Perle IDS-105G User manual

Perle IDS-105G (XT)
Unmanaged 10/100/1000
Ethernet Switches
P/N 5500340-10 (Rev D)
Installation Guide

- 2 - IDS-105G Installation Guide
Overview
This document contains instructions necessary for the installation
and operation of the Perle IDS-105G Ethernet switch. This
Ethernet switch can be ordered as a 5-port RJ-45 switch or as a
5- port RJ-45 switch with either one fiber port (SC or ST) or up to
two SFP transceiver ports. The fiber port can be either single
mode (SM) or multimode (MM) depending on the model selected
and they can operate over different wavelengths and distances.
The SFP transceiver ports support SFP’s supplied by Perle, Cisco
or other manufacturers of MSA complaint SFP modules.
Visit the Perle website for the most up to date installation guides,
models and specifications. http://www.perle.com/
Note: xxxxxxxx indicates models numbers for this product line.
TP = twisted pair
* fiber characteristics are determined by the SFP inserted
XT – Industrial Temperature Models
Models Port 1-5 Port 6 Port 7
IDS-105G TP (RJ-45) None None
IDS-105G-xxxxxxxx TP (RJ-45) Fiber port Not applicable
IDS-105G-SFP TP (RJ-45) SFP transceiver
port * Not applicable
IDS-105G-DSFP TP (RJ-45) SFP
transceiver
port *
SFP transceiver
port*
IDS-105G-XT TP (RJ-45) None None
IDS-105G-SFP-XT TP (RJ-45) SFP transceiver
port* Not applicable
IDS-105G-DSFP-XT TP (RJ-45) SFP
transceiver
port*
SFP transceiver
port*
IDS-105G-xxxxxxxx-XT
TP (RJ-45) Fiber port Not applicable

IDS-105G Installation Guide - 3 -
Features
•10/100/1000Base-T, 1000Base-X, SC/ST/SFP fiber ports,
multi/single mode
•Pluggable SFP transceiver ports
•IEEE 802.3/802.3u/802.3x
•1000Base-SX /LX/LH /BX-U/BX-D /EX /ZX
•10/100/1000Base-T, Full/Half duplex, auto-negotiation on
copper ports
•Redundant DC power inputs
•Rugged high-strength case
•Industrial temperature models
•DIN-rail or wall/panel mounting
Note – In this guide the various models will be referred to as
the IDS-105G
Getting to know your IDS-105G Switch
Package Contents:
•IDS-105G
•DIN-rail mounting clip (pre-installed on the unit)
•This guide
Note – optional panel/wall mounting kits may be ordered

- 4 - IDS-105G Installation Guide
Front View of IDS-105G (5 port RJ-45)

IDS-105G Installation Guide - 5 -
Front View of IDS-105G (with two SFP transceiver
ports)

- 6 - IDS-105G Installation Guide
Front View of IDS-105G (with one fiber port)

IDS-105G Installation Guide - 7 -
Bottom view of the IDS-105G (with fiber
port)
Top view of the IDS-105G
Power
The IDS-105G switch has two power inputs that can be connected
simultaneously to DC or AC power sources. If one power source
fails, the other acts as a backup, and automatically powers the
switch.
Reset Button
To reset the IDS-105G insert a paper clip into the air hole vent
and gently press the reset button. The LEDs on the IDS-105G will
go On and then momentarily Off when released to show that the
unit has been reset. All links will be dropped and the MAC tables
will be cleared.

- 8 - IDS-105G Installation Guide
LED Status
P1 / P2– Power (Green LED)
On: Power present
Off: No Power Present
6 (Port 6 – Fiber or SFP) (Green LED)
On: Link up
Flashing: Link up and Ethernet activity detected
Off: Link down
7 (Port 7 – SFP) (Green LED)
On: Link up
Flashing: Link up and Ethernet activity detected
Off: Link down
Ethernet Port Status
Port Link / Speed (Green and Yellow LEDs)
On: Link up
o1000 Mbps:Green On; Yellow Off
o100 Mbps: Green On; Yellow On
o10 Mbps: Green Off; Yellow On
Flashing: Link up and Ethernet activity detected
Off: Link Down

IDS-105G Installation Guide - 9 -
Views for the IDS-105G
Note: all dimensions are in mm

