting screw on one side of the rack is aligned with the
mounting screw on the opposite side and that the router is level.
5. Install the second screw in each mounting bracket.
Installing a Services Router ■7
Installing a Services Router

Installing J4350 or J6350 Services Routers
To install a J4350 or J6350 Services Router in a rack:
1. Make sure the rack is properly secured to the building in its permanent location.
2. Attach a screw to each rack rail in the third hole down from where you want the
top of the router to be positioned, as shown in Figure 5 on page 8. Screw only
part way in, leaving about 1/4 in. (6 mm) distance between the screw head and
the rail.
3. Lift the router and insert the elliptical openings in the mounting brackets onto
the partially inserted screws so that the router is hanging from the two screws.
Figure 5: Hanging the Router in the Rack
4. Install at least two mounting screws into each mounting bracket, in addition to
the center screws from which the router hangs.
Connecting Power to a Services Router
J2300, J2320, J2350, and J4350 Services Routers have a fixed power supply. J6350
Services Routers have field-replaceable AC or DC power supplies.
To connect AC or DC power:
1. Connect the router to earth ground with a 14 AWG grounding cable:
a. Connect one end to a proper earth ground point (the rack, for example).
b. Remove the screw and washer from the PEM nut on the protective earthing
terminal at the rear of the router chassis. (The J4350 and J6350 chassis have
two PEM nuts.)
8■Connecting Power to a Services Router
J-series™Services Router Quick Start

c. Secure the other end of the cable to this grounding point with the washer
and then with the screw.
2. For an AC power supply only:
a. Insert the appliance coupler end of the power cord into the appliance inlet
on the router's power supply faceplate.
b. Insert the plug into an AC power source receptacle.
c. If the power supply includes a on/off switch, turn the switch to on.
3. For a DC power supply only:
a. Ensure that the voltage across the DC power source cable leads is 0 volts
and that the cable leads cannot become active during installation.
b. Remove the clear plastic cover protecting the terminal block.
c. Remove the two center screws next to the labels –48 VDC and RTN.
d. Secure the positive (+) DC source power cable lug to the RTN terminal,
tightening the screw only until snug. Do not overtighten.
e. Secure the negative (–) DC source power cable lug to the –48 VDC terminal,
tightening the screw only until snug. Do not overtighten.
f. Replace the plastic cover.
4. Repeat Step 2 or Step 3 for the second power supply, if one is installed.
For complete instructions, see the Getting Started Guide for your router.
Basic Connection and Configuration with the J-Web Interface
For J-Web access, you connect from your management PC or laptop to the Services
Router through one of the built-in Ethernet interfaces. The examples in this document
use port 0. (For information about the J-Web interface, see “J-Web Basics”on page 15.)
Step 1. Connecting, Logging In, and Starting the J-Web Interface
When the Services Router is powered on for the first time, it searches for a DHCP
server, and if it does not find one, it assigns an IP address within the 192.168.1.0/24
subnetwork to any devices connected to it.
To connect to the J-Web interface through port 0/0 on the router:
Basic Connection and Configuration with the J-Web Interface ■9
Basic Connection and Configuration with the J-Web Interface

1. On the management device, such as a PC or laptop, you use to access the J-Web
interface, verify that the address of the port that you connect to the router is set
to one of the following:
■An Ethernet address on the 192.168.1/24 subnetwork other than
192.168.1.1
■An Ethernet address from a DHCP server
2. Turn off the power to the management device.
3. Plug one end of the Ethernet cable into the Ethernet port on the management
device.
4. Connect the other end of the Ethernet cable to the built-in Ethernet port on the
router.
5. Power on the router by pressing the power button on the front panel.
6. Wait until the STATUS LED on the front panel turns solid green.
7. Turn on the power to the management device. The router assigns an IP address
to the management device within the 192.168.1/24 subnetwork if the device
is configured to use DHCP.
8. From the management device, open a Web browser and enter the IP address
192.168.1.1 in the address field. The Set Up Quick Configuration page appears.
9. Configure basic settings for your router as described in “Step 4. Configuring Basic
Settings with J-Web Quick Configuration”on page 11.
NOTE: You must manually configure the IP address for the management port you
are using before you save your initial configuration. When you save the configuration
for the first time, the DHCP lease is lost and you will lose the connection to the router
if you have not manually configured the IP address. If you lose connection through
the management interface, you must connect through the console port.
Step 2. Updating the Software with the J-Web Interface
After starting up the Services Router, you might want to download the latest version
of the JUNOS software from the Juniper Networks Web site and load it onto the
router. To update the JUNOS software:
1. Go to http://www.juniper.net/support, and follow the links to download the JUNOS
software for J-series routers to your PC or laptop.
2. Log in to the J-Web interface.
3. Click Manage>Software>Upload software package.
4. Click Browse, locate the JUNOS software package file on your PC or laptop hard
drive, and open the file.
5. Select the check box next to Reboot If Required, and click Upload Package.
For complete instructions, see the J-series Services Router Administration Guide.
10 ■Basic Connection and Configuration with the J-Web Interface
J-series™Services Router Quick Start