- 10 - IDS-105G Installation Guide

IDS-105G Installation Guide - 11 -
Mounting the IDS-105G on a DIN-rail
1. The DIN-rail clip will be fixed to the back panel of the IDS-
105G switch when you receive the product.
2. Position the IDS-105G switch such that the top of the DIN-rail
fits into the slot on the top of the DIN-rail clip, just below the
hook and behind the spring.
3. While pushing down on the unit to compress the spring rotate
the bottom of the IDS-105G toward the rail. This will snap the
bottom of the rail into the bottom of the clip. See diagram
below.
Note: To remove the IDS-105G switch from the DIN-rail, push
down slightly on the IDS-105G while pulling the bottom out.

- 12 - IDS-105G Installation Guide
Mounting the IDS-105G to the Wall
1. Remove the DIN-rail clip from the rear panel on the IDS-105G.
2. Attach the wall mount plates to the IDS-105G switch as shown
below using the screws provided in the kit.
3. Use the wall mount plates as a guide to mark the spots where
the screws will be.
4. Drive the screws into the wall leaving about 2 mm of the screw
protruding from the wall to allow room for sliding the wall
mount panel between the wall and the screws.
5. Once the screws are fixed to the wall, insert the four screw
heads through the large parts of the keyhole shaped screw
openings.
6. Pull the IDS down to lock the IDS-105G to the wall mount.
7. Tighten the four screws securely to the wall.
Note: For the best results use screws that have the following attributes:
Head diameter .5 - .6 mm
Shaft diameter 3 - 3.5 mm
Note: the dimensions are in mm

IDS-105G Installation Guide - 13 -
Wiring up the IDS-105G
Power sources must be off prior to beginning the power connection
steps.
Ensure that the voltage and current ratings of the intended power
source are appropriate for the IDS-105G as indicated on the product
label.
Ensure that the installation and electrical wiring of the equipment is
performed by trained and qualified personnel and that the installation
complies with all local and national electrical codes
If this unit is to be installed in a location where the ambient
temperature exceeds 50C, the case temperature may exceed safe
levels. For this reason, this unit should be installed in a restricted
access location where access can only be gained by service
personnel or users who have been instructed about the reasons for
the restrictions applied to the location and about any precautions that
shall be taken; and access is through the use of a tool or lock and
key, or other means of security, and is controlled by the authority
responsible for the location.
Hazardous Location Warnings
(safe conditions for use:)
Subject devices are to be installed in an ATEX Certified IP54 (as
defined in IEC 60529) enclosure and accessible only by the use of a
tool.
Subject devices are for use in an area of not more than pollution
degree 2 in accordance with IEC 60664-1.
These devices are open-type devices that are to be installed in an
enclosure with tool removable cover or door, suitable for the
environment.
This equipment is suitable for use in Class I, Division 2, Groups
A,B,C,D or only non hazardous locations only.
WARNING –EXPLOSION HAZARD – Do not disconnect equipment
unless power has been removed or the area is known to be non-
hazardous
WARNING EXPLOSION HAZARD – Substitution of any components
on this switch may impair suitability for Class I, Division 2.
Provision shall be made to prevent the rated voltage being exceeded
by the transient disturbances of more than 140% of the peak rated
voltage.

- 14 - IDS-105G Installation Guide
Connecting the IDS-105G to ground
If your installation requires additional grounding follow this
procedure.
1. Follow the manufacturer’s instructions for attaching the ground
wire to grounding lug.
2. Attach the grounding lug to the chassis and secure with the
grounding screw provided.
Grounding the chassis requires the following items:
•One grounding lug (not provided)
•One 12 AWG wire (not provided)
Connecting Power to the IDS-105G
1. Ensure the power source is off prior to connection.
2. Strip both wires (12-20 AWG) 5 mm (3/16
th
inch).
3. Loosen the terminal block screws and connect positive (+) /
negative (-) wires into the -/+ terminals.
4. Tighten terminals screws 0.51Nm torque.
5. Ensure the wires are securely fastened.
6. Re-insert the Terminal block connector if removed.
7. Turn on power source.
8. Check that the P1 LED is On.
9. If desired connect P2 (power source 2, beginning at Step 1).
10. One individual conductor for each clamping point.

IDS-105G Installation Guide - 15 -
Ethernet Copper Cabling Requirements
•Category 5 UTP or STP
•24-22 AWG
•Straight through or Ethernet crossover cable
Connect the copper cables from each TP port (RJ-45) on the IDS-
105G switch to Ethernet-enabled devices. See below for pinouts.
8-pin RJ-45
Remaining pins not used.
Fiber Port Cabling Requirements
MM: 50/125 microns or 62.5/125 microns
SM: 9/125 microns
Connect the fiber cables to Port 6/7 on the IDS-105G and the
other end to a compliant fiber devices. If you are making your own
fiber cables, remember that the RX on one side needs to go to TX
on the other side and vice versa. See diagram below.
RX
X
RX
X

- 16 - IDS-105G Installation Guide
Technical Specifications
Connection
Dual input terminal block power
Power Input/Consumption
9.6 to 60 VDC, 1.25A max
18 to 30 VAC, 0.67A max 50/60 Hz
Reverse Polarity Protection Yes
Interface
RJ-45 10/100/1000Base-T, auto negotiation speed, F/H duplex
mode and auto MDI/MDI-X connection
Fiber Ports 1000Base-X (SC or ST connectors)
SFP transceiver ports One or two transceiver ports (depending on model) for
1000Base-X SFP’s
LED indicators P1 – power 1
P2 – power 2
Ports 1 – 8 G/Y –Link/Activity/Speed
Port 6 – port status (Fiber or SFP models)
Port 7 – port status (SFP models)
Environmental
Operating Temperature
Commercial Models
IDS-105G-(D)SFP and IDS-105G-xxxxxxxx
Industrial Models
IDS-105G-(D)SFP-XT and IDS-105G-xxxxxxxx-XT
0°C to 60°C (32°F to 140°F)
-40°C to 75°C (-40°F to 167°F)
Storage Temperature
Commercial Models
IDS-105G-(D)SFP and IDS-105G-xxxxxxxx
Industrial Models
IDS-105G-(D)SFP-XT and IDS-105G-xxxxxxxx-XT
-25°C to 70°C (-13°F to 158°F)
-40°C to 85°C (-40°F to 185°F)
Operating Humidity 5% to 90% non-condensing
Storage Humidity 5% to 95% non-condensing
Operating Altitude Up to 3,048 m (10,000 ft)
Regulatory Approvals
Safety cUL 60950-1, EN 60950-1
Industrial UL 508
Hazardous Locations ANSI/ISA 12.12.01-2013 Class I Division 2
Groups A-D
ATEX Class I Zone 2
CENELEC EN 60079-0:2012+A11:2013
CENELEC EN 60079-15:2010
IEC 60079-0 Edition 6 – Revision Date
2012-11-01
IEC 60079-15 – Edition 4 – Issue Date
2010-01-01
Laser Safety Transmitters: EN60825-1:2007
FDA/CDRH 21
CFR1040.11/CFR1040.11
EMI/EMC FCC Part 15 – Class B
CISPR22 / EN55022 Class B
EN55024 Class B

IDS-105G Installation Guide - 17 -
Fiber Specifications
IDS-105G models
Fiber Connector
SFP transceiver ports
Mode
Distance
Wavelength (nm)
TX Power (dB)
RX Power (dB)
Budget
IDS-105G(-XT) None n/a n/a n/a n/a n/a n/a
IDS-105G-SFP*( -XT) None one - - - - - -
IDS-105G-DSFP* (-XT)
None two - - - - - -
IDS-105G-M2SC05-(XT)
SC None
MM
duplex 550 m 1804 ft TX: 850 RX:850 Min:-9.5
Max:-4 Min:-17
Max:-3 7.5
IDS-105G-M2ST05-(XT)
ST None
MM
duplex 550 m 1804 ft TX: 850 RX:850 Min:-9.5
Max:-4 Min:-17
Max:-3 7.5
IDS-105G-M2SC2 SC None
MM
duplex 2 km 1.2 miles TX: 1310 RX:1310 Min:-6 Max:0 Min:-17
Max:-3 11
IDS-105G-M2ST2 ST None
MM
duplex 2 km 1.2 miles TX: 1310 RX:1310 Min:-6 Max:0 Min:-17
Max:-3 11
IDS-105G-S2SC10(-XT)
SC None
SM
duplex 10 km 6.2 miles TX: 1310 RX:1310 Min:-9.5
Max:-3 Min:-20
Max:-3 10.5
IDS-105G-S2ST10(-XT)
ST None
SM
duplex 10 km 6.2 miles TX: 1310 RX:1310 Min:-9.5
Max:-3 Min:-20
Max:-3 10.5
IDS-105G-S1SC10U(-XT
)
SC None
SM
duplex 10 km 6.2 miles TX: 1310 RX:1490 Min:-9 Max:-3 Min:-20
Max:-3 11
IDS-105G-S1SC10D(-XT
)
SC None
SM
duplex 10 km 6.2 miles TX: 1490 RX:1310 Min:-9 Max:-3 Min:-20
Max:-3 11
IDS-105G-S1SC20U SC None
SM
duplex
20 km
12.4 miles
TX: 1310
RX1490 Min:-8 Max:-3 Min:-22
Max:-3 14
IDS-105G-S1SC20D SC None
SM
duplex
20 km
12.4 miles
TX: 1490
RX:1310 Min:-8 Max:-3 Min:-22
Max:-3 14

- 18 - IDS-105G Installation Guide
IDS-105G-S2SC40 SC None
SM
duplex 40 km 24.9 miles
TX: 1310
RX:1310 Min:-3 Max:-5 Min:-23
Max:-3 20
IDS-105G-S2ST40 ST None
SM
duplex 40 km 24.9 miles
TX: 1310
RX:1310 Min:-3 Max:-5 Min:-23
Max:-3 20
IDS-105G-S1SC40U SC None
SM
duplex 40 km 24.9 miles
TX: 1310
RX:1490 Min:-3 Max:-2 Min:-23
Max:-3 20
IDS-105G-S1SC40D SC None
SM
duplex 40 km 24.9 miles
TX: 1490
RX:1310 Min:-3 Max:-2 Min:-23
Max:-3 20
IDS-105G-S2SC70 SC None
SM
duplex 70 km 43.5 miles
TX: 1550
RX:1550 Min:-2 Max:5 Min:-23
Max:-3 21
IDS-105G-S2ST70 ST None
SM
duplex 70 km 43.5 miles
TX: 1550
RX:1550 Min:-2 Max:5 Min:-23
Max:-3 21
IDS-105G-S1SC80U ST None
SM
simplex
80 km
49.7 miles
TX: 1510
RX:1590 Min:-2 Max:3 Min:-26
Max:-3 24
IDS-105G-S1ST80D ST None
SM
simplex
80 km
49.7 miles
TX: 1590
RX:1510 Min:-2 Max:3 Min:-26
Max:-3 24
IDS-105G-S2SC120 SC None
SM
duplex 120 km 74.6 miles
TX: 1550
RX:1550 Min:0 Max:5 Min:-32
Max:-9 32
IDS-105G-S1SC120U SC None
SM
simplex
120 km
74.6 miles
TX: 1510
RX:1590 Min:-2 Max:3 Min:-26
Max:-3 24
IDS-105G-S1SC120D ST None
SM
simplex
120 km
74.6 miles
TX: 1590
RX:1510 Min:-2 Max:3 Min:-26
Max:-3 24
IDS-105G-S2SC160 SC None
SM
duplex 160 km 100 miles TX: 1550 RX:1550 Min:0 Max:5 Min:-32
Max:-9 32
IDS-105G-S2ST160 ST None
SM
duplex 160 km 100 miles TX: 1550 RX:1550 Min:0 Max:5 Min:-32
Max:-9 32
* fiber characteristics are determined by the SFP inserted

IDS-105G Installation Guide - 19 -
Product Label (samples)
For models IDS-105G-(D)SFP and IDS-105G-xxxxxxxx For models IDS-105G-(D)SFP-XT and IDS-105G-xxxxxxxx-XT
Contacting Technical Support
Contact information for the Perle Technical Assistance Center (PTAC)
can be found at the link below. A Technical Support Query may be made
via this web page.
www.perle.com/support_services/support_request.shtml
Warranty / Registration
This product is covered by the Perle Ethernet Switches Warranty.
Details can be found at:
http://www.perle.com/support_services/warranty.shtml
Copyright © 2014 Perle Systems Limited all rights reserved. No part of
this document may be reproduced or used in any form without written
permission from Perle Systems Limited.